Download  Print this page

Yamaha ROADLINER XV19SW Owner's Manual

Hide thumbs




Table of Contents

  Also See for Yamaha ROADLINER XV19SW

  Summary of Contents for Yamaha ROADLINER XV19SW

  • Page 1 OWNER’S MANUAL XV19SW(C) XV19W(C) XV19MW(C) LIT-11626-20-40 1D7-28199-11...
  • Page 2 EAU10041...
  • Page 3 Yamaha has met these standards without reducing the performance or economy of operation of the motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual.
  • Page 4: Important Manual Information

    This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle is subsequently sold. Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your motorcycle and this manual.
  • Page 6 IMPORTANT MANUAL INFORMATION EAU10192 AFFIX DEALER LABEL HERE XV19SW(C)/XV19W(C)/XV19MW(C) OWNER’S MANUAL ©2006 by Yamaha Motor Corporation, U.S.A. 1st edition, June 2006 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited.
  • Page 7: Table Of Contents

    TABLE OF CONTENTS SAFETY INFORMATION ....1-1 PRE-OPERATION CHECKS ..... 4-1 Adjusting the rear brake light Location of important labels ...1-5 Pre-operation check list ....4-2 switch ........6-17 Checking the front and rear brake DESCRIPTION ........2-1 OPERATION AND IMPORTANT pads .......... 6-18 Left view ..........2-1 RIDING POINTS ........
  • Page 8 Matte color caution ......7-1 Care ..........7-1 Storage ...........7-3 SPECIFICATIONS ......8-1 CONSUMER INFORMATION.....9-1 Identification numbers ....9-1 Reporting safety defects ....9-3 Motorcycle noise regulation ....9-4 Maintenance record ......9-5 YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY ........9-7 YAMAHA EXTENDED SERVICE (Y.E.S.) ........9-9...
  • Page 9: Safety Information

    SAFETY INFORMATION EAU10281 AND/OR WHEN MADE NECES- • Ride where other motorists can SARY BY MECHANICAL CONDI- see you. Avoid riding in another MOTORCYCLES SINGLE TIONS. motorist’s blind spot. TRACK VEHICLES. THEIR SAFE USE Many accidents involve inexperi- AND OPERATION ARE DEPENDENT Safe riding enced operators.
  • Page 10 Modifications made to this motorcycle other motorists can see you. the single most critical factor in the pre- not approved by Yamaha, or the re- The posture of the operator and vention or reduction of head injuries. moval of original equipment, may ren- passenger is important for proper Always wear an approved helmet.
  • Page 11 Maximum load: been specifically designed for use on create instability due to improper 210 kg (463 lb) this motorcycle. Since Yamaha cannot weight distribution or aerody- test all other accessories that may be namic changes. If accessories When loading within this weight limit,...
  • Page 12 SAFETY INFORMATION tor and may limit control ability, Always turn the engine off before or clothing, immediately wash the therefore, such accessories are leaving the motorcycle unattended affected area with soap and water not recommended. and remove the key from the main and change your clothes.
  • Page 13: Location Of Important Labels

    SAFETY INFORMATION EAU10381 Location of important labels Please read the following important labels carefully before operating this vehicle.
  • Page 14 SAFETY INFORMATION California only PREMIUM UNLEADED GASOLINE ONLY 91 Min. Pump Octane (R+M) 2 5PW-2415E-11...
  • Page 15: Description

    DESCRIPTION EAU10410 Left view 1. Headlight (page 6-28) 9. Engine oil drain bolt B (crankcase) (page 6-9) 2. Clutch fluid reservoir (page 6-18) 10.Engine oil drain bolt A (crankcase) (page 6-9) 3. Seat lock (page 3-12) 11.Shift pedal (page 3-9) 4.
  • Page 16: Right View

    DESCRIPTION EAU10420 Right view 1. Helmet holder (page 3-13) 9. Engine oil filter cartridge (page 6-9) 2. Fuel injection system fuse (page 6-26) 10.Engine oil drain bolt (oil tank) (page 6-9) 3. Rear brake fluid reservoir (page 6-18) 11.Shock absorber assembly spring preload adjusting nut (page 3-14) 4.
  • Page 17: Controls And Instruments

