Table of Contents
Advertisement
Quick Links
Model No. F801.0
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal
QUESTIONS?
If you have questions, or if parts
are damaged or missing, please
see HOW TO CONTACT
CUSTOMER CARE on the back
cover of this manual.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
OWNERʼS MANUAL
www.freemotionfitness.com
Advertisement
Table of Contents
Related Manuals for Freemotion EPIC F801.0
Summary of Contents for Freemotion EPIC F801.0
- Page 1 OWNERʼS MANUAL Model No. F801.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? If you have questions, or if parts are damaged or missing, please see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual.
-
Page 2: Table Of Contents
HOW TO CONTACT CUSTOMER CARE ..........Back Cover FREEMOTION is a registered trademark of ICON IP, Inc. -
Page 3: Important Precautions
To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your strength equipment before using your strength equipment. FreeMotion Fitness assumes no responsibility for personal injury or property damage sustained by or through the use of this product. -
Page 4: Warning Decal Placement
WARNING DECAL PLACEMENT This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible, see the back cover of this manual and request a free replacement decal. Apply the decal in the location shown. Note: The decal(s) may not be shown at actual size. -
Page 5: Before You Begin
BEFORE YOU BEGIN Thank you for selecting the FREEMOTION EPIC™ of this manual. To help us assist you, note the product ® LEG EXTENSION strength equipment. With unre- model number and serial number before contacting us. stricted motion, you can work your bodyʼs muscle... -
Page 6: Part Identification Chart
PART IDENTIFICATION CHART Refer to the drawings below to identify small parts used for assembly. The number in parentheses by each draw- ing is the key number of the part, from the PART LIST near the end of this manual. The number following the parentheses is the quantity needed for assembly. -
Page 7: Assembly
ASSEMBLY • Assembly requires two persons. • The following tools (not included) are required for assembly: • Because of its weight and size, assemble the one adjustable wrench strength equipment in the location where it will be used. Make sure that there is enough clearance one Phillips screwdriver around the strength equipment. - Page 8 2. Orient the Tower Frame (1) as shown. Have a second person hold the Tower Frame to pre- vent it from falling until you complete step 3. Remove the two M10 x 30mm Socket Patch Screws (30), the two M10 Washers (31), and the Pulley Bracket (6) from the back of the Tower Frame (1).
-
Page 9: Bracket (6). Attach The Large Pulley (24) Inside
4. Route the Cable (40) upward through the Pulley Bracket (6). Attach the Large Pulley (24) inside the Pulley Bracket with the M10 x 50mm Socket Bolt (29), the two M10 Washers (31), and the M10 Locknut (32) that you removed in step 2. Then, attach the Pulley Bracket (6) to the Tower Frame (1) with the two M10 x 30mm Socket Patch Screws (30) and the two M10 Washers... - Page 10 6. Loosen the two M8 x 35mm Set Screws (19) a few complete turns; it is not necessary to 19 18 remove the Set Screws. Look under the top of the Tower Frame (1) and remove the two 25mm Snap Rings (39) from the two Weight Guide Bushings (18).
- Page 11 8. Orient the Top Weight (9) and the Drop-down Weight (10) as shown. 19 18 Slide the Top Weight (9), the two Upper Weight Bumpers (16), the Drop-down Weight (10), and the two 25mm Snap Rings (39) onto the Weight Guides (7).
- Page 12 10. Tighten the end of the Cable (40) into the Weight Selector (11) until the Top Weight (9) is lifted off the Weights (8, 44). Then, loosen the end of the Cable until the Top Weight just rests on the Weights. Then, tighten the jam nut on the end of the Cable (40) against the Weight Selector (11).
- Page 13 12. Attach a 25mm Snap Ring (39) to one end of the Cam Pivot Axle (59). Identify the Pivot Arm (52) and orient it as shown. Have a second person hold the round tube on the Pivot Arm (52) and two Plastic Washers (56) inside the bracket on the Connecting Frame (38).
- Page 14 14. Attach a 25mm Snap Ring (39) to one end of the Pivot Axle (53). Identify the Pivot Leg (51) and orient it as shown. Have a second person hold the round tube on the Pivot Leg (51) and two Plastic Washers (56) inside the bracket on the Pivot Arm (52).
