Table of Contents
Advertisement
Quick Links
Model No. F802.0
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal
QUESTIONS?
If you have questions, or if parts
are damaged or missing, please
see HOW TO CONTACT
CUSTOMER CARE on the back
cover of this manual.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
OWNERʼS MANUAL
www.freemotionfitness.com
Advertisement
Table of Contents
Related Manuals for Freemotion Epic F802.0
Summary of Contents for Freemotion Epic F802.0
- Page 1 OWNERʼS MANUAL Model No. F802.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? If you have questions, or if parts are damaged or missing, please see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual.
-
Page 2: Table Of Contents
HOW TO CONTACT CUSTOMER CARE ..........Back Cover FREEMOTION is a registered trademark of ICON IP, Inc. -
Page 3: Important Precautions
To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your strength equipment before using your strength equipment. FreeMotion Fitness assumes no responsibility for personal injury or property damage sustained by or through the use of this product. -
Page 4: Warning Decal Placement
WARNING DECAL PLACEMENT This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible, see the back cover of this manual and request a free replacement decal. Apply the decal in the location shown. Note: The decal(s) may not be shown at actual size. -
Page 5: Before You Begin
BEFORE YOU BEGIN Thank you for selecting the FREEMOTION EPIC™ of this manual. To help us assist you, note the product ® LAT/HIGH ROW strength equipment. With unrestricted model number and serial number before contacting us. motion, you can work your bodyʼs muscle groups the... -
Page 6: Part Identification Chart
PART IDENTIFICATION CHART Refer to the drawings below to identify small parts used for assembly. The number in parentheses by each draw- ing is the key number of the part, from the PART LIST near the end of this manual. The number following the parentheses is the quantity needed for assembly. -
Page 7: Assembly
ASSEMBLY • Assembly requires two persons. • The following tools (not included) are required for assembly: • Because of its weight and size, assemble the one adjustable wrench strength equipment in the location where it will be used. Make sure that there is enough clearance one Phillips screwdriver around the strength equipment. -
Page 8: Frame (1) As Shown
3. Attach the Connecting Frame (38) to the Main Frame (68) with three M10 x 35mm Socket Screws (71) and three M10 Washers (31). Do not tighten the Socket Screws yet. 4. Orient the Tower Frame (1) as shown, and set it near the Connecting Frame (38). -
Page 9: Frame (1) As Shown
5. Insert the Long Cable (40) through the Tower Frame (1) as shown. Attach the Connecting Frame (38) to the Tower Frame (1) with four M10 x 35mm Socket Screws (71) and four M10 Washers (31). Start all four Socket Screws, and then tighten them. - Page 10 8. Loosen the two M8 x 35mm Set Screws (19) a 19 18 few complete turns; it is not necessary to remove the Set Screws. Look under the top of the Tower Frame (1) and remove the two 25mm Snap Rings (39) from the two Weight Guide Bushings (18).
- Page 11 10. Orient the Top Weight (9) and the Drop-down Weight (10) as shown. 19 18 Slide the Top Weight (9), the two Upper Weight Bumpers (16), the Drop-down Weight (10), and the two 25mm Snap Rings (39) onto the Weight Guides (7).
-
Page 12: Pound Weights (44)
12. Tighten the end of the Long Cable (40) into the Weight Selector (11) until the Top Weight (9) is lifted off the 10-pound Weights (44). Then, loosen the end of the Long Cable until the Top Weight just rests on the 10-pound Weights. Then, tighten the jam nut on the end of the Long Cable (40) against the Weight Selector (11). - Page 13 14. Slide the two Shrouds (36) with the Shroud Panel (46) downward into the two strips of Outer Trim (5) on the back of the Tower Frame (1). 15. Slide the two remaining Shrouds (36) downward into the two strips of Outer Trim (5) on the front of the Tower Frame (1).
- Page 14 16. Orient the Tower Cap (2) as shown. Slide the Tower Cap (2) downward onto the Tower Frame (1). Attach the Tower Cap with two M4 x 13mm Self-tapping Screws (27). 17. Tighten the end of the Long Cable (40) several turns into the Large Pulley Bracket (41).
- Page 15 18. Attach a 25mm Snap Ring (39) to one end of the Arm Axle (59). Identify the Right Arm (47). Have a second person hold the round tube on the Right Arm (47) and two Plastic Washers (54) inside the bracket on the Main Frame (68). Insert the Arm Axle (59) into the bracket, the Plastic Washers, and the round tube.
- Page 16 21. Remove the two indicated M10 x 35mm Socket Screws (71) and M10 Washers (31) from the Main Frame (68). Attach the two Joint Bearings (80) on the ends of the Short Cable (42) to the Main Frame (68) with the two M10 x 35mm Socket Screws (71) and M10 Washers (31) that you just removed.
- Page 17 24. Orient the Thigh Pad Frame (45) as shown. Press the Latch (53), insert the Thigh Pad Frame (45) into the Main Frame (68), and then release the Latch. Move the Thigh Pad Frame upward and downward slightly to make sure that the Latch is engaged in one of the adjustment holes in the Thigh Pad Frame.
-
Page 18: Adjustment
ADJUSTMENT This section explains how to adjust the strength equipment. Make sure all that parts are properly tightened each time the strength equipment is used. Replace any worn parts immediately. ADJUSTING THE RESISTANCE To change the amount of resistance, insert the weight pin into the desired weight. -
Page 19: Maintenance And Troubleshooting
Personnel must also record and report any accident. To maintain the strength equipmentʼs warranty, use only FREEMOTION parts for repair or replacement. If there are any questions or concerns, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual. - Page 20 Cable Adjustment MONTHLY MAINTENANCE To determine whether each cable is properly adjusted, Grips slowly raise and lower the top weight by performing one repetition. Check the grips and replace them if needed. Weight Guide Lubrication If the cable is loose, the top weight will not be lifted immediately when you begin the repetition.
-
Page 21: Cable Diagram
CABLE DIAGRAM The diagram below shows the correct route of each cable. The numbers in each drawing show the correct route of that cable. Use the diagram to make sure that each cable is correctly routed. If a cable is not correctly routed, the strength equipment will not function properly and damage may occur. - Page 22 NOTES...
- Page 23 NOTES...
- Page 24 NOTES...
-
Page 25: Part List
PART LIST Model No. F802.0 R1110A Key No. Qty. Description Key No. Qty. Description Tower Frame Anchor Strap Tower Cap 10-pound Weight Rear Shroud Base Thigh Pad Frame Front Shroud Base Shroud Panel Outer Trim Right Arm Small Pulley Bracket Large Spring Weight Guide Handle Collar... -
Page 26: Exploded Drawing
EXPLODED DRAWING A Model No. F802.0 R1110A... - Page 27 EXPLODED DRAWING B Model No. F802.0 R1110A...
-
Page 28: How To Contact Customer Care
PART LIST and the EXPLODED DRAWING near the end of this manual). In the United States and Canada Call: 1-800-201-2109, Mon.–Fri. 8 a.m.–5 p.m. MT Write: FreeMotion Fitness 1500 South 1000 West Logan, UT 84321-9813 United States Outside the United States and Canada Call: 001-435-786-3521 Email: intlcustomercare@freemotionfitness.com...