Kramer Electronics Ltd. Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we...
European Advanced Recycling Network (EARN) and will cover any costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular country go to our recycling pages at www.kramerav.com/support/recycling.
• Long-distance AV signal extension for multi-room, large dividable auditoriums and lecture hall connectivity. • AV extension in conference rooms, boardrooms, control rooms, hotels and large church facilities. WP-789T, TP-789R, TP-789Rxr – Introduction...
HDBT OUT RJ-45 Connector 789R). Power Supply 2-pin Terminal Connect to a power supply (if required). Connect GND to GND, +12V Block Connector to +12V. WP-789T, TP-789R, TP-789Rxr – Defining WP-789T, TP-789R, TP-789Rxr HDMI Line Transmitters and Receivers over HDBaseT...
Page 7
48V DC Power Terminal Block TP-789R, TP-789Rxr provides PoE, connect it to the Kramer power supply. If it accepts PoE, no power connection is needed. WP-789T, TP-789R, TP-789Rxr – Defining WP-789T, TP-789R, TP-789Rxr HDMI Line Transmitters and Receivers over HDBaseT...
Attach the rubber feet and place the unit on a flat surface. • Fasten a bracket (included) on each side of the unit and attach it to a flat surface. For more information go to www.kramerav.com/downloads/TP-789Rxr WP-789T, TP-789R, TP-789Rxr – Mounting...
• UK: 1 Gang in-wall junction box, 75x75mm (W, H) and depth that can fit in both the device and the connected cables (BS 4662 or BS EN 60670-1 used with supplied spacers and screws). WP-789T, TP-789R, TP-789Rxr – Mounting...
For illustrative purposes, the figure below shows TP-789R, but the same connections apply to TP-789Rxr, with the addition of an Ethernet connector. Figure 4: Connecting WP-789T toTP-789R To connect WP-789T, TP-789R, TP-789Rxr as illustrated in the example in (Figure 1. Connect the HDMI IN Connector on the...
HDBaseT and the video acceptor via Ethernet control extension over HDBaseT. For illustrative purposes, the figure below shows TP-789Rxr, but the same connections apply TP-789R except for the Ethernet connection. Figure 5: Connecting TP-789Rxr WP-20 WP-789T, TP-789R, TP-789Rxr – Connecting WP-789T, TP-789R, TP-789Rxr...
Page 12
Ethernet RJ-45 Connector on the TP-789Rxr rear panel. 7. Connect the power adapter to the 48V DC Power Terminal Block TP-789R/TP-789Rxr rear panel and to the mains electricity (not shown in Figure WP-789T, TP-789R, TP-789Rxr – Connecting WP-789T, TP-789R, TP-789Rxr...
Connect the RS-232 D-sub Connector on the TP-780Txr rear panel to an RS-232 controller (for example, SL-240C). b. Connect the Ethernet RJ-45 Connector on the TP-780Txr rear panel to a LAN- enabled to controller (for example, SL-240C). WP-789T, TP-789R, TP-789Rxr – Connecting WP-789T, TP-789R, TP-789Rxr...
RS-232 communication to the other end of the HDBaseT extension to control an external device. • Firmware Upgrade – Contact your local technical support. To connect to WP-789T, TP-789R, TP-789Rxr via RS-232 from a D-sub connector: • Pin 2 to the Tx pin on the WP-789T, TP-789R, TP-789Rxr RS-232 terminal block.
Page 15
Blu-ray player source). To emit a wide-range modulated IR signal: • Connect the emitter wires to the WP-789T IR terminal block as illustrated in Figure Figure 8: Connecting IR Emitter – Wide-Range Modulated WP-789T, TP-789R, TP-789Rxr – Connecting WP-789T, TP-789R, TP-789Rxr...
Page 16
SL-240C). WP-789T then extends the signal to an acceptor (for example, a display) that is connected to the IR port of the HDBaseT receiver (for example, Kramer TP-789R) via IR emitter cable. To extend an IR signal from a controller: •...
Set to OFF for backward compatibility with 38kHz IR extension. FW Upgrade OFF – Normal operation mode. ON – FW upgrade mode (contact customer support). When set to ON device operation is disabled. WP-789T, TP-789R, TP-789Rxr – Configuring WP-789T, TP-789R, TP-789Rxr...
To set the TP-789Rxr HDBaseT range mode: • Set DIP-switch 1 according to the DIP-switch configuration table (see Configuration DIP- Switches on page 15). Upgrading Firmware Contact technical support to upgrade the WP-789T, TP-789R, TP-789Rxr device firmware WP-789T, TP-789R, TP-789Rxr – Configuring WP-789T, TP-789R, TP-789Rxr...
For the US version: 2 US-D frame sets and faceplates (in black and in white) For the European version: 1 EU white frame, 1 UK white frame, 1 EU/UK white faceplate Specifications are subject to change without notice at www.kramerav.com. WP-789T, TP-789R, TP-789Rxr – Technical Specifications...
(6.2" x 4.7" x 3.4") Net Weight, each 0.2kg (0.44bs) approx. Shipping Weight 0.72kg (1.6lbs) approx. Accessories Included 1 Power adapter, 1 power cord and 1bracket set per device Specifications are subject to change without notice at www.kramerav.com. WP-789T, TP-789R, TP-789Rxr – Technical Specifications...
Page 21
Electronics products, this product must be insured during shipment, with the insurance and shipping charges prepaid by you. If this product is returned uninsured, you assume all risks of loss or damage during shipment. Kramer Electronics will not be responsible for any costs related to the removal or re- installation of this product from or into any installation.
Page 22
SAFETY WARNING Disconnect the unit from the power supply before opening and servicing For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found. We welcome your questions, comments, and feedback.