Hilti DCG 180-D Operating Instructions Manual
Hide thumbs
Also See for DCG 180-D:
- Operating instructions manual (254 pages) ,
- Manual (244 pages) ,
- Instruction manual (24 pages)
Table of Contents
Advertisement
Quick Links
Printed: 07.07.2013 | Doc-Nr: PUB / 5139411 / 000 / 00
DCG 180-D/
DCG 180-P
Bedienungsanleitung
Operating instructions
Mode d'emploi
Manual de instrucciones
Istruzioni d'uso
Gebruiksaanwijzing
Brugsanvisning
Bruksanvisning
Bruksanvisning
Käyttöohje
Manual de instruções
Οδηγιες χρησεως
Инструкция по зксплуатации
Lietošanas pamācība
Instrukcija
Kasutusjuhend
de
en
fr
es
it
nl
da
no
sv
fi
pt
el
ru
lv
lt
et
ar
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hilti DCG 180-D
Summary of Contents for Hilti DCG 180-D
- Page 1 DCG 180-D/ DCG 180-P Bedienungsanleitung Operating instructions Mode d’emploi Manual de instrucciones Istruzioni d’uso Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Manual de instruções Οδηγιες χρησεως Инструкция по зксплуатации Lietošanas pamācība Instrukcija Kasutusjuhend Printed: 07.07.2013 | Doc-Nr: PUB / 5139411 / 000 / 00...
- Page 2 Printed: 07.07.2013 | Doc-Nr: PUB / 5139411 / 000 / 00...
- Page 3 Printed: 07.07.2013 | Doc-Nr: PUB / 5139411 / 000 / 00...
- Page 4 Printed: 07.07.2013 | Doc-Nr: PUB / 5139411 / 000 / 00...
-
Page 5: Table Of Contents
ORIGINAL OPERATING INSTRUCTIONS DCG 180‑D / DCG 180‑P angle grinder 1 These numbers refer to the corresponding illustra- It is essential that the operating instructions tions. The illustrations can be found on the fold-out cover are read before the power tool is operated for pages. -
Page 6: Description
For this application, use only synthetic resin-bonded fiber-reinforced abrasive cutting discs approved for use at a peripheral speed of at least 80 m/sec. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Working on materials hazardous to the health (e.g. asbestos) is not permissible. - Page 7 In the event of a fault in the ATC system the power tool will continue to run but at greatly reduced speed and with lower torque. The power tool must be returned to Hilti Service for servicing. 2.7 Restart interlock The power tool does not restart by itself when the switch remains pressed or is locked and the power returns after an interruption in the electric supply.
-
Page 8: Insert Tools, Accessories
Accessories for the DCG 180‑D / DCG 180‑P Designation “Kwik-Lock” clamping nut (optional) Guard with cover plate Toolbox Vacuum cleaner recommended by Hilti 4 Technical data Right of technical changes reserved. Power tool DCG 180‑D/ DCG 180‑P Rated current / power input... -
Page 9: Safety Instructions
Noise information (as perEN 60745‑1): Typical A-weighted sound power level, DCG 180-D 101 dB (A) Typical A-weighted emission sound pressure level,... - Page 10 c) Keep children and bystanders away while operat- are connected and properly used. Use of dust ing a power tool. Distractions can cause you to lose collection can reduce dust-related hazards. control. 5.1.4 Power tool use and care 5.1.2 Electrical safety a) Do not force the power tool.
- Page 11 turer. Just because the accessory can be attached could snag your clothing, pulling the accessory into to your power tool, it does not assure safe operation. your body. d) The rated speed of the accessory must be at n) Regularly clean the power tool’s air vents. The least equal to the maximum speed marked on the motor’s fan will draw the dust inside the housing power tool.
- Page 12 Never attempt to remove the is defective. Have the tool repaired at an authorized cut-off wheel from the cut while the wheel is in Hilti service center right away. motion otherwise kickback may occur.Investigate and take corrective action to eliminate the cause of h) Children must be instructed not to play with the wheel binding.
- Page 13 Hilti for wood dust Hilti Customer Service. Check extension cords and/or mineral dust together with this tool. Ensure at regular intervals and replace them if found to that the workplace is well ventilated. The use of a be damaged.
-
Page 14: Before Use
6 Before use Disconnect the supply cord plug from the power outlet. Clean the clamping flange. CAUTION The clamping flange is equipped with an O-ring. If this O-ring is missing, the clamping WARNING flange must be replaced. Never use the power tool without the guard. Fit the clamping flange onto the drive spindle. -
Page 15: Operation
Do not use the power tool if it starts with a jolt.This may be an indication that the electronic control unit is CAUTION defective. Have the tool repaired at an authorized Hilti Improve the blood circulation in your fingers by re- service center right away. -
Page 16: Care And Maintenance
To allow the power tool to be used comfortably in all (Hilti sharpening plate or sand-lime block). positions, the grip can be pivoted through 90° to the left and the right. -
Page 17: Troubleshooting
Hilti Service. 10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. -
Page 18: Manufacturer's Warranty - Tools
11 Manufacturer’s warranty - tools Hilti warrants that the tool supplied is free of defects in Additional claims are excluded, unless stringent na- material and workmanship. This warranty is valid so long tional rules prohibit such exclusion. In particular, Hilti... - Page 19 Fax:+423 / 234 29 65 www.hilti.com 1 609 929 U90 Hilti = registered trademark of Hilti Corp., Schaan W 3520 | 0313 | 00-Pos. 1 | 1 Printed in Germany © 2013 Right of technical and programme changes reserved S. E. & O 71878 / A2 Printed: 07.07.2013 | Doc-Nr: PUB / 5139411 / 000 / 00...
Need help?
Do you have a question about the DCG 180-D and is the answer not in the manual?
Questions and answers