Epson PP-100II Technical Reference Manual page 77

Section name Key name
[JOB_ID] DETAIL_STATUS
ESTIMATION_TIME_RE
MAIN
PUBLISHER[N] NAME
This is an
information of each
STACKER1
PUBLISHER.
* [N] stands for a
machine number
that starts from 1.
STACKER2
STACKER3
STACKER4
INK_C
INK_M
INK_Y
INK_LC
INK_LM
INK_B
INFO[M]
* [M] stands for a
number that starts
from 1.
Chapter 4 Development Guide for a Cooperative Application
Explanation
An ID showing the detailed status of the
job is output.
For changes of the status of the
DETAIL_STATUS key, see "Values Output
to DETAIL_STATUS Key and Transition
Diagram" on page 4-81.
An estimated time for remaining
processing the job.
(Jobs with the error rate measurement
setting only are not written.)
The publishing machine names
registered by EPSON Total Disc Setup are
written.
The remaining amount of discs in the
stacker 1 of the specified publisher is
expressed in percentage. Note that this is
not the number of remaining discs.
The remaining amount of discs in the
stacker 2 of the specified publisher is
expressed in percentage. Note that this is
not the number of remaining discs.
The status of the stacker 3 (full or not full)
of the specified publisher is written.
The status of the stacker 4 (full or not full)
of the specified publisher is written.
The cyan ink level of the specified
publisher is written.
The magenta ink level of the specified
publisher is written.
The yellow ink level of the specified
publisher is written.
The light cyan ink level of the specified
publisher is written.
The light magenta ink level of the
specified publisher is written.
The black ink level of the specified
publisher is written.
The hardware status is written by
INFORMATION code.
If multiple INFORMATION codes exist, the
corresponding multiple codes are
written.
When the hardware recovers from the
status, the INFORMATION code is deleted
when the STF file is updated.
The "INFOR[M]=" always appear even
while the hardware is operating normally.
Output values that indicate
status
Reception processing: "1"
Waiting for publishing: "2"
Publishing: "3"
Pause processing: "4"
Waiting for return processing: "5"
Canceling processing: "6"
Paused: "7"
Waiting for return: "8"
Done (no alarm, no error disk): "9"
5
Done (alarm, no error disk): "10" *
5
Done (alarm, error disk): "11" *
User cancel done: "12"
Error cancel done: "13"
Reception refused: "14"
Unknown: "99"
An estimated time until the remaining
job is completed in increments of one
second.
* This key is not written for completed
jobs.
Publishing machine name
The percentage ("0" to "100")
Unknown: "-1"
The percentage ("0" to "100")
Unknown: "-1"
When the stacker is full: "100"
When the stacker is not full: "0"
Unknown: "-1"
When the stacker is full: "100"
When the stacker is not full: "0"
Unknown: "-1"
(*2)
The percentage ("0" to "100")
Unknown: "-1"
(*2)
The percentage ("0" to "100")
Unknown: "-1"
(*2)
The percentage ("0" to "100")
Unknown: "-1"
(*2)
The percentage ("0" to "100")
Unknown: "-1"
(*2)
The percentage ("0" to "100")
Unknown: "-1"
(*2)
The percentage ("0" to "100")
Unknown: "-1"
See "INFORMATION Code List".
Change
timing
When the job status
changes
As needed while
the job is being
published
Always appears as
long as registered
machine exists
Each time the
remaining amount
of discs changes
Each time the
remaining amount
of discs changes
When the stacker
full status or not-full
status is detected.
4
When the stacker
full status or not-full
status is detected.
Each time the ink is
consumed
Each time the ink is
consumed
Each time the ink is
consumed
Each time the ink is
consumed
Each time the ink is
consumed
Each time the ink is
consumed
Each time an error
occurs
77