Furuno FELCOM 12 Installation Manual

Mobile earth station

Hide thumbs Also See for FELCOM 12:

Operator's manual (182 pages)

Service manual (118 pages)

Brochure & specs (4 pages)

Quick Links

See also: Service Manual , Operator's Manual

INSTALLATION MANUAL

INMARSAT-C

MOBILE EARTH STATION

FELCOM 12

1. SYSTEM CONFIGURATION ................................. 1

2. EQUIPMENT LIST ................................................. 2

3. MOUNTING THE EQUIPMENT ............................. 3

4. WIRING ................................................................. 7

5. INSTALLATION OF GPS BOARD ASSEMBLY

(OPTION) ............................................................. 11

6. CHANGING POWER SPECIFICATION ............. 12

Installation Materials, Spare Parts,

Accessories ........................................................... A-1

Outline Drawings ................................................... D-1

Interconnection and Schematic Diagrams .......... S-1

NISHINOMIYA, JAPAN

Need help?

Do you have a question about the FELCOM 12 and is the answer not in the manual?

Questions and answers

Summary of Contents for Furuno FELCOM 12

Page 1: Table Of Contents
INSTALLATION MANUAL INMARSAT-C MOBILE EARTH STATION FELCOM 12 1. SYSTEM CONFIGURATION ......... 1 2. EQUIPMENT LIST ..........2 3. MOUNTING THE EQUIPMENT ......3 4. WIRING ..............7 5. INSTALLATION OF GPS BOARD ASSEMBLY (OPTION) ............. 11 6. CHANGING POWER SPECIFICATION ..... 12 Installation Materials, Spare Parts, Accessories ............
Page 2 Yo u r L o c a l A g e n t / D e a l e r 9 - 5 2 , A s h i h a r a - c h o , N i s h i n o m i y a , J a p a n Te l e p h o n e : 0 7 9 8 - 6 5 - 2 1 1 1 Te l e f a x :...
Page 3: Felcom
SAFETY INSTRUCTIONS CAUTION WARNING Do not work inside the Ground the equipment to equipment unless totally prevent electrical shock familiar with electrical and mutual interference. circuits. Confirm that the power supply voltage Hazardous voltage which can is compatible with the voltage rating cause electrical shock, burn of the equipment.
Page 4: System Configuration
1. SYSTEM CONFIGURATION Antenna Unit IC-112 Ground wire Terminal Unit IB-581 Keyboard Printer PP-510 Communication Unit IC-212 24 VDC Ship’s mains Distress Alert Unit 24 VDC IC-302 Received Call Unit IC-303 AC/DC Power Terminal Unit Supply Unit IB-581 PR-300 24 VDC Ship’s mains EGC Printer 100/200 VAC...
Page 5: Equipment List
2. EQUIPMENT LIST Standard Supply . t s & i t a . t s t s i l l a l l a i t a — — — Optional Equipment s t r t t i l l a .
Page 6: Mounting The Equipment
3. MOUNTING THE EQUIPMENT 5) Avoid the location near funnels and stacks; Mounting Location smoke and soot on the radome can lower sig- nal level. Antenna unit 6) Never mount the antenna unit on a metal 1) Mount the omnidirectional antenna high atop plate more than 20 cm square.
Page 7 • Avoid installing the unit near air conditioners and hot air vents. • Select a location free of water splash and rain. • Select a location where vibration is minimal. FURUNO label • Locate the unit well away from magnetic fields (generator, etc.). Eye mark •...
Page 8 7. Coat bolts with sealant (supplied) POLE DIAMETER (Ø60-90) HOSE CLAMP Ground wire (370 mm) PIPE FIXTURE 1 Ground stud Apply sealant : Antenna Antenna installation mounting Antenna Mast Materials pipe PIPE Tape here to prevent FIXTURE 2 cable damage. After connnecting, wrap Fasten the cable with connector with self-...
Page 9 2. Fix the bottom chassis to the mounting lo- Terminal unit cation with four tapping screws (supplied). Leave at least 80 mm at the sides and rear to 3. Run the interconnection cable thru a cable permit the checking and maintenance. entrance (see note below) and connect it to 1.
Page 10: Wiring
4.WIRING Antenna Unit Distress Distress Received IC-112 Alert Alert Call Unit Unit Unit IC-302 IC-302 IC-303 0.37 m Ground wire 5D-FB-CV, 30 m 8D-FB-CV, 50 m TTYCS-3 12D-SFA-CV, 100 m (local supply) Communication Unit IC-212 XXXXXX XXXX XXXX XXXX XXXXXX XXXXXX XXXX XXXX...
Page 11 Cable Fabrication, Connector Attachment Antenna cable connector at the Communication unit How to attach the antenna cable connector N-P-5DFB/N-P-8DFB Outer Sheath Dimensions in millimeters. Armor Remove outer sheath and armor by the Inner Sheath Shield dimensions shown left. Expose inner sheath and shield by the dimensions shown left.
Page 12 How to attach the antenna cable connector N-P-12DSFA Outer Sheath Dimensions in millimeters. Remove outer sheath and armor by the Armor Inner Sheath Shield dimensions shown left. Expose inner sheath and shield by the dimensions shown left. Twist shield end. Slip on clamp nut, gasket and clamp as shown left.
Page 13 Connection between the Communication unit and the Distress alert unit/ Received call unit At the Communication unit (Connector SRCN6A16-7P) 2 cm BRAIDED SHIELD VINYL SHEATH SOLDERING-SIDE EARTH CLAMP FIXING SOLDER UNUSED WIRE SCREW CORES AND EARTH CLAMP SET WIRE TO BRAIDED SCREW SHIELD VINYL SHEATH...
Page 14: Installation Of Gps Board Assembly (Option)
5. INSTALLATION OF GPS BOARD ASSEMBLY (OPTION) A GPS receiver board can be installed in the 4. Fix the cable assy. S.FL2-2LP0.7DWHA Communication Unit IC-212. There are two (400) between J1 of the GPS pcb and J4 of kind of GPS board assemblies: OP16-16-1 and the RFCONV pcb and secure it with three OP16-16-2.
Page 15: Changing Power Specification
6. CHANGING POWER SPECIFICATION When the ship's mains is 100/110/200/220 VAC, use AC/DC Power Supply Unit PR-300 (option) and change both tap connections on its transformer and fuse according to ship's mains. 100V 110V 100VAC SHIP'S MAINS 110VAC SHIP'S MAINS 200V 220V 200VAC SHIP'S MAINS...

This manual is also suitable for:

Inmarsat-c felcom 12