Installation - Salicru SPS 750 ADV R User Manual

5. INSTALLATION.

Read and respect the Safety Information, described
•
in chapter 2 of this document. failure to obey some
of the instructions described in this manual can result in a
serious or very serious accident to persons in direct contact
or in the vicinity, as well as faults in the equipment and/or
loads connected to it.
5.1. reCepTion of The deviCe.
Pay attention to section 1.2.1. of the safety instructions
•
-ek266*08- in all matters relating to the handling, move-
ment and siting of the unit.
Use the most appropriate means to move the UPS.
•
Any handling of the device must be carried out in accordance
•
with the weights shown in the technical specifications ac-
cording to the model, indicated in chapter "9. Annexes".
5.1.1. reception, unpacking and contents.
Reception. Check that:
•
The data on the label affixed to the packaging corres-
ˆ
ponds to that specified on the order. once the UPS is
unpacked, check the previous data with those of the
equipment nameplate.
If there are discrepancies, file the disagreement as
soon as possible, citing the equipment manufacture
number and the delivery note references.
There is no damage to the packaging that may have
ˆ
occurred during transportation.
If there is damage, notify the carrier and indicate so on
the delivery note, and, as soon as possible, inform the
supplier / distributor or, failing that, our firm.
Unpacking.
•
Remove the packaging to check the contents.
ˆ
Cut the seal and open the cardboard box.
–
Remove:
–
The bag containing cable or cables.
The bag containing AdvAnCe R mechanical ele-
ments (angles, screws, etc.).
The input power cable.
Remove the device and plastic bag from the pa-
–
ckaging and detach the protective corners.
Inspect the device before proceeding and, in the
–
event of finding damage, contact the supplier / dis-
tributor or, failing that, our firm.
do not leave any plastic bags within the reach
of children to avoid the danger of suffocation.
disposal of the packaging must be carried out in ac-
ˆ
cordance with current laws.
we recommend keeping it for at least one year.
Contents.
•
device:
ˆ
1 UPS.
–
Quick guide on paper.
–
Information for warranty registration.
–
1 RS232 cable.
–
1 USb cable (only in SPS AdvAnCe T models).
–
1 cable for the device's AC power supply.
–
USER MANUAL
2 metal pieces for use as handles and screws for
–
installing the unit in a rack cabinet (only in SPS
AdvAnCe R models).
optional battery module (only in AdvAnCe T models):
ˆ
1 battery module:
–
Information for warranty registration.
–
1 cable for interconnecting the battery module and
–
UPS or other module.
once the reception is completed, it is advisable to re-pack
•
the UPS until it is put into service in order to protect it
against mechanical shock, dust, dirt, etc.
5.1.2. storage.
equipment storage shall be done in a dry, ventilated place
•
and protected from rain, dust, water splashes or chemical
agents. It is advisable to keep each device and battery unit
in its original packaging, as it has been specifically de-
signed to ensure maximum protection during transportation
and storage.
for devices that contain Pb-Ca batteries, the
•
charging times indicated in Tab. 2 of document
ek266*08, determined by the temperature to which they
are exposed, must be respected, otherwise the warranty
may be invalidated.
After this period, connect the device to the mains together
•
with the battery unit if applicable according to the instruc-
tions described in this manual and charge for 12 hours.
Then disconnect and store the UPS and batteries in their
•
original packaging, noting the new date for recharging the
batteries on a document as a record or even on the pack-
aging itself.
do not store the devices where the ambient temperature
•
exceeds 50ºC or drops below -20ºC, as this may cause deg-
radation of the electrical characteristics of the batteries.
5.1.3. Transport to the site.
It is advisable to move the UPS using the most suitable
•
means for this. If the distance is considerable, it is recom-
mended to transport the device in its packaging to the in-
stallation site and then unpack it.
5.1.4. siting, immobilising and considerations.
The AdvAnCe R models are designed for mounting as a
•
rack (installation in 19" cabinets and in horizontal position
(see section 5.1.4.1) and the AdvAnCe T models as a tower
(in vertical position), just like their optional battery modules.
for all instructions regarding connections, refer to section
•
5.2.
SPS ADVANCE R & T UnInTeRRUPTIbLe PoweR SUPPLy (UPS)
13