Subscribe to Our Youtube Channel
Related Manuals for Hilti DCG 700-P
Summary of Contents for Hilti DCG 700-P
- Page 1 DCG 700-P Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções Printed: 09.12.2013 | Doc-Nr: PUB / 5164458 / 000 / 00...
- Page 2 Printed: 09.12.2013 | Doc-Nr: PUB / 5164458 / 000 / 00...
- Page 3 This Product is Certified Ce produit est homologué Producto homologado por Este produto está registrado Printed: 09.12.2013 | Doc-Nr: PUB / 5164458 / 000 / 00...
- Page 4 Printed: 09.12.2013 | Doc-Nr: PUB / 5164458 / 000 / 00...
- Page 5 Printed: 09.12.2013 | Doc-Nr: PUB / 5164458 / 000 / 00...
- Page 6 Printed: 09.12.2013 | Doc-Nr: PUB / 5164458 / 000 / 00...
-
Page 7: Table Of Contents
In these operating instructions, the designation “the Always keep these operating instructions to- power tool” always refers to the DCG 700-P angle grinder. gether with the power tool. Parts, operating controls and indicators 1 Ensure that the operating instructions are... -
Page 8: Description
Take the influences of the surrounding area into account. Do not use the power tool or appliance where there is a risk of fire or explosion. Nationally applicable industrial safety regulations must be observed. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. - Page 9 In the event of a fault in the ATC system the power tool will continue to run but at greatly reduced speed and with lower torque. The power tool must be returned to Hilti Service for servicing. 2.6 Restart interlock The power tool does not restart by itself when the switch remains pressed or is locked and the power returns after an interruption in the electric supply.
-
Page 10: Consumables
the 50 – 60 Hz range and never above 65 Hz, and the unit must be equipped with automatic voltage regulation and starting boost. Never operate other power tools or appliances from the generator or transformer at the same time. Switching other power tools or appliances on and off may cause undervoltage and / or overvoltage peaks, resulting in damage to the power tool. -
Page 11: Safety Instructions
Information about the power tool and its applications Drive spindle thread (arbor size) ⁵⁄₈"‑11 Spindle length ³⁄₄" Protection class Protection class II (double insulated) 5 Safety instructions 5.1 General Power Tool Safety Warnings 5.1.3 Personal safety a) Stay alert, watch what you are doing and use WARNING common sense when operating a power tool. - Page 12 d) Store idle power tools out of the reach of chil- wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose dren and do not allow persons unfamiliar with the power tool or these instructions to operate the or cracked wires.
- Page 13 e) Always use undamaged wheel flanges that are of sory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled correct size and shape for your selected wheel. power tool to be forced in the direction opposite of the Proper wheel flanges support the wheel thus reduc- accessory’s rotation at the point of the binding.
- Page 14 After disc breakage, or if the power tool is dropped, falls or suffers other mechanical 5.8 Additional safety instructions damage, it must be checked at a Hilti Service 5.8.1 Personal safety Center. a) Wear ear protectors. Exposure to noise can cause h) Do not use the power tool if it starts with a jolt.This...
-
Page 15: Before Use
d) When working outdoors with an electric tool 5.8.5 Personal protective equipment check to ensure that the tool is connected to the electric supply by way of a ground fault circuit interrupter (GFCI) with a rating of max. 30 mA (tripping current). -
Page 16: Operation
Do not use the power tool if it starts with a jolt.This and stalling of the insert tool. may be an indication that the electronic control unit is defective. Have the tool repaired at an authorized Hilti CAUTION service center right away. -
Page 17: Care And Maintenance
Have the power tool repaired by Hilti Service. The outer casing of the power tool is made from impact- resistant plastic. Sections of the grip are made from a WARNING synthetic rubber material. -
Page 18: Troubleshooting
Hilti Service. 10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. - Page 19 Fax:+423 / 234 29 65 www.hilti.com 1 609 92A 0JG Hilti = registered trademark of Hilti Corp., Schaan W 3521 | 1213 | 00-Pos. 3 | 1 Printed in Liechtenstein © 2013 Right of technical and programme changes reserved S. E. & O 72022 / A2 Printed: 09.12.2013 | Doc-Nr: PUB / 5164458 / 000 / 00...
Need help?
Do you have a question about the DCG 700-P and is the answer not in the manual?
Questions and answers