Table of Contents
Advertisement
Quick Links
Model No. F803.0
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal
QUESTIONS?
If you have questions, or if parts
are damaged or missing, please
see HOW TO CONTACT
CUSTOMER CARE on the back
cover of this manual.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
OWNERʼS MANUAL
www.freemotionfitness.com
Advertisement
Table of Contents
Related Manuals for Freemotion EPIC F803.0
Summary of Contents for Freemotion EPIC F803.0
- Page 1 OWNERʼS MANUAL Model No. F803.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? If you have questions, or if parts are damaged or missing, please see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual.
-
Page 2: Table Of Contents
HOW TO CONTACT CUSTOMER CARE ..........Back Cover FREEMOTION is a registered trademark of ICON IP, Inc. -
Page 3: Important Precautions
To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your strength equipment before using your strength equipment. FreeMotion Fitness assumes no responsibility for personal injury or property damage sustained by or through the use of this product. -
Page 4: Warning Decal Placement
WARNING DECAL PLACEMENT This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible, see the back cover of this manual and request a free replacement decal. Apply the decal in the location shown. Note: The decal(s) may not be shown at actual size. -
Page 5: Before You Begin
BEFORE YOU BEGIN Thank you for selecting the FREEMOTION EPIC™ of this manual. To help us assist you, note the product ® LEG CURL strength equipment. With unrestricted model number and serial number before contacting us. motion, you can work your bodyʼs muscle groups the... -
Page 6: Part Identification Chart
PART IDENTIFICATION CHART Refer to the drawings below to identify small parts used for assembly. The number in parentheses by each draw- ing is the key number of the part, from the PART LIST near the end of this manual. The number following the parentheses is the quantity needed for assembly. -
Page 7: Assembly
ASSEMBLY • Assembly requires two persons. • The following tools (not included) are required for assembly: • Because of its weight and size, assemble the one adjustable wrench strength equipment in the location where it will be used. Make sure that there is enough clearance one Phillips screwdriver around the strength equipment. -
Page 8: And Four M8 Washers (76). Do Not Tighten The
2. Attach the upper end of the Connecting Frame (38) to the Main Frame (68) with two M10 x 30mm Socket Screws (30) and two M10 Washers (31). Do not tighten the Socket Screws yet. 3. Attach the Handle Frame (82) to the Connecting Frame (38) with four M8 x 15mm Screws (106) and four M8 Washers (76). - Page 9 4. Have a second person hold the end of the Pivot Arm (83) and two Plastic Washers (54) inside the bracket on the Connecting Frame (38). Insert the Medium Axle (78) through the bracket, through the Plastic Washers (54), and through the Pivot Arm (83).
- Page 10 6. Attach a 25mm Snap Ring (39) to one end of the Short Axle (80). Have a second person hold the end of the Pivot Leg (93) and two Plastic Washers (54) inside the bracket on the Pivot Arm (83). Pull the indi- cated Adjustment Knob (99), and insert the Large Adjustment Pin (104) into one of the holes in the Pivot Leg Bracket (85).
- Page 11 8. Remove all parts (31, 79, and 96) from the pul- ley bracket on the Connecting Frame (38). Orient the Cable (40) as shown, and insert it through the Connecting Frame (38) and through the pulley bracket as shown. Attach the V-pulley (96) inside the pulley bracket on the Connecting Frame (38) with the M10 x 65mm Socket Bolt (79) and the M10 Large...
- Page 12 10. Note: If the two Thigh Pads (56) are already attached, go to step 11. If the Thigh Pads are not attached, follow the instructions in this step. Attach a Thigh Pad (56) to one of the Large Pad Plates (57) on the Thigh Pad Bracket (45) with two M8 x 25mm Screws (77).
- Page 13 12. Attach the Seat (52) to the Main Frame (68) with two M8 x 25mm Socket Screws (75), an M8 x 55mm Socket Screw (107), and three M8 Washers (76). 13. Orient the Tower Frame (1) as shown, and set it near the Connecting Frame (38).
- Page 14 14. Insert the Cable (40) through the Tower Frame (1) as shown. Attach the Connecting Frame (38) to the Tower Frame (1) with four M10 x 35mm Socket Screws (71) and four M10 Washers (31). See step 1. Tighten the four M10 x 35mm Socket Screws (71).