- Page 15 16. Identify the Left and Right Handlebars (83, 86), and orient them as shown. Attach the Left and Right Handlebars (83, 86) to the Base (72) with two M10 x 95mm Socket Bolts (97), four M10 Washers (31), and two M10 Locknuts (32).
- Page 16 18. Attach the Backrest (61) to the Backrest Frame (47) with two M8 x 25mm Socket Screws (75) and two M8 Washers (80). 19. Remove the M10 x 18mm Stop Screw (70) from the Base (72). Press the Adjustment Lever (66) on the Base (72), insert the Backrest Frame (47) into the Base, and then release the Adjustment Lever into one of the adjustment holes in the Backrest...
- Page 17 20. Look at the four Shrouds (36), and find the two Shrouds that have strips of Inner Trim (37) and the two Shrouds that do not. Slide the Shroud Panel (46) downward onto the two Shrouds (36) that do not have strips of Inner Trim (37).
- Page 18 22. Slide the two remaining Shrouds (36) downward into the two strips of Outer Trim (5) on the front of the Tower Frame (1). 23. Slide the Tower Cap (2) downward onto the Tower Frame (1). Attach the Tower Cap with two M4 x 13mm Self-tapping Screws (27).
-
Page 19: Adjustment
ADJUSTMENT This section explains how to adjust the strength equipment. Make sure all that parts are properly tightened each time the strength equipment is used. Replace any worn parts immediately. ADJUSTING THE RESISTANCE To change the amount of resistance, insert the weight pin into the desired weight. - Page 20 ADJUSTING THE BACKREST Backrest Backrest To adjust the backrest, press the adjustment lever, Frame move the backrest frame forward or backward to the desired position, and then release the adjust- ment lever into an adjustment hole in the backrest frame. Make sure that the adjustment lever is firmly engaged in an adjustment hole.
-
Page 21: Maintenance And Troubleshooting
Personnel must also record and report any accident. To maintain the strength equipmentʼs warranty, use only FREEMOTION parts for repair or replacement. If there are any questions or concerns, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual. - Page 22 Cable Adjustment MONTHLY MAINTENANCE To determine whether the cables are properly Grips adjusted, slowly raise and lower the top weight by per- forming one repetition. Check the grips and replace them if needed. Weight Guide Lubrication If the cables are loose, the top weight will not be lifted immediately when you begin the repetition.
-
Page 23: Cable Diagram
CABLE DIAGRAM The diagram below shows the correct route of each cable. The numbers in each drawing show the correct route of that cable. Use the diagram to make sure that each cable is correctly routed. If a cable is not correctly routed, the strength equipment will not function properly and damage may occur. -
Page 24: Part List
PART LIST Model No. F801.0 R1210A Key No. Qty. Description Key No. Qty. Description Tower Frame Shroud Panel Tower Cap Backrest Frame Rear Shroud Base Front Shroud Base Cam Selector Plate Outer Trim Pivot Leg Selector Plate Pulley Bracket Pivot Leg Weight Guide Pivot Arm 20-pound Weight... - Page 25 Key No. Qty. Description Key No. Qty. Description Small Pin Spring M10 x 85mm Socket Bolt/Screw Large Pin Spring M8 x 55mm Socket Screw Small Pin M6 Locknut Large Pin M10 x 20mm Patch Socket Screw Plate Spacer M8 x 40mm Patch Socket Screw M8 x 20mm Patch Socket Screw –...
-
Page 26: Exploded Drawing
EXPLODED DRAWING A Model No. F801.0 R1210A 13 12... - Page 27 EXPLODED DRAWING B Model No. F801.0 R1210A...
-
Page 28: How To Contact Customer Care
PART LIST and the EXPLODED DRAWING near the end of this manual). In the United States and Canada Call: 1-800-201-2109, Mon.–Fri. 8 a.m.–5 p.m. MT Write: FreeMotion Fitness 1500 South 1000 West Logan, UT 84321-9813 United States Outside the United States and Canada Call: 001-435-786-3521 Email: intlcustomercare@freemotionfitness.com...