Hilti DCG 180-D Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Grinder
  5. DCG 180-P
  6. Operating instructions manual
Hilti DCG 180-D Operating Instructions Manual

Hilti DCG 180-D Operating Instructions Manual

Hide thumbs Also See for DCG 180-D:
Table of Contents

Advertisement

Quick Links

Download this manual
Printed: 20.11.2013 | Doc-Nr: PUB / 5139411 / 000 / 01
DCG 180-D/
DCG 180-P
Bedienungsanleitung
Operating instructions
Mode d'emploi
Manual de instrucciones
Istruzioni d'uso
Gebruiksaanwijzing
Brugsanvisning
Bruksanvisning
Bruksanvisning
Käyttöohje
Manual de instruções
Οδηγιες χρησεως
Инструкция по зксплуатации
Lietošanas pamācība
Instrukcija
Kasutusjuhend
de
en
fr
es
it
nl
da
no
sv
fi
pt
el
ru
lv
lt
et
ar

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DCG 180-D and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hilti DCG 180-D

Summary of Contents for Hilti DCG 180-D

  • Page 1 DCG 180-D/ DCG 180-P Bedienungsanleitung Operating instructions Mode d’emploi Manual de instrucciones Istruzioni d’uso Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Manual de instruções Οδηγιες χρησεως Инструкция по зксплуатации Lietošanas pamācība Instrukcija Kasutusjuhend Printed: 20.11.2013 | Doc-Nr: PUB / 5139411 / 000 / 01...
  • Page 2 Printed: 20.11.2013 | Doc-Nr: PUB / 5139411 / 000 / 01...
  • Page 3 Printed: 20.11.2013 | Doc-Nr: PUB / 5139411 / 000 / 01...
  • Page 4 Printed: 20.11.2013 | Doc-Nr: PUB / 5139411 / 000 / 01...

  • Page 5: Table Of Contents

    ORIGINAL OPERATING INSTRUCTIONS DCG 180‑D / DCG 180‑P angle grinder 1 These numbers refer to the corresponding illustra- It is essential that the operating instructions tions. The illustrations can be found on the fold-out cover are read before the power tool is operated for pages.

  • Page 6: Description

    Use only synthetic resin-bonded, fiber-reinforced grinding discs or cutting discs approved for use at a permissible peripheral speed of at least 80 m/sec. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Working on materials hazardous to the health (e.g. asbestos) is not permissible.
  • Page 7 In the event of a fault in the ATC system the power tool will continue to run but at greatly reduced speed and with lower torque. The power tool must be returned to Hilti Service for servicing. 2.7 Restart interlock The power tool does not restart by itself when the switch remains pressed or is locked and the power returns after an interruption in the electric supply.

  • Page 8: Consumables

    2.9 Using extension cords outdoors When working outdoors, use only extension cords that are approved and correspondingly marked for this application. 2.10 Using a generator or transformer This power tool may be powered by a generator or transformer when the following conditions are fulfilled: The unit must provide a power output in watts of at least twice the value printed on the type identification plate on the power tool.

  • Page 9: Safety Instructions

    Noise information (as perEN 60745‑1): Typical A-weighted sound power level, DCG 180-D 101 dB (A) Typical A-weighted emission sound pressure level,...
  • Page 10 5.1.2 Electrical safety 5.1.4 Power tool use and care a) Power tool plugs must match the outlet. Never a) Do not force the power tool. Use the correct modify the plug in any way. Do not use any ad- power tool for your application. The correct power apter plugs with earthed (grounded) power tools.
  • Page 11 d) The rated speed of the accessory must be at could snag your clothing, pulling the accessory into least equal to the maximum speed marked on the your body. power tool. Accessories running faster than their n) Regularly clean the power tool’s air vents. The rated speed can break and fly apart.
  • Page 12 Hilti for wood dust wheel binding. and/or mineral dust together with this tool. Ensure d) Do not restart the cutting operation in the work- that the workplace is well ventilated.
  • Page 13 Hilti Service Center. Under unfavorable circumstances, d) Never use the power tool without the guard.

  • Page 14: Before Use

    6 Before use To remove the guard from the power tool, follow the instructions for fitting the guard but carry out the steps in the reverse order. 6.2.2 Adjusting the guard or guard with cover plate 4 DANGER Disconnect the plug from the power source before Release the clamping lever.

  • Page 15: Operation

    The insert tool may get hot during use. Wear protective may be an indication that the electronic control unit is gloves when changing insert tools. defective. Have the tool repaired at an authorized Hilti service center right away. CAUTION In accordance with the applications for which it is de- WARNING signed, the power tool produces a high torque.

  • Page 16: Care And Maintenance

    WARNING 7.3 Rough grinding Reduce the load on the power tool by avoiding tilt- CAUTION ing the disc in the kerf when cutting. The disc may Never use abrasive cutting discs for grinding. otherwise break, or the power tool may kick back or stall. Best results are obtained when the disc maintains an CAUTION angle of 5°...

  • Page 17: Troubleshooting

    Hilti Service. 10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling.

  • Page 18: Manufacturer's Warranty - Tools

    11 Manufacturer’s warranty - tools Hilti warrants that the tool supplied is free of defects in Additional claims are excluded, unless stringent na- material and workmanship. This warranty is valid so long tional rules prohibit such exclusion. In particular, Hilti...
  • Page 19 Fax:+423 / 234 29 65 www.hilti.com 1 609 92A 0DU Hilti = registered trademark of Hilti Corp., Schaan W 3520 | 1013 | 00-Pos. 1 | 1 Printed in Germany © 2013 Right of technical and programme changes reserved S. E. & O 71878 / A3 Printed: 20.11.2013 | Doc-Nr: PUB / 5139411 / 000 / 01...

Table of Contents