Changing The Equalizer Settings; Connecting To Audio Equipment - Roland FP-2 Owner's Manual

Chapter 4 Other Functions
Changing the Equalizer
Settings
You can make fine, detailed changes to the equalizer settings.
1.
Switch to Function mode (p. 38), and press the
[Equalizer] button.
2.
Hold down the [Equalizer] button, and press the
[-] or [+] button to select item.
3.
Press the [-] or [+] button to change the settings.
Param Indi-
Value
eter cation
Low Lo.G -12–+12dB
Gain
Low Lo.f 100, 200, 400
(Hz)
Freq
-12–+12dB
Low Lm.G
Mid
Gain
Low Lm.F 200, 250, 315,
400, 500, 630,
Mid
800, 1.00, 1.25,
Freq
1.60, 2.00, 2.50,
3.15, 4.00, 5.00,
6.30, 8.00
Low Lm.q 0.5, 1.0, 2.0,
4.0, 8.0
Mid
Q
High Hm.G -12–+12dB
Mid
Gain
High Hm.F 200, 250, 315,
400, 500, 630,
Mid
800, 1.00, 1.25,
Freq
1.60, 2.00, 2.50,
3.15, 4.00, 5.00,
6.30, 8.00
0.5, 1.0, 2.0,
High Hm.q
4.0, 8.0
Mid
Q
44
Description
Adjusts the level of the low-
frequency range.
Frequency point in the low-
frequency range. Generally,
this changes the level at and
below this frequency.
Adjusts the level of the low-
frequency range to
midrange.
Frequency point in the low-
frequency range to
midrange. This changes the
level of the specified band-
width centered on this fre-
quency.
Changes the bandwidth of
the low-frequency range to
midrange. The bandwidth
affected by the controls nar-
rows as the value increases.
Adjusts the level of the mid-
to high-frequency range.
Frequency point in the mid-
to high-frequency range to
midrange. This changes the
level of the specified band-
width centered on this fre-
quency.
Changes the bandwidth of
the mid- to high-frequency
range. The bandwidth
affected by the controls nar-
rows as the value increases.
Param Indi-
Value
eter cation
High Hi.G -12–+12dB
Gain
High 2.00, 4.00, 8.00
Hi.F
(KHz)
Freq
* Sounds may become distorted as the Gain level increases.
→ The equalizer is switched on whenever the settings are
changed.
→ The FP-2 remembers the settings even while its power is
turned off.
Connecting to Audio
Equipment
You can connect audio devices to play the sound of the FP-2
through the speakers of your audio system, or to record your
performance on a tape recorder or other recording device.
When connecting, please use an audio cable with a standard
phone plug (sold separately).
Connection Examples
* To prevent malfunction and/or damage to speakers or other
devices, always turn down the volume, and turn off the power
on all devices before making any connections.
Playing the sound of the FP-2 through the speakers
of an audio system/Recording the performance of
the FP-2 on a recording device
fig.audio1.e
FP-2
❍ Use the following procedure when turning on the power.
1.
Set the volume of the FP-2 and of the connected
devices to the minimum position.
2.
Set the speaker switch to "Off" located on the rear
panel.
3.
Turn on the power of the FP-2.
4.
Turn on the power of the connected device.
5.
Adjust the volume of each device.
Description
Adjusts the level of the high-
frequency range.
Frequency point in the high-
frequency range. Generally,
this changes the level at and
over this frequency.
Input R/L
(Line In, Aux In)