GSM connection is available to you with your mini Prepare the Truma iNet Box ..........6 SIM card. If there is no GSM connection, the Truma iNet Box Set up GSM connection ............7 can only be operated via Bluetooth.
– Le présent appareil est conforme aux CNR – A defective Truma iNet Box may only be re- d’Industrie Canada applicables aux appareils paired by the manufacturer or the manufac- radio exempts de licence. L’exploitation est turer’s service department.
2. Install the Truma App on the mobile terminal device. If necessary, an installed Truma App must be updated. 3. If the Truma App is to be used on several mobile terminal devices, steps 1 and 2 must be repeated for each mobile terminal device.
– Start the Truma App and open the remote control All appliances are automatically recognised. – Press the button (Figure 2 – 1) on the Truma iNet Box for approx. 1 second. The iNet-capable appliances connected to the Truma CP plus...
Several mobile terminal devices can be logged on at the Bluetooth connection (mobile phones, tablet PCs). Four mobile terminal devices can control the Truma iNet Box at the same time. The first mobile terminal device set up (administrator) remains permanently in the Truma iNet Box memory. If the maximum...
Mini-SIM card. This restricts its use to close range via Bluetooth. – If the Truma iNet Box is not used for an extended period, Truma recommends disconnecting the operating voltage to the Truma iNet Box. – If you leave your vehicle for an extended period and want...
Technical data Power supply 12 V / 24 V Voltage range min. 8 V, max. 30 V Average Power consumption 40 mA (12 V), 20 mA (24 V) SIM card type Mini-SIM (25 x 15 mm) Interfaces TIN bus (2 x TIN1 equivalent, TIN2) Bluetooth Bluetooth Class 2...
Troubleshooting guide If you encounter problems with the Truma App and / or the Truma iNet Box, we recommend checking that the app is up to date, and performing an update if necessary. In this eventuality, we also recommend a firmware update for the Truma iNet Box in accordance with the instructions in the firmware update section.
Page 10
– Repeat the set-up of the Bluetooth connection (*) Insufficient range – Check the installation of the Truma iNet Box (*) If the measures outlined here do not help, restore the factory settings. If these actions do not remedy the problem, please contact Truma Service.
Resetting to the factory settings deletes all the data. be actively connected to the Truma iNet Box. An available firmware update for the Truma iNet Box is indi- Reset all settings to the factory setting and delete all individu- cated as a notification in the Truma App.
1. Scope of manufacturer’s warranty by the authorised service partner or the manufacturer. As the manufacturer of the unit, Truma undertakes a warranty No further-reaching claims shall be permitted, especially dam- towards the consumer that covers any material and/or manu- age claims presented by the consumer or third parties.
Page 13
Truma or if the Truma control unit (e.g. Truma – Date of purchase CP plus or Truma iNet Box) has not been exclusively used for controlling Truma appliances or appliances approved by The authorised service partner or the Truma Service Centre Truma.
EU Declaration of Conformity Signed for and on behalf of : Truma Gerätetechnik GmbH & Co. KG Product Function Control unit Type Truma iNet Box Versions Truma iNet Box Manufacturer Frank Oster Truma Gerätetechnik GmbH & Co. KG Managing Director Putzbrunn, 20.06.2017...
Page 15
Should problems occur, please contact the Truma Service Centre or one of our authorised service partners (see www.truma.com). In order to avoid delays, please have the unit model and serial number ready (see type plate). Service Truma Gerätetechnik GmbH & Co. KG Wernher-von-Braun-Straße 12...