    DESCRIPTION EAU10430 Controls and instruments 1. Clutch lever (page 3-9) 2. Left handlebar switches (page 3-7) 3. Multi-function meter unit (page 3-3) 4. Main switch/steering lock (page 3-1) 5. Right handlebar switches (page 3-7) 6. Throttle grip (page 6-13) 7. Brake lever (page 3-9)
  • Page 18: Instrument And Control Functions

    INSTRUMENT AND CONTROL FUNCTIONS EAU38390 EAU10540 To lock the steering Main switch/steering lock All electrical circuits are supplied with The main switch/steering lock is locat- power, and the meter lighting, taillight, ed under the main switch/steering lock license plate light and position lights cover.
  • Page 19: Indicator And Warning Lights

    6. Fuel level warning light “ ” for a few seconds, and then go off, Never turn the key to “OFF” or have a Yamaha dealer check the elec- EAU11030 “LOCK” while the vehicle is moving, trical circuit. Turn signal indicator lights “...
  • Page 20: Multi-Function Meter Unit

    When this occurs, a clock a self-diagnosis device have a Yamaha dealer check the self- a brightness control mode diagnosis system. (See page 3-3 for an explanation of the self-diagnosis de- 1. Speedometer NOTE: vice.)
  • Page 21 INSTRUMENT AND CONTROL FUNCTIONS Speedometer Tachometer 1. “SELECT” switch 1. Speedometer 1. Tachometer 2. Tachometer red zone The speedometer shows the riding The electric tachometer allows the rider speed. to monitor the engine speed and keep it When the key is turned to “ON”, the within the ideal power range.
  • Page 22 INSTRUMENT AND CONTROL FUNCTIONS Fuel gauge The fuel gauge does not indicate start counting the distance traveled the correct fuel level for the first 5 from that point. In that case, push the km/h (3 mi/h) after refueling. “SELECT” switch to switch the display between the various tripmeter, odome- ter, and clock modes in the following or- Odometer, tripmeter, and...
  • Page 23: To Set Clock

    1. Push the “SELECT” switch to indicates any error codes, note the (item number “1”) change the display to the clock code number, and then have a Yamaha the LCD (item number “2”) mode. dealer check the vehicle. the speedometer, tachometer, and 2.
  • Page 24: Handlebar Switches

    INSTRUMENT AND CONTROL FUNCTIONS 4. Adjust the multi-function meter unit EAU12347 Handlebar switches panel brightness level by pushing the “RESET” switch. Left 5. Push the “SELECT” switch to se- lect the LCD. Item number “2” is displayed. Adjust the LCD brightness level by pushing the “RESET”...
  • Page 25 This model can be equipped with op- has traveled both about 150 m (490 ft) tional lights available at a Yamaha and for approximately 15 seconds. dealer. However, the turn signal lights can also...
  • Page 26: Clutch Lever

    INSTRUMENT AND CONTROL FUNCTIONS EAU12820 EAU12880 EAU12890 Clutch lever Shift pedal Brake lever 1. Clutch lever 1. Shift pedal 1. Brake lever The clutch lever is located at the left The shift pedal is located on the left The brake lever is located at the right handlebar grip.
  • Page 27: Brake Pedal

    INSTRUMENT AND CONTROL FUNCTIONS EAU12941 EAU13120 2. Turn the key counterclockwise to Brake pedal Fuel tank cap the original position, remove it, and then close the lock cover. NOTE: The fuel tank cap cannot be installed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and locked.
  • Page 28: Fuel

    1. Fuel tank filler tube ONLY 2. Fuel level mended by Yamaha because it can Fuel tank capacity: cause damage to the fuel system or ve- 17.0 L (4.49 US gal) (3.74 Make sure that there is sufficient fuel in hicle performance problems.
  • Page 29: Catalytic Converter

    INSTRUMENT AND CONTROL FUNCTIONS EAU13431 EAU34042 Catalytic converter Rider seat This model is equipped with a catalytic converter in the exhaust system. To remove the rider seat 1. Insert the key into the seat lock, EWA10860 WARNING and then turn it counterclockwise. The exhaust system is hot after op- eration.
  • Page 30: Helmet Holder

    INSTRUMENT AND CONTROL FUNCTIONS EAU38341 To release the helmet from the hel- Helmet holder met holder Remove the rider seat, remove the hel- met holding cable from the helmet hold- er and the helmet, and then install the seat. 1. Helmet holding cable 2.
  • Page 31: Adjusting The Shock Absorber Assembly