- Page 15 17. Loosen the two M8 x 35mm Set Screws (19) a few complete turns; it is not necessary to 19 18 remove the Set Screws. Look under the top of the Tower Frame (1) and remove the two 25mm Snap Rings (39) from the two Weight Guide Bushings (18).
- Page 16 19. Orient the Top Weight (9) and the Drop-down Weight (10) as shown. 19 18 Slide the Top Weight (9), the two Upper Weight Bumpers (16), the Drop-down Weight (10), and the two 25mm Snap Rings (39) onto the Weight Guides (7).
- Page 17 21. Tighten the end of the Cable (40) into the Weight Selector (11) until the Top Weight (9) is lifted off the 10-pound Weights (44). Then, loosen the end of the Cable until the Top Weight just rests on the 10-pound Weights. Then, tighten the jam nut on the end of the Cable (40) against the Weight Selector (11).
- Page 18 23. Slide the two Shrouds (36) with the Shroud Panel (46) downward into the two strips of Outer Trim (5) on the back of the Tower Frame (1). 24. Slide the two remaining Shrouds (36) downward into the two strips of Outer Trim (5) on the front of the Tower Frame (1).
- Page 19 25. Orient the Tower Cap (2) as shown. Slide the Tower Cap (2) downward onto the Tower Frame (1). Attach the Tower Cap with two M4 x 13mm Self-tapping Screws (27). 26. Attach the Counterweight (64) to the Pivot Arm (83) with two M10 x 70mm Socket Bolts (67), four M10 Washers (31), and two M10 Locknuts (32).
-
Page 20: Adjustment
ADJUSTMENT This section explains how to adjust the strength equipment. Make sure all that parts are properly tightened each time the strength equipment is used. Replace any worn parts immediately. ADJUSTING THE RESISTANCE To change the amount of resistance, insert the weight pin into the desired weight. - Page 21 ADJUSTING THE BACKREST Backrest To adjust the position of the backrest, press the latch, move the backrest forward or backward, and then release the latch. Move the backrest forward and backward slightly to make sure that the latch is engaged in one of the adjustment holes in the backrest bracket (not shown).
-
Page 22: Maintenance And Troubleshooting
Personnel must also record and report any accident. To maintain the strength equipmentʼs warranty, use only FREEMOTION parts for repair or replacement. If there are any questions or concerns, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual. -
Page 23: Cable Diagram
Cable Adjustment To determine whether each cable is properly adjusted, Cable slowly raise and lower the top weight by performing Jam Nut one repetition. Top Weight If the cable is loose, the top weight will not be lifted immediately when you begin the repetition. Weight Selector If the cable is too tight, the top weight will not rest on the weight beneath it when you complete the repeti-... -
Page 24: Part List
PART LIST Model No. F803.0 R1210A Key No. Qty. Description Key No. Qty. Description Tower Frame Pad Bushing Tower Cap Seat Rear Shroud Base Latch Front Shroud Base Plastic Washer Outer Trim Frame Bushing Pulley Bracket Thigh Pad Weight Guide Large Pad Plate 20-pound Weight Small Pad Plate... - Page 25 Key No. Qty. Description Key No. Qty. Description Small Pin Spring M8 x 15mm Screw Large Pin Spring M8 x 55mm Socket Screw Small Adjustment Pin M10 x 18mm Socket Screw Large Adjustment Pin Bungee M8 x 15mm Socket Screw –...
-
Page 26: Exploded Drawing
EXPLODED DRAWING A Model No. F803.0 R1210A... - Page 27 EXPLODED DRAWING B Model No. F803.0 R1210A...
-
Page 28: How To Contact Customer Care
PART LIST and the EXPLODED DRAWING near the end of this manual). In the United States and Canada Call: 1-800-201-2109, Mon.–Fri. 8 a.m.–5 p.m. MT Write: FreeMotion Fitness 1500 South 1000 West Logan, UT 84321-9813 United States Outside the United States and Canada Call: 001-435-786-3521 Email: intlcustomercare@freemotionfitness.com...