Yamaha XG250 Service Manual page 31

Item
Timing chain guide (intake side)
Oil filter element cover (under)
Oil delivery pipe
Oil delivery pipe and cylinder
Oil pump assembly
Oil pump assembly (crankcase)
Air filter case
Carburetor joint clamp screw
Air cut-off valve
Exhaust pipe nut
Muffler joint
Muffler (front)
Muffler (rear)
Left crankcase cover
Right crankcase cover
Crankcase
Oil drain bolt
Ground lead, clutch cable holder
Neutral switch lead clamp
Starter idle gear cover
Starter clutch
Primary drive gear nut
Clutch boss nut
Clutch spring
Push lever adjusting screw locknut
Push lever shaft
Drive sprocket nut
Stopper lever
Neutral switch
Starter motor
Stator coil
Pickup coil
Thread
Q'ty
size
M6 1 8 Nm (0.8 m•kg, 5.8 ft•lb)
M6 3 10 Nm (1.0 m•kg, 7.2 ft•lb)
M10 2 20 Nm (2.0 m•kg, 14 ft•lb)
M8 2 17 Nm (1.7 m•kg, 12 ft•lb)
M6 2 7 Nm (0.7 m•kg, 5.1 ft•lb)
M6 1 6 Nm (0.6 m•kg, 4.3 ft•lb)
M6 3 7 Nm (0.7 m•kg, 5.1 ft•lb)
M4 1 2 Nm (0.2 m•kg, 1.4 ft•lb)
M6 1 7 Nm (0.7 m•kg, 5.1 ft•lb)
M8 2 18 Nm (1.8 m•kg, 13 ft•lb)
M8 1 20 Nm (2.0 m•kg, 14 ft•lb)
M8 1 40 Nm (4.0 m•kg, 29 ft•lb)
M8 1 42 Nm (4.2 m•kg, 30 ft•lb)
M6 1 7 Nm (0.7 m•kg, 5.1 ft•lb)
M6 14 10 Nm (1.0 m•kg, 7.2 ft•lb)
M6 12 10 Nm (1.0 m•kg, 7.2 ft•lb)
M12 1 20 Nm (2.0 m•kg, 14 ft•lb)
M6 1 10 Nm (1.0 m•kg, 7.2 ft•lb)
M6 1 7 Nm (0.7 m•kg, 5.1 ft•lb)
M6 3 8 Nm (0.8 m•kg, 5.8 ft•lb)
M8 3 30 Nm (3.0 m•kg, 22 ft•lb)
M16 1 80 Nm (8.0 m•kg, 58 ft•lb)
M16 1 75 Nm (7.5 m•kg, 54 ft•lb)
M6 5 8 Nm (0.8 m•kg, 5.8 ft•lb)
M6 1 8 Nm (0.8 m•kg, 5.8 ft•lb)
M8 1 12 Nm (1.2 m•kg, 8.6 ft•lb)
M18 1 110 Nm (11.0 m•kg, 80 ft•lb)
M6 1 10 Nm (1.0 m•kg, 7.2 ft•lb)
M10 1 20 Nm (2.0 m•kg, 14 ft•lb)
M6 2 10 Nm (1.0 m•kg, 7.2 ft•lb)
M6 3 7 Nm (0.7 m•kg, 5.1 ft•lb)
M6 2 7 Nm (0.7 m•kg, 5.1 ft•lb)
2-15
TIGHTENING TORQUES
Tightening torque Remarks
LT
LT
LT
LT
LT
LT
LT