Setting Passwords - Sony HSR-1 Service Manual

Settings
2
Select the value or mode by pressing the b or B
key.
TAPE LENGTH
Set the tape length of the cassette to be used in units of
10 minutes.
When you change the TAPE LENGTH value, the REC
CYCLE value is recalculated and automatically
updated.
The longer the tape length you set, the longer the
recording cycle becomes.
Note
For recording, be sure to use a cassette of the same
tape length specified on this menu. If a cassette of a
different tape length is used, the TIME MODE
indication will not match the actual recording time.
The number included in the name of a DV- or DVM-
series model indicates the tape length (unit: minute).
(Ex.: 270 minutes with DV-270RM).
In case of a PDV- or PDVM-series model, the value
obtained by multiplying the number included in the
name by 1.5 corresponds the tape length (unit:
minute). (Ex.: 276 minutes with PDV-184N).
TIME MODE
Set the time to record on a cassette of the specified
tape length.
When you change the TIME MODE value, the REC
CYCLE value is recalculated and automatically
updated.
The smaller the TIME MODE value you set, the
shorter the recording cycle becomes.
REC CYCLE
Set the recording cycle per camera change.
Recording is made switching all the specified camera
in turn with the same specified cycle.
When you change the REC CYCLE value, the TIME
MODE value is recalculated and automatically
updated.
The shorter the cycle you set, the smaller the TIME
MODE value becomes.
Note
With the HSR-2/2P, the minimum value of the
recording cycle valid for Playback During Recording
mode is displayed in parentheses below the currently
set value. Set the recording cycle to a value that is
larger than the value in parentheses before actrivating
Playback During Recording mode.
5-14
Chapter 5 Connections and Preparations
For details, see "Requirements for Playback During
Recording" on page 2-12.
IMAGE QUALITY mode
Four IMAGE QUALITY modes (Horizontal × Vertical
resolution) are available. The selected mode is used
for all the specified camera.
When you change the IMAGE QUALITY mode, the
REC CYCLE value is recalculated and automatically
updated.
The lower the mode you select, the longer the REC
CYCLE value becomes.
Mode HSR-1/2 HSR-1P/2P
720 × 240 720 × 288
SUPER
360 × 240 360 × 288
HIGH
180 × 240 180 × 288
MID
180 × 120 180 × 144
LOW
To register the specified requirements
When the settings are completed, press the SET key.
A message "NOW SAVING" is displayed, and the
settings are stored in nonvolatile memory.
The Recording Function menu is restored.
Note
If the TIME MODE or REC CYCLE value exceeds the
limit after recalculation, " " will be displayed, and the
*
settings will not be stored even if you press the SET
key.
To restore to the previous settings
Before pressing the SET key, press the MENU key.
The message "ABORT !" is displayed, and the
previous settings are restored.

Setting Passwords

You can set passwords to release the key-lock function
that is activated by pressing the LOCK key.
As you can classify the recorder's key functions for
three levels each having a different password to release
the locks, operations of the functions can be limited by
the levels, such as Level 1 for the operator, Level 2 for
the administrator, and Level 3 for the system manager.
For the level settings, use FUNCTION LEVEL SET of
the Function Control Menu (page 4-11).
Then, set the passwords using PASSWORD SET of
the same menu.
To set a new password
1
Highlight FUNCTION CONTROL MENU (or
display FuncMenu) of the top menu by pressing
the V or v key, then press the b key.
The Function Control menu is displayed.
SETUP MENU
FUNCTION CONTROL MENU
AUTO REW : ON
POWER ON REC : OFF
BEEP : ON
STILL : FRAME
PRIORITY 1) : PLAY
1)
PRE REV TIME : 5 MIN
FUNCTION LEVEL SET
PASSWORD SET
1) HSR-2/2P only
2
Highlight PASSWORD SET (or display Password)
by pressing the v key, then press the b key.
The menu shifts to password setting.
SETUP MENU
FUNCTION CONTROL MENU
PASSWORD SET
M m
LEVEL 1
LEVEL 2
LEVEL 3
3
Highlight the level for which a password is to be
set, then press the b key.
The password setting display for the selected level
appears.
PASSWORD
INPUT NEW PASSWORD
– – – –
SHIFT : M
INPUT : NUM KEY
TO MENU : MENU KEY
DATA SET : SET KEY
CLEAR : RESET KEY
4
Enter a 4-digit number from the left digit by using
the numeric keys.
To enter 0, press 0.
The display for the entered digit changes to * both
on the monitor display and character display.
The B key acts as a backspace key.
5
Press the SET key.
A request message for repeated input of the same
password appears, and the number input area
returns to "– – – –."
6
Enter the same number again and press the SET
key.
A message "NOW SAVING" is displayed, and the
password is stored in nonvolatile memory.
Repeat steps 2 to 6 for each of the levels as required.
To change or delete the password
1
Call the password setting display by performing
step 1 and 3 of "To set a new password."
A message requesting the password appears, and
the input area "– – – –" appears.
2
Enter the password currently set using the numeric
keys and press the SET key.
The recorder enters the status in step 3 of "To set a
new password."
(Continued)
5-15
Chapter 5 Connections and Preparations