Advertisement
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your VM-3DT. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to the VM-3DT.
RJ-45 Pinout:
For HDBaseT connectors:
PIN EIA /TIA 568B
PIN
1
2
3
4
5
6
7
Step 5: Connect the power
Connect the power adapter to the VM-3DT and plug the adapter into the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power supply that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See
www.KramerAV.com
for updated safety information.
Step 6: Acquire the EDID
To acquire an EDID, press the EDID SETUP button as follows:
1. Press the EDID SETUP button once.
The OUTPUTS CONNECTED LEDs flash to indicate the current EDID used: 1, 2, or 3, or all if the default EDID is currently used.
2. Press the EDID SETUP button again to enter the EDID read mode and then press repeatedely to cycle through the EDID source
options until the desired EDID source is reached: OUT 1 -> OUT 2 -> OUT 3 -> all LEDs flash (for a default EDID).
3. Wait a few seconds for the VM-3DT to read the EDID. When complete, all LEDs display the present output connection status.
Technical Specifications
Input:
1 HDBT on an RJ-45 female connector
Outputs:
3 HDBT on RJ-45 female connectors
Extension
HDBaseT 1.0 compliant.
Line / Range:
Up to 40m (130ft) at 4K@60Hz (4:2:0); Up to 70m (230ft) at full HD (1080p@60Hz 36bpp).
Note: When using Kramer HDBaseT cables. This reach applies to each IN and OUT port separately, the total
end-to-end reach is the sum of all ports' reach.
Video:
Up to 4K@60Hz (4:2:0) resolution; Up to 10.2Gbps (3.4Gbps per graphic channel) data rate; Complies with
HDMI 2.0 and HDCP 1.4
Controls:
EDID SETUP button; Indicator LEDs: OUTPUTS CONNECTED 1-3, HDBT LINK 1-3, ACTIVE INPUT, ON
Operating
Operating Temperature: 0° to +40°C (32° to 104°F); Storage Temperature: -40° to +70°C (-40° to 158°F);
Conditions:
Humidity: 10% to 90%, RHL non-condensing
Power:
Power Source: 5.2V/4A; Power Consumption: 5V DC, 3.2A
Dimensions:
21.5cm x 16.3cm x 4.4cm (8.4" x 6.4" x 1.8"); Shipping: 35.1cm x 21.2cm x 7.2cm (13.8" x 8.3" x 2.8") (W, D, H)
Weight:
0.53kg (1.17lb); Shipping Weight: 1.29kg (2.84lb)
Included Accessories:
Power supply
Specifications are subject to change without notice at
DIP-Switch Setup:
Wire Color
Orange / White
Orange
Green / White
Blue
Blue / White
Out #
Green
OUT 1
Brown / White
OUT 2
OUT 3
www.kramerav.com
IR Routing is enabled when:
DIP 1 – OFF (up)
DIP 2 – OFF (up)
DIP 3 – OFF (up)
Note: DIP-switches 4 and 8
are reserved for future use.
By default, all DIP-switches
are set to OFF (up).
RS-232 Routing is enabled when:
DIP 5 – OFF (up)
DIP 6 – OFF (up)
DIP 7 – OFF (up)
Advertisement
