ORiNG TGPS-1080-M12-BP2-24V Quick Installation Manual

EN50155
Switch
Q I
I N D U S T R I A L
uick nstallation
Introduction
With 24VDC power supply, the TGPS-1080-M12-24V
BP2-24V unmanaged Gigabit PoE Ethernet switches are designed for
industrial applications, such as rolling stock, vehicle, and railway
applications. The switches boast EN50155 compliance and M12 connectors
to ensure tight and robust connections, and guarantee reliable operation
against environmental disturbances, such as vibration and shock. Both
models feature eight 10/100/1000Base-T(X) P.S.E. ports which are able to
provide sufficient power for those power-hungry devices with up to 30Watts
per port. Therefore, you can attach an IEEE 802.3af-compliant device to the
switch without requiring additional power. The
model also provides two sets of bypass ports that ensure constant network
connectivity during power failure. Even if the switch loses power, traffic
will continue to flow unimpeded through the link.
Package Contents
The TGPS-1080-M12-24V/ TGPS-1080-M12-BP2-24V
following items. If any of these items is missing or damaged, please contact
your customer service representative for assistance.
Contents Pictures
TGPS-1080-M12-24V or
TGPS-1080-M12-BP2-24V
QIG
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Q I G
TGPS-1080-M12 Series
TGPS-1080-M12 Series
G
uide
Dimension
and TGPS-1080-M12-
15.0
TGPS-1080-M12-BP2-24V
65.0 21.3
TGPS-1080-M12-24V
are shipped with the
Panel Layouts
Front View
Number
1
TGPS-1080-M12
PWR PWR1 PWR2
1
2
3
4
1
V1+
V1-
5
Power
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1: Hold the
Step 2: Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Step 3: Slide the
1907-2-29-TGPS1080M12-1.0
125.0
86.0
56.5
R2.5
15.0
R4.00
Relay N.C. Relay Output
3A@24VDC
TGPS-1080-M12 TGPS-1080-M12-BP2
PWR PWR1 PWR2 Fault PWR PWR1 PWR2
LNK/ACT
DPX/COL
PoE
G4 G8
LNK/ACT
DPX/COL
PoE
G3 G7
V1+ V2+ LNK/ACT V1+
DPX/COL
V1- V2- V1-
PoE
G2 G6
LNK/ACT
DPX/COL
PoE
G1 G5
Power Power
65.0 21.3
TGPS-1080-M12-BP2-24V
1. Power status LED
Relay
N.C. Relay Output
3A@24VDC 2. Power1 status LED
6
3. Power2 status LED
Fault
4. Fault LED
LNK/ACT
DPX/COL
5. Power port
PoE
G4 G8
6. Relay output port
LNK/ACT
7. LAN port LNK/ACT LED
DPX/COL
PoE 8. LAN port Duplex/Collision LED
G3 G7
7
9. Gigabit Ethernet ports
V2+
LNK/ACT
(G5-G8 of TGPS-1080-M12-BP2-24V are bypass ports)
V2- DPX/COL
PoE
G2 G6
10. PoE status LED
LNK/ACT
8
DPX/COL
PoE
G1 G5
9 10 9
d evice upright against the wall
d evice downwards and tighten the four screws for added stability.
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the switch
between the wall and the screws.
PRINTED ON RECYCLED PAPER
EN50155 8-port unmanaged
PoE Ethernet switch
Wiring
For pin assignments of power, console and relay output ports, please refer to the following tables.
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
125.0
86.0
56.5
R2.5
Power port pinouts
R4.00
The device supports two sets of power supplies and uses the M23 5-pin
Relay N.C. Relay Output
3A@24VDC
female connector on the front panel for the dual power inputs.
Fault
LNK/ACT
Step 1: Insert a power cable to the power connector on the device.
DPX/COL
PoE
G4 G8
Step 2: Rotate the outer ring of the cable connector until a snug fit is
LNK/ACT
DPX/COL
PoE Power
G3 G7 Failure achieved. Make sure the connection is tight.
Bypass
V2+ LNK/ACT
DPX/COL
V2-
PoE
G2 G6
LNK/ACT
DPX/COL
PoE Relay output port pinouts
G1 G5
The switch uses the M12 A-coded 5-pin male connector on
the front panel for relay output. Use a power cord with an
M12 A-coded 5-pin female connector to connect the relay.
The relay contacts will detect user-configured events and
form an open circuit when an event is triggered.
Bypass port pinouts
TGPS-1080-M12-BP2-24V includes 2 sets of bypass
ports that protect the network from failures by ensuring
network integrity during power loss.
Network Connection
The switch has eight 10/100/1000Base-T(X) Ethernet ports in the form of M12 connector. These
ports are PoE-enabled, and thus can deliver power over the same Ethernet cable. Depending on
the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect to network devices (Pcs,
servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
Cable Type Max. Length
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft)
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft)
Cat. 5/Cat. 5e 100-ohm
1000BASE-T UTP 100 m (328ft)
UTP
M12/8P Pin Definition
For pin assignments of the LAN ports, please refer to the following tables.
1 2
10/100Base-T(X) P.S.E. RJ-45 port
7 3
Pin No. Description
6 4
#1 TD+ with PoE Power input +
5
8
#2 TD- with PoE Power input +
#3 RD+ with PoE Power input -
#6 RD- with PoE Power input -
Version 1.0
V1+ V2+
V1- V2-
Relay
N.C.
1A@24VDC
1 2
7 3
6 4
5
8
Connector
8-pin female M12
A-coding connector
8-pin female M12
A-coding connector
8-pin female M12
A-coding connector
1000Base-T P.S.E. RJ-45 port
Pin No. Description
#1 BI_DA+ with PoE Power input +
#2 BI_DA- with PoE Power input +
#3 BI_DB+ with PoE Power input -
#4 BI_DC+
#5 BI_DC-
BI_DB- with PoE Power input -
#6
#7 BI_DD+
#8 BI_DD-
Quick Installation Guide