    INSTRUMENT AND CONTROL FUNCTIONS EAU38401 load and thereby soften the sus- With each complete turn of the ad- Adjusting the shock absorber pension, turn the adjusting nut in justing nut, distance A is changed assembly direction (b). by 2.0 mm (0.08 in). This shock absorber assembly is equipped with a spring preload adjust- ing nut.
  • Page 32: Exup System

    Always have a Yamaha dealer EAU15281 EXUP system CAUTION: service the shock absorber. This model is equipped with Yamaha’s Always tighten the locknut against EXUP (EXhaust Ultimate Power valve) the adjusting nut, and then tighten system. This system boosts engine the locknut to the specified torque.
  • Page 33: Sidestand

    INSTRUMENT AND CONTROL FUNCTIONS EAU15301 below and have a Yamaha dealer re- EAU15311 Sidestand Ignition circuit cut-off system pair it if it does not function proper- The sidestand is located on the left side The ignition circuit cut-off system (com- of the frame.
  • Page 34 5. Push the start switch. Does the engine start? The neutral switch may be defective. The motorcycle should not be ridden until checked by a Yamaha dealer. With the engine still running: 6. Move the sidestand up. 7. Keep the clutch lever pulled.
  • Page 35: Auxiliary Dc Connector

    INSTRUMENT AND CONTROL FUNCTIONS EAU38350 EWA12531 Auxiliary DC connector WARNING To prevent electrical shock or short- circuiting, make sure that the cap is installed when the auxiliary DC con- nector is not being used. 1. Auxiliary DC connector A 12-V accessory connected to the auxiliary DC connector under the rider seat can be used when the key is in the “ON”...
  • Page 36: Pre-Operation Checks

    PRE-OPERATION CHECKS EAU15591 The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air pressure could have serious consequences.
  • Page 37: Pre-Operation Check List

    • If necessary, add recommended fluid to specified level. • Check hydraulic system for leakage. • Make sure that operation is smooth. • Check cable free play. Throttle grip 6-13, 6-21 • If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing.
  • Page 38 Chassis fasteners — • Tighten if necessary. Instruments, lights, signals • Check operation. — and switches • Correct if necessary. • Check operation of ignition circuit cut-off system. Sidestand switch 3-16 • If system is defective, have Yamaha dealer check vehicle.
  • Page 39: Operation And Important Riding Points

    EWA10290 Yamaha dealer check the electrical cir- WARNING Never start the engine or oper- cuit. ate it in a closed area for any Before...
  • Page 40: Shifting

    OPERATION AND IMPORTANT RIDING POINTS ECA11130 EAU16671 ECA10260 Shifting CAUTION: CAUTION: For maximum engine life, always Even with the transmission in warm the engine up before starting the neutral position, do not off. Never accelerate hard when the coast for long periods of time engine is cold! with the engine off, and do not tow the motorcycle for long dis-...
  • Page 41: Engine Break-In

    OPERATION AND IMPORTANT RIDING POINTS 4. At the recommended shift points 3. Shift the transmission into the neu- EAU16841 Engine break-in shown in the following table, close tral position when the motorcycle There is never a more important period the throttle, and at the same time, is almost completely stopped.
  • Page 42: Parking

    If any engine trouble should oc- may overturn. cur during the engine break-in ECA10380 period, immediately have a CAUTION: Yamaha dealer check the vehi- Never park in an area where there cle. are fire hazards such as grass or other flammable materials.
  • Page 43: Periodic Maintenance And Minor Repair

    TRAINED AND EQUIPPED TO PER- certain maintenance work correctly. FORM THESE PARTICULAR SER- VICES. NOTE: If you do not have the tools or experi- ence required for a particular job, have a Yamaha dealer perform it for you.
  • Page 44 PERIODIC MAINTENANCE AND MINOR REPAIR EWA10340 WARNING Modifications approved Yamaha may cause loss of perfor- mance, excessive emissions, and render the vehicle unsafe for use. Consult a Yamaha dealer before at- tempting any changes.
  • Page 45: Periodic Maintenance Chart For The Emission Control System

    • Replace gasket(s) if necessary. Evaporative emis- • Check control system for dam- √ √ sion control system age. (For California only) • Replace if necessary. * Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
  • Page 46: General Maintenance And Lubrication Chart

