Service; List Of Error Numbers - Siemens SITRANS F C MASSFLO MASS 6000 Ex-d Manual

SITRANS F C MASSFLO
6.

Service

6.1 List of error numbers

    
6. Service
Error Error text
No. Remedy text
1 I1 - Power on
OK
2 I2 - Add-on module
Applied
3 I3 - Add-on module
Install
4 I4 - Param. corrected
OK
20 W20 - Totalizer 1
Reset manually
20 W20 - Totalizer 2
Reset manually
21 W21 - Pulse overflow
Adjust pulse settings
W22 - Batch timeout
22
Check installation
23 W23 - Batch overrun
Check installation
24 W24 - Batch neg. flow
Check flow direction
30 W30 - Flowsaturated
Adjust max. flow
31 W31- Empty pipe
32 W32 - Temp. to high
Adjust temperature
33 W33 - Temp. to low
Adjust temperature
34 W34 - Zero Adj. fail
Check flow = zero
35 W35 - Current Out 1
Check max. settings
W36 - Freq/Pulse Out1
36
Check max. settings
40 P40 - SENSORPROM
Insert
41 P41 - Parameter range
Switch off and on
42 P42 - Current output
Check cables
43 P43 - Internal error
Switch off and on
49 P49 - Protec. viol.
Switch off and on
50 P50 - Temp. cable
Check cable
51 P51 - Pick-up 1
Check cable/install.
52 P52 - Pick-up 2
Check cable/install.
60 F60 - CAN comm. error
Converter/add-on module
61 F61 - SENSORPROM
Replace
F62 - SENSORPROM
62
Replace
63 F63 - SENSORPROM
Replace
70 F70 - Pick-up phase
F71 - Driver phase
71
80-83 F80, 81, 82, 83 - Internal error Restart or replace
84 F84 - Sensor level
97 F97 - Add-on module to old
Error code level:
W = Warning, F = Fatal, P = Permanent
SFIDK.PS.028.Q1.02
#Comment
Power on has activated
A new module has been added to the system
An add-on module is defect or has been removed.
This can also be an internal add-on module
A less vital parameter in the converter has been re-
placed by its default value
During initialisation the check of the saved totalize
value has failed. It is not possible to rely on the
saved totalizer value any more. The totalizer value
must be reset manually in order to rely on future
readings
During initialisation the check of the saved totalize
value has failed. It is not possible to rely on the
saved totalizer value any more. The totalizer value
must be reset manually in order to rely on future
readings
Actual flow is too big compared with pulse width and
mass/pulse
Duration of batching has exceeded a predefined
max. time
Batch quantity has exceeded a predefined maximum
overrun mass or volume
Negative flow direction during batch
Flow is above Q settings
max.
Pipe is empty
The temperature of the fluid has exceeded the max.
temperature rating of the sensor (180 °C)
The temperature of the fluid has exceeded the min.
temperature rating of the sensor (-50 °C)
The zero-point adjustment values are outside the limit
because there is not zero flow in the sensor. Check
zeroflow conditions, valves, pumps etc.
Current output exceeds 120%. Ensure that the sensor is
correctly sized and check max. flow setting
Freq/Pulse output exceeds 120%. Ensure that the sensor
is correctly sized and check max. flow setting
    

SENSORPROM unit not installed
A parameter is out of range.
The error will disappear at the next power-on
Current loop is disconnected or the loop resistance
is too big
Internal error
Too many errors occured at the same time.
Some errors are not detected correctly
Error in temperature sensor, check cables and
connectors
Pick-up 1 amplitude too low. Check cables or application
for damping (air/gas in liquid)
Pick-up 2 amplitude too low. Check cables or application
for damping (air/gas in liquid)
CAN bus communication error. An add-on module, the
display module or the converter is defect
    
err. It is not possible to rely on the data in SENSOR-

PROM unit
     
ID
The SENSORPROM
product ID. The SENSORPROM
type of product SITRANS F C MASSFLO,
SITRANS F US SONOFLO etc.
    
It is not possible to read from the SENSORPROM
unit
Check cables/polarity
Check cables/polarity
Pick-up amplitud saturated
Replace
unit ID do not comply with the

unit is from another

Outputs Input
status status
Active Active
Active Active
Active Active
Active Active
Active Active
Active Active
Reduced
pulse width Active
Batch out-
put on zero Active
Batch out-
put on zero Active
Active Active
Max. 120 % Active
Zero Active
Active Active
Active Active
Active Active
Active Active
Active Active
Active Active
Active Active
Active Active
Active Active
Active Active
Active Active
Active Active
Active Active
Zero Inactive
Active Active
Zero Inactive
Active Active
Active Active
Active Active
Active Active
Active Active
Active Active
25