Hilti DCG 180-D Instruction Manual
  1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Grinder
  5. DCG 180-D
  6. Instruction manual
Hilti DCG 180-D Instruction Manual

Hilti DCG 180-D Instruction Manual

Hide thumbs Also See for DCG 180-D:
Table of Contents

Advertisement

Quick Links

Download this manual
DCG 180-D
DCG 180-P
English
Printed: 29.03.2018 | Doc-Nr: PUB / 5139411 / 000 / 02

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DCG 180-D and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hilti DCG 180-D

Summary of Contents for Hilti DCG 180-D

  • Page 1 DCG 180-D DCG 180-P English Printed: 29.03.2018 | Doc-Nr: PUB / 5139411 / 000 / 02...
  • Page 2 Printed: 29.03.2018 | Doc-Nr: PUB / 5139411 / 000 / 02...

  • Page 3: Information About The Documentation

    Information about the documentation About this documentation • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. • Observe the safety instructions and warnings in this documentation and on the product. •...
  • Page 4 ▶ Make a note of the designation and serial number printed on the identification plate in the following table. ▶ Always quote this information when you contact a Hilti representative or Hilti Service to enquire about the product.
  • Page 5 ▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. ▶ Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
  • Page 6 ▶ Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation. ▶ The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool.
  • Page 7 ▶ Do not use the power tool if it starts suddenly or with a jolt. This may indicate a fault in the electronics. Have the power tool repaired by Hilti Service right away. ▶ Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking through.
  • Page 8 ▶ Grinding discs must be stored and handled carefully in accordance with the manufacturer’s instructions. ▶ Have the tool checked by Hilti Service after breakage of a disc, if the tool has been dropped or has fallen, or in the event of other mechanical damage.
  • Page 9 Description Overview of the product Spindle lockbutton Abrasive cutting disc / abrasive grinding § disc Threaded bushing for the side handle Clamping flange with O-ring Side handle Hood Release lever for pivotable side handle Adjusting screw ∙ On/off switch & Clamping lever Wrench Spindle...
  • Page 10 Items supplied Angle grinder, guard, side handle, clamping flange, clamping nut, wrench and operating instructions. Other system products approved for use with this product can be found at your local Hilti Store or at: www.hilti.group | USA: www.hilti.com Starting current limitation The electronic starting current limiter reduces the starting current drawn by the power tool and thus prevents the mains fuse blowing.

  • Page 11: Technical Data

    The information given applies to a rated voltage of 230 V. The data may vary in the event of deviations from the rated voltage and for country-specific versions. Please refer to the power tool’s type identification plate for details of its voltage, frequency, current and input power ratings. DCG 180-D/P Rated power input 2,200 W...

  • Page 12: Preparations At The Workplace

    Noise emission values DCG 180-D/P Sound (power) level 101 dB(A) Emission sound pressure level (L 90 dB(A) Uncertainty for the sound pressure level (K 3 dB(A) Total vibration Other applications, such as cutting, may produce vibration values that deviate from the given values.
  • Page 13 Adjusting the guard or guard with cover plate 1. Release the clamping lever. 2. Rotate the guard to the required position. 3. Secure the guard by closing the clamping lever. Removing the guard or guard with cover plate 1. Release the clamping lever. 2.
  • Page 14 Fitting an accessory tool 1. Disconnect the supply cord plug from the power outlet. 2. Check that the O-ring is in place in the clamping flange and that it is undamaged. Result The O-ring is damaged. There is no O-ring in the clamping flange. ▶...
  • Page 15 Fitting an accessory tool secured with a Kwik lock nut CAUTION Risk of breakage. Heavy wear (abrasion) may cause the Kwik lock nut to break. ▶ When working with the power tool, make sure that the Kwik lock nut doesn’t come into contact with the working surface.

  • Page 16: Types Of Work

    8. Turn the accessory tool firmly by hand in a clockwise direction until the Kwik-Lock nut is tightened securely and then release the spindle lockbutton. Removing an accessory tool secured with a Kwik lock nut 1. Disconnect the supply cord plug from the power outlet. CAUTION Risk of breakage and irreparable damage.
  • Page 17 ◁ This will avoid overheating and discoloration of the workpiece and help ensure an even surface finish. Switching on DCG 180-D 1. Plug the supply cord into the power outlet. 2. Slide the on/off switch forward. 3. Press the on/off switch as far as it will go.

  • Page 18: Care And Maintenance

    Check electric tools or appliances for damage after long periods of transport or storage. Troubleshooting If the trouble you are experiencing isn’t listed in this table or you are unable to remedy the problem by yourself, please contact Hilti Service. Trouble or fault Possible cause Action to be taken The power tool doesn’t start.

  • Page 19: Manufacturer's Warranty

    Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.
  • Page 20 English Printed: 29.03.2018 | Doc-Nr: PUB / 5139411 / 000 / 02...
  • Page 21 Printed: 29.03.2018 | Doc-Nr: PUB / 5139411 / 000 / 02...
  • Page 22 Printed: 29.03.2018 | Doc-Nr: PUB / 5139411 / 000 / 02...
  • Page 23 Printed: 29.03.2018 | Doc-Nr: PUB / 5139411 / 000 / 02...
  • Page 24 Hilti = registered trademark of Hilti Corp., Schaan 20180326 Printed: 29.03.2018 | Doc-Nr: PUB / 5139411 / 000 / 02...

This manual is also suitable for:

Dcg 180-p

Table of Contents