    PERIODIC MAINTENANCE AND MINOR REPAIR EAU32183 General maintenance and lubrication chart INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months...
  • Page 47 PERIODIC MAINTENANCE AND MINOR REPAIR INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months 18 months 24 months 30 months...
  • Page 48 • Lubricate the throttle grip housing and cable. Lights, signals and • Check operation. √ √ √ √ √ √ 26 * switches • Adjust headlight beam. * Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
  • Page 49 PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months. EAU38440 NOTE: Air filter • This model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with com- pressed air to avoid damaging it.
  • Page 50: Checking The Spark Plugs

    Do not attempt to diagnose 0.8–0.9 mm (0.031–0.035 in) such problems yourself. Instead, have a Yamaha dealer check the vehicle. Clean the surface of the spark plug If a spark plug shows signs of electrode gasket and its mating surface, and then...
  • Page 51: Canister (For California Only)

    PERIODIC MAINTENANCE AND MINOR REPAIR EAU19681 EAU38361 Canister (for California only) Engine oil and oil filter car- NOTE: To achieve the proper engine oil tem- tridge perature for an accurate oil level read- The engine oil level should be checked ing, the engine must have first before each ride.
  • Page 52 PERIODIC MAINTENANCE AND MINOR REPAIR ECA10900 CAUTION: Make sure that the oil filler cap is se- curely tightened, otherwise oil may seep out when the engine is run- ning. To change the engine oil (with or without oil filter cartridge replace- 1.
  • Page 53 NOTE: An oil filter wrench is available at a Tightening torques: Yamaha dealer. Engine oil drain bolt A (crankcase): 43 Nm (4.3 m·kgf, 31 ft·lbf) 8. Apply a thin coat of engine oil to Engine oil drain bolt B (crankcase): the O-ring of the new oil filter car- 43 Nm (4.3 m·kgf, 31 ft·lbf)
  • Page 54: Transfer Case Oil

    13. Remove the engine oil filler cap, 15. Start the engine, and then let it idle changed by a Yamaha dealer at the in- and then gradually fill the oil tank for several minutes while checking...
  • Page 55: Air Filter Element

    To prevent this Have a Yamaha dealer replace the air from occurring, the valve clearance filter element. must be adjusted by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart.
  • Page 56: Tires

    PERIODIC MAINTENANCE AND MINOR REPAIR EAU21750 evenly from side to side. Properly Tire air pressure (measured on cold Tires adjust the suspension for your load, tires): To maximize the performance, durabil- and check the condition and pres- 0–90 kg (0–198 lb): ity, and safe operation of your motor- Front: sure of your tires.
  • Page 57 Use only the tire valves and in it, or if the sidewall is cracked, con- valve cores listed below to tact a Yamaha dealer immediately and avoid tire deflation during a have the tire replaced. high-speed ride.
  • Page 58: Cast Wheels

    Other tires may run fore each ride. If any damage is parts you choose for your vehicle the danger of bursting at super found, have a Yamaha dealer re- should be designed specifically for high speeds. place the wheel. Do not attempt...
  • Page 59: Clutch Lever

    If there is air in the hydraulic 1. Rear brake light switch system, have a Yamaha dealer bleed 2. Rear brake light switch adjusting nut the system before operating the motor- The rear brake light switch, which is ac- cycle.
  • Page 60: Checking The Front And Rear Brake Pads

    EAU38630 Checking the front and rear Checking the brake and clutch peared, have a Yamaha dealer replace brake pads fluid levels the brake pads as a set. The front and rear brake pads must be...
  • Page 61 However, if the the top of each reservoir is level. brake fluid level goes down sud- Use only the recommended quality denly, have a Yamaha dealer brake fluid, otherwise the rubber check the cause. seals may deteriorate, causing leakage and poor braking or clutch performance.
  • Page 62: Changing The Brake And Clutch Fluids

    The drive belt slack should be checked applied to the belt with a belt ten- and adjusted at the intervals specified Have a Yamaha dealer change the sion gauge as shown. in the periodic maintenance and lubri- brake and clutch fluids at the intervals NOTE: cation chart.
  • Page 63: Checking And Lubricating The Cables

