Truma devices via mobile terminal devices (e.g. smartphones, Preparing start-up .............. 4 tablet PCs). Communication is via Bluetooth or GSM. Install the Truma app on mobile terminal device ....4 Device identification .............. 4 Bluetooth communication ..........4 Bluetooth connection set-up ..........4 Bluetooth bonding ..............
Operating Instructions Display panels Safety instructions – iNet Box must not be operated unless it is in technically per- fect condition. – Repairs must be carried out immediately. Only carry out repairs yourself if the solution is described in the trouble- shooting guide of this manual.
If the Bluetooth pairing is active, the iNet Box becomes visible for 3 minutes and the blue LED (Figure 1) flashes at the same time at a frequency of 1 Hz. The name “iNet Box” Device identification appears on the mobile terminal device.
Removing the Mini-SIM card Pressing the Mini-SIM card again enables it to be removed. If there is a saved mobile terminal device within range of the iNet Box, a Bluetooth bonding to the iNet Box is automatically Setting up the GSM connection performed.
Weight approx. 500 g Clean only with a moist, lint-free cloth. Make sure that no liq- uid gets inside the iNet Box. This can cause a short circuit and External GSM antenna destruction of the iNet Box. Anntenna gain max. 5.5 dBi at 850 MHz and max. 2 dBi at 1900 MHz Subject to technical changes.
Address: Wernher-von-Braun-Str. 12, D-85640 Putzbrunn Firmware update 2. Device identification An iNet Box firmware update is indicated in the Truma app on the mobile terminal device. Transmission is via Bluetooth (fol- low the instructions in the Truma app). Type / model:...
Page 10
Truma eller Trumas serviceavdeling i landet ditt. Μπορείτε να ζητήσετε τις οδηγίες χρήσης και τοποθέτησης στη γλώσσα της χώρας σας από τον κατασκευαστή Truma ή από το σέρβις της Truma στη χώρα σας. Návod k použití a montážní návod si lze v řeči Vaší země...
Page 11
Box Installation Instructions Page E N T W U R F E N T W U R F D R A F T D R A F T 11:16, 12.03.2015...
Page 12
Box Table of Contents Symbols used ................ 2 Symbols used Installation Instructions Safety instructions ............. 3 The unit must only be installed and repaired by an Intended use ................3 expert. Scope of delivery ..............3 Accessories ................3 Dimensions ................
In other countries, the relevant regulations must be observed. Intended use The iNet Box was developed for controlling TIN-bus-capable Truma devices via mobile terminal devices (e.g. smartphones, L x W x H 147 x 96 x 40 tablet PCs). Communication is via Bluetooth or GSM.
Install the iNet Box in a location that is protected from mois- ture and humidity. For optimum transmission and reception, secure the iNet Box as high up as possible, e.g. above a win- dow and in the middle of the vehicle. At the same time, due...
Connection examples – Plug the cable (TIN-bus) into the iNet Box TIN 1/2 and con- nect it to a TIN-capable heater and/or air conditioning sys- tem (from 01.04.2015 onwards, the heater can only be operated in conjunction with a CP plus control panel).
Search for the location with the best Bluetooth reception – Establish the position of the iNet Box (safety clearance >20cm from people). – Fix the iNet Box to the wall at the established position using the two adhesive strips (the surface must be clean and smooth).
Page 18
In order to avoid delays, please have the unit model and serial number ready (see type plate). Veuillez vous adresser au centre de SAV Truma ou à un de nos partenaires de SAV agréés en cas de dysfonctionnements (voir www.truma.com).
Page 19
In order to avoid delays, please have the unit model and serial number ready (see type plate). Veuillez vous adresser au centre de SAV Truma ou à un de nos partenaires de SAV agréés en cas de dysfonctionnements (voir www.truma.com).