Typical Installation - Zip InLine ES4 Instruction Manual

®
Zip InLine ES
Electronic Instantaneous Water Heater for single outlet.
Model
Energy efficiency class
Pressure rating
Element type
Supply voltage
Nominal power rating @ 230V
Nominal current @ 230V
Temperature adjustment (installer)
Maximum inlet temperature
Factory set temperature
(1)
Factory set flow rate 38°C (l/min)
(2)
Switch on flow rate (l/min)
Switch off flow rate (l/min)
Required specific water resistance @ 15°C
Rated volume
Filled weight
Water connections
Dimensions W x D x H
Protection class (IEC529)
All data quoted at nominal supply voltage.
A minimum water pressure of 0.2 MPa (2 bar) is recommended for optimum performance.
The appliance must not be subject to more than 1 MPa (10 bar).
(1) Subject to incoming water temperature, flow rate and supply voltage.
(2) Based on 12°C supply temperature, 3 bar dynamic pressure and 230V supply voltage.
Description
• The ES is designed to provide
hot water for handwash in areas
where space is limited.
• Heating power controlled
electronically for temperature
stabilisation.
• Outlet temperature can be preset
inside the unit between 30°C and
43°C (factory set at 38°C).
• Flow adjustment control, preset
for a temperature increase of
25°C.
• Stainless steel bare-wire heating
system for very quick response.
• Double pole thermal cut-out
protection.
• Choice of special kits available
complete with heater, tap and
fittings.
• Supplied with 700mm of pre-
wired cable.
• Easy to install with wall bracket.
Approvals
WRAS approval and CE endorsed.
Warranty
One year, on-site parts and labour.
For full details of the Zip Warranty
Scheme visit
www.zipwater.com/uk/support/
warranty-policy.
Specification Sheet InLine ES range 2016
ES3 ES4
A A
1MPa
Bare wire
1/N/PE 230 V~
2.8kW 4.4kW
12A 19A
30°C - 43°C
70°C
38°C
1.5 2.4
1.2 1.5
1.0 1.3
>1100 ohm.cm >800 ohm.cm
0.2 litres
1.5 (kg)
1/2" BSP
186mm x 87mm x 135mm
IP25
Installation
Location
The appliance must be installed
in a frost free environment. Zip
ES products comply with IP25 and
may be installed in zone 1. The unit
should be installed as close as
possible to the outlet to avoid heat
loss.
Plumbing
The appliance is intended for
connection to the mains water
supply. It should be installed by a
suitably qualified person.
The appliance may be used as an
unvented installation (as shown in
the diagram opposite) or as a vented
installation.
Electrical
The appliance must be earthed and
connected to the mains supply by
means of permanent wiring through
suitable isolation having a contact
separation of 3mm in all poles and
may only be operated if measures
have been taken to protect against
shock-hazard voltages.
Installation must be installed in
accordance with current IEE
regulations.
Technical Support
Contact Zip on 0845 6 005 005 or
0345 6 005 005.
Optional Touch Free Taps
ES6
Long reach
A
basin/sink tap
TF001—Mains powered
TF002—Battery powered
Standard reach
basin/sink tap
5.5kW
TF003—Mains powered
24A
TF004—Battery powered
Tubular wall
mounted tap
TF005—Battery powered
TF006—Mains powered
3.0
Tubular deck
1.5
mounted tap
1.3 TF007
—Battery powered
TF008
—Mains powered
>800 ohm.cm
Pillar tap
TF009—Dual powered
Remote control
TF100
IMPORTANT For correct operation of the ES models it
is essential that the special tap nozzle supplied with the
heater is fitted to the tap spout.
Only taps, such as those indicated above, with removable
M22 / 24 nozzles should be used.

Typical Installation

N.B. Zip InLine instantaneous water heating is the most
efficient available, however, delivered water temperature is
dependent on local incoming water temperature and supply
voltage. Quoted performance assumes 12°C incoming water
temperature and 230V supply.
If a non-return valve is necessary for installation it must be
installed in the hot water outlet line and must NOT be fitted
in the cold inlet line before the appliance.