Cessna Hawk XP R172K Pilot Operating Handbook page 110

CESSNA 400 MARKER BEACON
(TYPE R-402A)
PILOT'S OPERATING RAN]) I
\I" II
SUPPLJo:MI'111
~. LOT'S OPERA TING HANDBOOK
'~PPLEMENT
.,[
TYPICAL INSTALLATION
ON ALL 150 MODEL SERIES
TYPICAL INSTALLATION
ON ALL 172, 177, 177RG,
180 & 185 MODEL SERIES
TYPICAL INSTALLATION
ON ALL 337 MODEL SERIES
TYPICAL INSTALLATION
ON ALL 182, 206, 207
& 210 MODEL SERIES
Figure 1. Cessna 400 Marker Beacon Operating Controls
and Indicator Lights (Sheet 1 of 2)
2
CESSNA ,1011
~LIIIII' II 1111;1\(
'ON
I I.
1'1 II ,III:!.")
1.
OFF/VOLUME CONTROL - The small, ""'"
,,,,,I.
the set on or off and adjusts the audio
li::k""'I' I, . I
wise rotation turns the set on and incn'a::":i
II,.
",.\1
, I, •• I
I, • I
,I I
II I l\iI
2. DIM/BRT CONTROL - The large, outer ,'",,1,
"I I"" ,.\,
light dimming for the marker lights. CI" •.•. ,
II' ,. ,,,I,
II .. "
increases light intensity.
3. TEST SWITCH - (150, 182, 206, 207, 21() s, :11; 1\1",
I , I
Series Only) When the press-to-test switch I
lid I '" ,
pressed, the marker beacon lights will i lluun
u.u-
,,,,I,
ting the lights are operational (the test pos ill
"II I
,I""
I
test function only).
NOTE
Turn the set on, and rotate the DIM coni 1'1,1 ,
I, •• I
wise (fully on) in order to view the mar-ke-r "'" ,,',
lights during test.
4. LO/HISENSSWITCH- (150,182,206,207,210,1 ',I,
Model Series Only) In the LO position (Up),
1'1 ••••
'1\.,,"
tivity is positioned for ILS approaches. In till'
III I'" ,II",
(Down), receiver sensitivity is positioned for
;111",,1';
II
'''I
5. SPEAKER/PHONE SWITCH - Selects speaker "I' 1'1,,,,,.
I,
aural reception.
6. MARKER BEACON INDICATOR lJGHTS - Indir.u.
I" '"
of outer middle and inner marker beacons. '1'1 ••.
I
I111
I II
light is blue, the MIDDLE light is amber and II
u:
111111
I '
11,101
is white.
7. HI/LO/TEST SWITCH - (172, 177, 177RG, 1B().' 11",1\1,1.
I
Series Only) In the HI position (Up), receiver
:;1'11"
II"
II
positioned for airway flying. In the LO posit.iou
{I', "I. ,I "
ceiver sensitivity is positioned for ILS approar I
u '
I
I" II••
TEST position (Down), the marker lights will illlllll'"
Ii,
dicating the lights are operational (the test pm:ill""
i· ,
I ""I'
test function only),
NOTE
Turn the set on, and rotate the BRIGHT ('0111,
" I
clockwise (fully on) in order to view the 11\:1 I I,. ,
beacon lights during test. The TEST posill"I' ""
the switch is spring loaded to return the
sw
II.
I,
I"
the LO SENS position when TEST posttiou I:: ,.
I. , , I
Figure 1. Cessna 400 Marker Beacon Opernt
"'1' ' ""I, I,
and Indicator Lights (Sheet 2 of 2)
;1
I