Table of Contents
Advertisement
Quick Links
Quick Installation Guide
Moxa Americas:
Toll-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa Europe:
Tel:
+49-89-3 70 03 99-0
Fax:
+49-89-3 70 03 99-99
Moxa India:
Tel:
+91-80-4172-9088
Fax:
+91-80-4132-1045
EDS-210A
Moxa EtherDevice Switch
Edition 3.0, February 2017
Technical Support Contact Information
www.moxa.com/support
2017 Moxa Inc. All rights reserved.
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax:
+86-21-5258-5505
Moxa Asia-Pacific:
Tel:
+886-2-8919-1230
Fax:
+886-2-8919-1231
P/N: 1802002100012
*1802002100012*
Advertisement
Table of Contents
Related Manuals for Moxa Technologies EDS-210A-1GTX-1GSFP-4SFP
Summary of Contents for Moxa Technologies EDS-210A-1GTX-1GSFP-4SFP
-
Page 1: Quick Installation Guide
EDS-210A Quick Installation Guide Moxa EtherDevice Switch Edition 3.0, February 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Moxa China (Shanghai office): Toll-free: 1-888-669-2872 Toll-free: 800-820-5036 Tel: 1-714-528-6777 Tel: +86-21-5258-9955 Fax: 1-714-528-6778 Fax: +86-21-5258-5505 Moxa Europe: Moxa Asia-Pacific: Tel: +49-89-3 70 03 99-0 Tel: +886-2-8919-1230 Fax:... -
Page 2: Package Checklist
• Warranty card Features High Performance Network Switching Technology • 10/100/1000BaseT(X) (EDS-210A-1GTX-1GSFP-4SFP only), 10/100BaseT(X) auto-negotiation speed, full/half duplex mode, auto MDI/MDI-X connection, and 100Base SFP slot /1000Base SFP slot. • IEEE 802.3 for 10BaseT, IEEE 802.3u for 100BaseT(X), IEEE 802.3ab for 1000BaseT, and IEEE 802.3z for 1000BaseX. - Page 3 Panel Layout of EDS-210A-1GSFP-1SFP/ EDS-210A-1GTX-1GSF-4SFP 1. Grounding screw 2. Terminal block for power input (PWR1, PWR2) and relay output 3. Power input PWR1 LED 4. Power input PWR2 LED 5. TP port’s 10/100 Mbps LED 6. TP port’s 10/100/1000 Mbps LED 7.
-
Page 4: Mounting Dimensions
Mounting Dimensions unit = mm (in) DIN-Rail Mounting The aluminum DIN-rail attachment plate should already be fixed to the back panel of the EDS when you take it out of the box. If you need to reattach the DIN-rail attachment plate, make sure the metal spring is situated towards the top, as shown in the figures below. -
Page 5: Wiring Requirements
STEP 2: Mounting the EDS on the wall requires 4 screws. Use the switch, with wall mount plates attached, as a guide to mark the correct locations of the 4 screws. The heads of the screws should be less than 6.0 mm in diameter, and the shafts should be less than 3.5 mm in diameter, as shown in the figure at the right. -
Page 6: Grounding The Moxa Etherdevice Switch
You should also pay attention to the following items: • Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point. NOTE: Do not run signal or communications wiring and power wiring in the same wire conduit. -
Page 7: Communication Connections
Communication Connections EDS-210A models have 10/100BaseT(X) Ethernet ports, 10/100/1000BaseT(X) Ethernet ports,100BaseSFP and 1000BaseSFP. 10/100BaseT(X) Ethernet Port Connection The 10/100BaseT(X) ports located on the EDS’s front panel are used to connect to Ethernet-enabled devices. Next, we show pinouts for both MDI (NIC-type) ports and MDI-X (HUB/Switch-type) ports, and also show cable wiring diagrams for straight-through and cross-over Ethernet cables. - Page 8 10 /100Base T(x) RJ45 Pinouts MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45 Signal Signal 1000BaseT RJ45 Pinouts MDI-X BI_DA+ BI_DB+ BI_DA- BI_DB- BI_DB+ BI_DA+ BI_DC+ BI_DD+ BI_DC- BI_DD- BI_DB- BI_DA- BI_DD+ BI_DC+ BI_DD- BI_DC- RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring - 8 -...
-
Page 9: Redundant Power Inputs
100Base-FX or 1000Base-X Fiber Port The Fiber ports on the EDS-210A series are SFP type slots, which support both 100Base-FX and 1000Base-X speed fiber transceiver to work properly. Moxa provides complete transceiver models for various distance requirements. Multi-mode: 1000BaseSX 0 to 550 m, 850 nm (50/125μm, 400MHz*km) 0 to 275 m, 850 nm (62.5/125μm, 200MHz*km) 1000BaseLX 0 to 1100 m, 1310 nm (50/125μm, 800MHz*km) -
Page 10: Led Indicators
LED Indicators The front panel of the Moxa EtherDevice Switch contains several LED indicators. The function of each LED is described in the table below. Color State Description Power is being supplied to power input P1 PWR1 AMBER Power is not being supplied to power input P1. -
Page 11: Auto-Negotiation And Speed Sensing
Auto-Negotiation and Speed Sensing The EDS’s RJ45 Ethernet ports independently support auto-negotiation for transmission speeds of 10 Mbps, 100 Mbps, and 1000 Mbps, with operation according to the IEEE802.3 standard. This means that some nodes could be operating at 10 Mbps, while at the same time, other nodes are operating at 100 Mbps or 1000 Mbps. -
Page 12: Regulatory Approvals
IP30 protection, metal case Dimension (W x H x 45.8 x 134 x 105 mm (1.8 x 5.28 x 4.13 in) Weight EDS-210A-1GSFP-1SFP: 520g EDS-210A-1GTX-1GSFP-4SFP: 570g Installation DIN-rail, Wall Mounting (optional kit) Environmental Operating -10 to 60°C (32 to 140°F) Temperature -40 to 75°C (-40 to 167°F) for -T models...