Vicon 2 Power Module / Touch Panel Inhaltsverzeichnis Sicherheitshinweise Sicherheitshinweise ............2 Die Montage und der Anschluss von elektrischen Geräten Verwendete Symbole ............2 muss grundsätzlich durch geeignetes Fachpersonal erfolgen! Verwendungszweck .............. 2 Vor Beginn der Arbeiten Einbau anweisung sorgfältig durchle-...
Diagnosestecker (Art.-Nr. C30000-00400) im System zu installieren. Touch Panel (TP) Einbaumaße Max. 1 Touch Panel kann pro installiertem Vicon 2 Bus System über einen Y-Adapter (Y) ange- schlossen werden. Das Touch Panel an einer vor Feuchtigkeit und Nässe ge- schützten Stelle einbauen. –...
Y-Adapter 12 V-Anschluss über Kabelschuh Powermodul Alde-Vicon-Interface Anschluss Ladeautomat Truma BC 630 IU Alde Raumtemperaturfühler CAN CAN-BUS Sicherung Der Ladeautomat Truma BC 630 IU muss über einen Abschlusswiderstand 120 Ω LKL-Adapter (Art.-Nr. C30000-00500) angeschlossen Shunt werden. Y-Adapter Truma Raumtemperaturfühler Anschluss Power Module – Power Module Ringkerntransformator Ü...
Für den Anschluss der Alde Heizung Compact 3010 an das an ein Power Module (PM) anschließen. Vicon 2 Bus System ist ein Interface (AVI) erforderlich. Den Y-Adapter (Art.-Nr. C30000-03300) an einer vor Feuchtig- Das Gerät über das Interface mit COM3 eines Moduls (PM) keit und Nässe geschützten Stelle (Wand oder Boden) nahe...
Schnittstellen Steuereingänge Passende Kabel und Stecker sind über Truma lieferbar. Bezeichnung I1 – I6 – gegen Masse COM1 schaltend COM2 I7, I8 – gegen Masse oder +12 V schaltend (konfigurierbar) Lastanschlüsse COM3 Anschluss über Flachsteckhülse 6,3 mm. CAN-Bus Bezeichnung COM1...
Wiring diagram 12 V voltage supply ........9 Only use suitable and fully functional tools. Automatic Charger Truma BC 630 IU connection ....9 Power Module – Power Module connection ......9 Only wire the device as specified in the supplied wiring Touch Panel connection ............
Touch Panel (TP) Installation dimensions Max. 1 Touch Panel can be connected per installed Vicon 2 bus system using a Y-adapter (Y). Install the Touch Panel in a place protected against moisture and wetness. – Produce an installation opening for the Touch-Display.
CAN CAN-BUS Fuse connection Terminating resistor 120 Ω Shunt Y-Adapter The Automatic Charger Truma BC 630 IU must be con- Truma room temperature sensor nected using a LKL adapter (part no. C30000-00500). Toroidal transformer Ü Adapter (overload protector) Power Module – Power Module connection...
An interface (AVI) is necessary to connection the Alde heating a Power Module (PM). Compact 3010 to the Vicon 2 bus system. Install the Y-adapter (part no. C30000-03300) in a place (wall Connect the device using the interface with COM3 of a or floor) protected against moisture and wetness close to module (PM).
Interfaces Control inputs The right cables and plugs are available from Truma. Name I1 – I6 – Switched to COM1 earth COM2 I7, I8 – Switched to earth or +12 V (can be configured) Load connections COM3 Connection using flat connector 6.3 mm.
Page 12
Für eine rasche Bearbeitung halten Sie bitte Gerätetyp und Fabriknummer (siehe Typenschild) bereit. In Germany, always notify the Truma Service Centre if problems are encountered; in other countries the relevant service partners should be contacted (see Truma Service Booklet or www.truma.com).