Gage Bilt GB713 Original Instructions Manual
Hide thumbs
Also See for GB713:
- Installation manual (14 pages) ,
- Original instructions manual (18 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gage Bilt GB713
Summary of Contents for Gage Bilt GB713
- Page 1 ORIGINAL INSTRUCTIONS GB713 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT 44766 Centre Court, Clinton Twp., MI. 48038 USA Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505 MADE in USA solutions@gagebilt.com / www.gagebilt.com...
-
Page 2: Table Of Contents
Description and Technical Specifications ..........................4 Description of Functions ................................5 Warnings ..................................... 6 Principle of Operation ................................7 How to set-up the GB713 ................................8 How to use the GB713 ................................9 Maintenance ..................................... 10 Filling and Bleeding ................................. 11 Troubleshooting .................................. -
Page 3: Eu Conformity And Warranty
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan U.S.A. +1 (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. -
Page 4: Description And Technical Specifications
90 psi (6.2 bar) air pressure at the air inlet. The GB713 installation tool operates on 90 to 100 psi (6.2-6.9 bar) of air pressure, with 90 psi (6.2 bar) providing the maximum efficiency. At 90 psi (6.2 bar) of air pressure, the GB713 does not exceed 81.5 dB(A) and consumes .30 SCF/cycle (8.50 L/cycle). -
Page 5: Description Of Functions
DESCRIPTION OF FUNCTIONS Hanger Head Cylinder Assembly Pintail Deflector Actuator Actuator Lever Assembly Handle Assembly Air Inlet Image may not reflect actual tool. GB713 Installation Tool 7/11 REV 5/22... -
Page 6: Warnings
4. Support the weight of the tool in a stand, tensioner or balancer, because a lighter grip can then be used to support the tool. GB713 Installation Tool 7/11 REV 5/22... -
Page 7: Principle Of Operation
Piston Rod Assembly moves up Piston Rod Assembly moves down Air Piston moves up Air Piston moves down Air exhaust Air exhaust Pressurized Oil Pressurized Air Unpressurized Oil Unpressurized Air Images may not reflect actual tool. GB713 Installation Tool 7/11 REV 5/22... -
Page 8: How To Set-Up The Gb713
HOW TO SET-UP THE GB713 WARNING: Only qualified and trained operators must install, adjust or use the assembly power tool for non-threaded mechanical fasteners. WARNING: Operator MUST read and understand all warnings and cautions. WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this equipment. -
Page 9: How To Use The Gb713
HOW TO USE THE GB713 WARNING: Only qualified and trained operators must install, adjust or use the assembly power tool for non-threaded mechanical fasteners. WARNING: Operator MUST read and understand all warnings and cautions. WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this equipment. -
Page 10: Maintenance
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants must be avoided. -
Page 11: Filling And Bleeding
Subtract dimension (A) from dimension (B). If stroke doesn’t check .760" (19.3 mm) min. (See figures below) follow bleeding procedure above. For your consideration, Gage Bilt offers a depth gage (Pt.# A-1935) to help simplify and more accurately check your tool stroke. Please contact Gage Bilt for more information. -
Page 12: Troubleshooting
Slide Stroke Limiter over rear Piston. (See Nose Assembly Selection Chart pg. 18 to select Stroke Limiter) Tighten End Cap onto tool. (See pg. 10 for torque setting) Images may not reflect actual tool GB713 Installation Tool 7/11 REV 5/22... -
Page 13: Overhaul
Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings. - Page 14 Thread the actuator assembly-air (704130) all the way into handle assembly (744129) with fingers. Insert and turn 5/8” wrench / adjustable wrench and snug tight approximately 1/4-1/2 turn. Re-attach actuator lever assembly (704343) including pin-slotted (400608) to the handle assembly (744129). GB713 Installation Tool 7/11 REV 5/22...
- Page 15 If ports are plugged, use needle nose pliers to grasp end of spring (744144), turning clockwise and pulling to dislodge from groove in casting. Valve spring installation tool (744251) will facilitate the proper installation of the spring (744144). Valve sleeve (743144) can be pulled out using valve sleeve removal tool (744152). GB713 Installation Tool 7/11 REV 5/22...
-
Page 16: Parts Lists
PARTS LIST GB713 Installation Tool 7/11 REV 5/22... -
Page 17: Dexron® Iii Oil Safety Data (Sds)
Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. GB713 Installation Tool 7/11 REV 5/22... -
Page 18: Nose Assembly Selection Chart
GB713 ACCESSORIES Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) NOSE ASSEMBLY SELECTION CHART Grip Gage #269G3 For CHERRYMAX® and STRAIGHT RIGHT ANGLE OFFSET CHERRYLOCK® rivets (Sold Separately) - Page 19 This page intentionally left blank. GB713 Installation Tool 7/11 REV 5/22...
-
Page 20: Accessories
Contact Gage Bilt to customize your riveter kit today. Approved Approved Accessories Cont. Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) Catcher Bag-Stem Air Bleeder Assembly Tool Stroke Depth Gage...