    If a cable is damaged maintenance chart. or does not move smoothly, have a Yamaha dealer check or replace it. Recommended lubricant: Yamaha Chain and Cable Lube or engine oil SAE 10W-30...
  • Page 64: Checking And Lubricating The Brake And Clutch Levers

    PERIODIC MAINTENANCE AND MINOR REPAIR EAU23140 Recommended lubricant: Recommended lubricant: Checking and lubricating the Lithium-soap-based grease (all-pur- Lithium-soap-based grease (all-pur- brake and clutch levers pose grease) pose grease) Brake lever Clutch lever The operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lu- bricated if necessary.
  • Page 65: Checking And Lubricating The Sidestand

    2. While applying the front brake, If the sidestand does not move up push down hard on the handlebars and down smoothly, have a Yamaha several times to check if the front dealer check or repair it. fork compresses and rebounds smoothly.
  • Page 66: Checking The Steering

    Securely support the vehicle so that fork does not operate smoothly, there is no danger of it falling over. have a Yamaha dealer check or re- pair it. 2. Hold the lower ends of the front fork legs and try to move them for- ward and backward.
  • Page 67: Checking The Wheel Bearings

    To charge the battery furic acid, which causes severe Have a Yamaha dealer charge the bat- burns. Avoid any contact with tery as soon as possible if it seems to skin, eyes or clothing and al- have discharged.
  • Page 68: Replacing The Fuses

    (MF) battery charg- The main fuse, the fuel injection system electrical accessories. er, have a Yamaha dealer fuse, and the fuse box, which contains charge your battery. the fuses for the individual circuits, are To store the battery located under the rider seat.
  • Page 69 PERIODIC MAINTENANCE AND MINOR REPAIR 4. If the fuse immediately blows Specified fuses: again, have a Yamaha dealer Main fuse: check the electrical system. 50.0 A Headlight fuse: 20.0 A Signaling system fuse: 10.0 A Ignition fuse: 25.0 A Fuel injection system fuse: 15.0 A...
  • Page 70: Replacing A Headlight Bulb

    PERIODIC MAINTENANCE AND MINOR REPAIR EAU38451 Replacing a headlight bulb 1. Bolt 1. Screw 2. Main switch/steering lock cover 1. Low beam headlight bulb To replace the high beam headlight 2. Disconnect the coupler shown. 2. High beam headlight bulb bulb 1.
  • Page 71 PERIODIC MAINTENANCE AND MINOR REPAIR 2. Disconnect the headlight coupler, ECA10650 CAUTION: and then unhook the headlight bulb holder. Take care not to damage the follow- ing parts: Headlight bulb Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transpar- ency of the glass, the luminosity of the bulb, and the bulb life will...
  • Page 72 3. Install the main switch/steering gerprints on the headlight bulb lock cover by installing the bolts. using a cloth moistened with al- 4. Have a Yamaha dealer adjust the 1. Headlight coupler cohol or thinner. headlight beam if necessary. 2. Headlight bulb...
  • Page 73: Tail/Brake Light

    If the license plate light does not come type of tail/brake light. on, have a Yamaha dealer check the 1. Remove the turn signal light lens If the tail/brake light does not come on, electrical circuit or replace the bulb.
  • Page 74: Supporting The Motorcycle

    However, should your motorcycle To service the front wheel require any repair, take it to a Yamaha 1. Stabilize the rear of the motorcycle dealer, whose skilled technicians have by using a motorcycle stand or, if...
  • Page 75: Troubleshooting Chart

    Remove the spark plugs and check the electrodes. The engine does not start. Have a Yamaha dealer check the vehicle. Check the battery. 4. Battery The engine turns over The battery is good.
  • Page 76: Motorcycle Care And Storage

    Rust and corrosion can develop matte colored finished parts. Be Cleaning even if high-quality components are sure to consult a Yamaha dealer for ECA10770 advice on what products to use be- used. A rusty exhaust pipe may go un- CAUTION: fore cleaning the vehicle.
  • Page 77 MOTORCYCLE CARE AND STORAGE cleaning products, solvent or After normal use ECA10790 CAUTION: thinner, fuel (gasoline), rust re- Remove dirt with warm water, a mild movers or inhibitors, brake flu- detergent, and a soft, clean sponge, Do not use warm water since it in- id, antifreeze or electrolyte.
  • Page 78: Storage

