Tools And Supply Requirements; Quick Installation Setup And Operation Review - DIG LEIT-2 Operating Instructions Manual

3. 305DC-XXX complete in-line valve with solenoid or
S-305DC solenoid (one for each valve used)
4. 5-solenoid adapters are available to fit most valves:
a. Model 30-920 use with BERMAD 200 series HIT 500
series, Superior 950, Griswold 2000, DW and Hunter HBV
b. Model 30-921 use with RAIN BIRD DV, DVF, PGA, PEB, GB, EFB, BPE,
PESB and ASVF valves
c. Model 30-922 use with HUNTER ASV, HPV, ICV, PGV and AS VF series
valves
d. Model 30-923 use with WEATHERMATIC 12000, 21000 series valves
e. Model 30-924 use with IRRITROL 100, 200B, 205, 217B, 700 2400, 2500
and 2600 series valves and TORO P220, 252 and 220 valves series
f. Model 30-925 use with SUPERIOR 950, HUNTER HBV, TORO 252 (1.5"
and larger) and BUCKNER VB series.
A B C
A1 "O" ring B1 "O" ring C1 "O" ring
200-014 200-021 200-012
model #30-494
model #03-077 model #30-495
A2 Sleeve
C2 Long
model #30-424
sleeve
model #30-423
5. LEIT RC2 remote handset (version SW U:1.XX.XX EE 1.XX.XX)
to communicate with up to 99 LEIT-2 controllers.
D E F
D1 "O" ring E1 "O" ring F1 "O" ring
200-015 200-014 200-014
model #30-494 model #30-494 model #30-494
D2 Sleeve E2 Short
model #30-424 sleeve
model #30-422
8

1.3 Tools and Supply Requirements

1. Standard wire stripper
2. Philips screwdriver (#1) if using the valve clip attachment or the mounting
column plastic attachment or Philips screwdriver (#2) used with the valve
box mounting dome
3. Concrete: approximately 1, 90 lb (40 kg) bag (if using mounting column)
NOTE: Only needed with the mounting column
4. Waterproof wire connectors (not included)

1.4 Quick Installation Setup and Operation Review

In order to establish communication for the first time between a LEIT RC2
handset and LEIT-2 controller the following steps must be taken:
1. Charge the LEIT RC2 handset (see LEIT RC2 instruction)
2. Setup the LEIT RC2 handset (see LEIT RC2 instruction)
3. Install the LEIT-2 controller following the LEIT–2 installation instructions
and let it sit out in the light to harness light energy.
a. In bright light conditions (full sun) this will take under 30 min.
b. In shaded conditions this could take up to 2 hours
c. Communication will only initiate when the controller is fully charged
4. Follow the instructions steps of how to establish initial communication
between a LEIT-2 controller and LEIT RC2 handset.
STEP 1: Connect the two yellow sensor wires together (found on the
LEIT-2 controller) so that the LEIT RC2 remote handset can identify the
new controller (see LEIT RC2 handset operation instruction).
STEP 2: Using the LEIT RC2 Handset, select Default Setup and connect
to the LEIT-2 controller using Radio Uplink icon (see page 17).
STEP 3: After establishing communication between a LEIT RC2 handset
and a LEIT-2 controller, setup the controller selecting Setup icon found in
the Controller Menu. Then select Cont. Setup icon found in the Setup
Menu Screen (see RC2 handset operation instructions).
9