Freemotion F801.0 Owner's Manual
  1. Manuals
  2. Brands
  3. Freemotion Manuals
  4. Fitness Equipment
  5. EPIC F801.0
  6. Owner's manual

Freemotion F801.0 Owner's Manual

Leg extension
Hide thumbs Also See for F801.0:
Table of Contents

Advertisement

Quick Links

Model No. F801.0
Serial No.
Write the serial number in the
space above for reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts
are damaged or missing, please
see HOW TO CONTACT
CUSTOMER CARE on the back
cover of this manual.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
OWNER'S MANUAL
www.freemotionfitness.com

Advertisement

Table of Contents
loading

Related Manuals for Freemotion F801.0

Summary of Contents for Freemotion F801.0

  • Page 1 Model No. F801.0 Serial No. OWNER’S MANUAL Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? If you have questions, or if parts are damaged or missing, please see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual.

  • Page 2: Table Of Contents

    HOW TO CONTACT CUSTOMER CARE ..........Back Cover FREEMOTION is a registered trademark of ICON IP, Inc.

  • Page 3: Important Precautions

    To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your strength equipment before using your strength equipment. FreeMotion Fitness assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

  • Page 4: Warning Decal Placement

    WARNING DECAL PLACEMENT This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible, see the back cover of this manual and request a free replacement decal. Apply the decal in the location shown. Note: The decal(s) may not be shown at actual size.

  • Page 5: Before You Begin

    BEFORE YOU BEGIN Thank you for selecting the FREEMOTION of this manual. To help us assist you, note the product ® EXTENSION strength equipment. With unrestricted model number and serial number before contacting us. motion, you can work your body’s muscle groups the...

  • Page 6: Part Identification Chart

    PART IDENTIFICATION CHART Use the drawings below to identify small parts used for assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the parenthe- ses is the quantity needed for assembly.

  • Page 7: Assembly

    ASSEMBLY • Assembly requires two persons. • The following tools (not included) are required for assembly: • Because of its weight and size, assemble the strength equipment in the location where it will be • one adjustable wrench used. Make sure that there is enough clearance around the strength equipment.
  • Page 8 2. Orient the Tower Frame (1) as shown. Have a second person hold the Tower Frame to pre- vent it from falling until you complete step 4. Remove the two M10 x 30mm Socket Screws (30), the two M10 Washers (31), and the Pulley Bracket (6) from the back of the Tower Frame (1).
  • Page 9 4. Route the Cable (40) upward through the Pulley Bracket (6). Attach the Large Pulley (24) inside the Pulley Bracket with the M10 x 50mm Socket Bolt (29), the two M10 Washers (31), and the M10 Locknut (32) that you removed in step 2. Then, attach the Pulley Bracket (6) to the Tower Frame (1) with the two M10 x 30mm Socket Screws (30) and the two M10 Washers (31) that...
  • Page 10 6. Pull the Drop-down Weight Knob (20) and slide the Drop-down Weight (10) downward on the Weight Guides (7). Next, loosen the two M8 x 35mm Set Screws (19) a few complete turns; it is not necessary to remove the Set Screws. Look under the top of the Tower Frame (1) and remove the two 25mm Snap Rings (39) from the two Weight Guide Bushings (18).
  • Page 11 8. Orient the Top Weight (9) and the Drop-down Weight (10) as shown. Slide the Top Weight (9), the two Upper Weight Bumpers (16), the Drop-down Weight (10), and the two 25mm Snap Rings (39) onto the Weight Guides (7). Next, insert the two Weight Guide Bushings (18) into the Tower Frame (1), and slide them onto the upper ends of the Weight Guides (7).
  • Page 12 10. Remove the jam nut from the end of the Cable (40). Next, slide the tether on the Weight Pin (12) onto the end of the Cable. Then, finger tighten the jam nut onto the end of the Cable. Tighten the end of the Cable (40) into the Weight Selector (11) until the Top Weight (9) is lifted off the 10-pound Weights (44).
  • Page 13 12. Attach a 25mm Snap Ring (39) to one end of the Long Pivot Axle (59). Identify the Pivot Arm (52) and orient it as shown. Have a second person hold the round tube on the Pivot Arm (52) and two Plastic Washers (56) inside the bracket on the Connecting Frame (38).
  • Page 14 14. Attach the Counterweight (45) to the Pivot Arm (52) with two M10 x 85mm Socket Bolts (98), four M10 Washers (31), and two M10 Locknuts (32). 15. Loosen the two M6 x 15mm Socket Screws (88) in the Bar Clamp (87) on the indicated end of the Pad Bar (60);...
  • Page 15 16. Press the end of the Cable (40) as far as pos- sible into the socket on the Cam (48). Next, loosen the two M6 x 15mm Socket Screws (88) in the Bar Clamp (87) on the indicated end of the Pad Bar (60); it is not necessary to remove the Socket Screws.
  • Page 16 18. Attach the Seat (62) to the Base (72) and the Connecting Frame (38) with three M8 x 55mm Socket Screws (99) and three M8 Washers (80). 19. Attach the Backrest (61) to the Backrest Frame (47) with two M8 x 25mm Socket Screws (75) and two M8 Washers (80).
  • Page 17 21. Note: The parts shown in this step may be preassembled. Look at the four Shrouds (36), and identify the two Shrouds that have strips of Inner Trim (37) and the two Shrouds that do not. Slide the Shroud Panel (46) downward onto the two Shrouds (36) that do not have strips of Inner Trim (37).
  • Page 18 23. Slide the two remaining Shrouds (36) downward into the two strips of Outer Trim (5) on the front of the Tower Frame (1). 24. Orient the Tower Cap (2) as shown. Slide the Tower Cap (2) downward onto the Tower Frame (1).