    WARNING NOTE: ing it with a tarp, while it is still Consult a Yamaha dealer for advice on Make sure that there is no oil or wet, will allow water and humid- what products to use.
  • Page 79 MOTORCYCLE CARE AND STORAGE 3. Perform the following steps to pro- 4. Lubricate all control cables and the tect the cylinders, piston rings, etc. pivoting points of all levers and from corrosion. pedals as well as of the side- a. Remove the spark plug caps stand/centerstand.
  • Page 80: Specifications

    SPECIFICATIONS Dimensions: Engine oil: Manufacturer/model: DENSO/X24EPR-U9 Overall length: Type: Spark plug gap: 2580 mm (101.6 in) YAMALUBE 4 (20W40) or SAE20W40 0.8–0.9 mm (0.031–0.035 in) Overall width: Recommended engine oil grade: Clutch: 1100 mm (43.3 in) API service SG type or higher, JASO Overall height: standard MA Clutch type:...
  • Page 81 SPECIFICATIONS Caster angle: Rear: Operation: 31.30 ° 280 kPa (41 psi) (2.80 kgf/cm²) Right foot operation Trail: Loading condition: Recommended fluid: 152.0 mm (5.98 in) 90–210 kg (198–463 lb) DOT 4 Front tire: Front: Front suspension: 250 kPa (36 psi) (2.50 kgf/cm²) Type: Type: Rear:...
  • Page 82 SPECIFICATIONS High beam headlight: ECU fuse: 12 V, 55.0 W × 1 10.0 A Tail/brake light: Fuel injection system fuse: 15.0 A Front turn signal/position light: Auxiliary DC connector fuse: 12 V, 23 W/8.0 W × 2 3.0 A Rear turn signal light: Backup fuse: 12 V, 21.0 W ×...
  • Page 83: Consumer Information

    Record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehi- cle is stolen. KEY IDENTIFICATION NUMBER: 1.
  • Page 84 1. Model label The model label is affixed to the frame under the rider seat. (See page 3-12.) Record the information on this label in the space provided. This information will be needed when ordering spare parts from a Yamaha dealer.
  • Page 85: Reporting Safety Defects

    If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
  • Page 86: Motorcycle Noise Regulation

    CONSUMER INFORMATION EAU26560 Motorcycle noise regulation TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED: Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve- hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
  • Page 87: Maintenance Record

    CONSUMER INFORMATION EAU26632 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required.
  • Page 88 CONSUMER INFORMATION Maintenance Date of Servicing dealer Mileage Remarks interval service name and address 36000 mi (55000 km) or 54 months 40000 mi (61000 km) or 60 months...
  • Page 89: Yamaha Motor Corporation, U.s.a. Street And Enduro Motorcycle Limited Warranty

    CONSUMER INFORMATION EAU26663 YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY Yamaha Motor Corporation, U.S.A. hereby warrants that CUSTOMER’S RESPONSIBILITY under this Engine new Yamaha motorcycles will be free from defects in warranty shall be to: Displacement Period...
  • Page 90 CUSTOMER SERVICE What costs are my responsibility during the warranty period? If your machine requires warranty service, you must take it to any authorized Yamaha The customer’s responsibility includes all costs of normal maintenance services, motorcycle dealer within the continental United States. Be sure to bring your warranty non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, registration card or other valid proof of the original date of purchase.
  • Page 91: Yamaha Extended Service (Y.e.s.)

    This excellent Y.E.S. plan coverage is only available to dealer to see how comforting uninterrupted factory- Yamaha owners like you, and only while your Yamaha is still backed protection can be. within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts.
  • Page 92 Yamaha Limited Warranty expires. A special note: If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need.
  • Page 93 INDEX Fuel ............3-11 Pre-operation check list ......4-2 Fuel level warning light......3-2 Accessories and replacement parts ..6-16 Fuel tank cap.........3-10 Air filter element........6-13 Rear brake light switch, adjusting ..6-17 Fuses, replacing........6-26 Auxiliary DC connector ......3-18 Rear suspension, lubricating ....6-23 Rider seat ..........
  • Page 94 INDEX Valve clearance ........6-13 Vehicle identification number ....9-1 Warranty, extended......... 9-9 Warranty, limited ........9-7 Wheel bearings, checking..... 6-25 Wheels ..........6-16...