Danfoss VLT Aqua Drive FC 202 Operating Manual page 64

Specifications
Type designation
High/normal overload
Typical shaft output at 550 V [kW]
Typical shaft output at 550 V [hp]
Typical shaft output at 690 V [kW]
Typical shaft output at 690 V [hp]
IP20/Chassis
IP21/Type 1
IP55/Type 12
Output current
Continuous (3x525–550 V) [A]
Intermittent (60 s overload) (3x525–550 V)
[A]
Continuous (3x551–690 V) [A]
Intermittent (60 s overload) (3x551–690 V)
[A]
Continuous kVA at 550 V [kVA]
Continuous kVA at 690 V kVA]
Maximum input current
Continuous at 550 V [A]
8 8
Intermittent (60 s overload) at 550 V [A]
Continuous (at 690 V) [A]
Intermittent (60 s overload) at 690 V [A]
Additional specifications
Maximum cable cross–section
motor, brake, and load sharing [mm
Maximum cable cross–section
disconnect [mm
Estimated power loss
at rated maximum load [W (hp)]
5)
Efficiency
Table 8.16 B2/B4 Enclosure, Mains Supply 3x525–690 V AC IP20/IP21/IP55 – Chassis/NEMA 1/NEMA 12, P11K–P22K
62
1) HO
17.6
15.8
14.4
2
for mains,
2 (AWG)]
2)
for mains
2
(AWG)]
3) 150
(0.2)
4)
Danfoss A/S © 10/2016 All rights reserved.
®
VLT AQUA Drive FC 202
P11K P15K
NO HO NO
5.9 7.5 7.5 11
7.5 10 10 15
7.5 11 11 15
10 15 15 20
B4 B4
B2 B2
11 14 14.0 19.0
15.4 22.4 20.9
10 13 13.0 18.0
16 14.3 20.8 19.8
10 13.3 13.3 18.1
12 15.5 15.5 21.5
9.9 15 15.0 19.5
16.5 23.2 21.5
9 14.5 14.5 19.5
16 23.2 21.5
220 150 220
(0.3) (0.2) (0.3)
0.98 0.98
P18K P22K
HO NO HO NO
11 15 15 18.5
15 20 20 25
15 18.5 18.5 22
20 25 25 30
B4 B4
B2 B2
19.0 23.0 23.0 28.0
30.4 25.3 36.8 30.8
18.0 22.0 22.0 27.0
28.8 24.2 35.2 29.7
18.1 21.9 21.9 26.7
21.5 26.3 26.3 32.3
19.5 24.0 24.0 29.0
31.2 26.4 38.4 31.9
19.5 24.0 24.0 29.0
31.2 26.4 38.4 31.9
35, 25, 25
(2, 4, 4)
16,10,10
(6, 8, 8)
220 300 300 370
(0.3) (0.41) (0.41) (0.5)
0.98 0.98
P30K
HO NO
18.5 22
25 30
22 30
30 40
B4
B2
28.0 36.0
44.8 39.6
27.0 34.0
43.2 37.4
26.7 34.3
32.3 40.6
29.0 36.0
46.4 39.6
29.0 36.0
46.4 39.6
370 440
(0.5) (0.6)
0.98
MG20MD02