  • Page 19: Adjustment

    ADJUSTMENT This section explains how to adjust the strength equipment. Make sure that all parts are properly tightened each time the strength equipment is used. Replace any worn parts immediately. ADJUSTING THE RESISTANCE To change the amount of resistance, insert the weight pin into the desired weight.
  • Page 20 ADJUSTING THE BACKREST Backrest Backrest To adjust the backrest, press the adjustment lever, Frame move the backrest frame forward or backward to the desired position, and then release the adjust- ment lever into an adjustment hole in the backrest frame. Make sure that the adjustment lever is firmly engaged in an adjustment hole.

  • Page 21: Maintenance And Troubleshooting

    Personnel must also record and report any accident. To maintain the strength equipment’s warranty, use only FREEMOTION parts for repair or replacement. If there are any questions or concerns, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual.
  • Page 22 Cable Adjustment MONTHLY MAINTENANCE To determine whether each cable is properly adjusted, slowly raise and lower the top weight by performing Grips one repetition. Check the grips and replace them if needed. If the cable is loose, the top weight will not be lifted Weight Guide Lubrication immediately when you begin the repetition.

  • Page 23: Cable Diagram

    CABLE DIAGRAM The diagram below shows the correct route of the cable. Use the diagram to make sure that the cable is correctly routed. If the cable is not correctly routed, the strength equipment will not function properly and damage may occur.

  • Page 24: Part List

    PART LIST Model No. F801.0 R0312A Key No. Qty. Description Key No. Qty. Description Tower Frame Pivot Leg Tower Cap Pivot Arm Rear Shroud Base Short Pivot Axle Front Shroud Base Handgrip Collar Outer Trim Handgrip Cap Pulley Bracket Plastic Washer...
  • Page 25 Key No. Qty. Description Key No. Qty. Description M10 x 20mm Socket Screw M6 x 15mm Flat Head Screw M8 x 40mm Socket Screw Bearing Cover Shroud Bracket – Owner’s Manual Note: Specifications are subject to change without notice. For information about ordering replacement parts, see the back cover of this manual.

  • Page 26: Exploded Drawing A

    EXPLODED DRAWING A Model No. F801.0 R0312A...
  • Page 27 EXPLODED DRAWING B Model No. F801.0 R0312A...

  • Page 28: How To Contact Customer Care

    LIST and the EXPLODED DRAWING near the end of this manual). In the United States and Canada Call: 1-800-201-2109, Mon.–Fri. 8 a.m.–5 p.m. MT Write: FreeMotion Fitness 1500 South 1000 West Logan, UT 84321-9813 United States Outside the United States and Canada Call: 001-435-786-3521 Email: intlcustomercare@freemotionfitness.com...

Table of Contents