Remote Control Menu (Enhanced Menu) - Sony HSR-1 Service Manual

Menu Items
Display Char. display
Layer 2 Layer 3 Layer 4
NON >>>NON
Common to all
LEVEL1 >>>Level1
FUNCTION LEVEL SET
Layer 3 items
LEVEL2 >>>Level2
LEVEL3 >>>Level3
>Password
PASSWORD SET
LEVEL1 >>Levell
>>Level2
LEVEL2
LEVEL3 >>Level3
1) If no password has been specified at the respective levels, the function(s) is(are) valid even in LOCK mode.
The following two items are only for the HSR-2/2P, and are not displayed with the HSR-1/1P.
Display Char. display
Layer 2 Layer 3
>Priority
PRIORITY
>>PB
PLAY
REC >>Rec
PRE REV TIME >PreRevTime
n MIN (5) >>n
4-12
Chapter 4 Menu Operations
Contents
Applies no password restriction. Operable even in LOCK mode.
Enables the function(s) in LOCK mode with any of the
1)
passwords of level 1, 2, and 3.
Enables the function(s) in LOCK mode with either of the
1)
passwords of level 1 and 2.
Enables the function(s) in LOCK mode only with the password of
level 3. 1)
For entering passwords to release the locks of three levels.
For the setting procedure, see "Setting Passwords" on page 5-15.
Contents
Selects the priority of operations when the preset recording
cycle is smaller than the valid minimum value in Playback During
Recording mode.
Changes the recording cycle and continues recording. Playback
is performed in Playback During Recording mode.
Maintains the recording cycle unchanged and continues
recording. Playback during Recording is not performed.
Sets the pre-reverse time for playback in Playback During
Recording mode.
n = pre-reverse time (1-99 minutes)
For the setting procedure, see "Setting the Pre-Reverse Time"
on page 5-17.

Remote Control Menu (Enhanced Menu)

The Remote Control Menu is an enhanced menu and is
displayed only when MENU GRADE is set to ENH on
the top menu.
Monitor Display
SETUP MENU
REMOTE CONTROL MENU
RS232C : 9600
PARALLEL INPUT
PARALLEL OUTPUT
PARALLEL OUT VOLTAGE
Display Char. display
Layer 2 Layer 3 Layer 4
>RS232C
RS232C
n BPS (9600) >>n bps
>Para Input
PARALLEL INPUT
INm (n PIN) >>n PIN
NO USE >>>No use
STOP >>>STOP
>>>REC
REC
PLAY >>>PLAY
>>>F.FWD
F.FWD
REW >>>REW
>>>F.FRAME
F.FRAME
R.FRAME >>>R.FRAME
SERIES REC >>>SerRec
TIME ADJUST >>>Time Set
ALARM RETURN >>>AlmRtn
>>>Alarm L
ALARM (L)
ALARM n (L) >>>Alm n L
ALARM (H) >>>Alarm H
>>>Alm n H
ALARM n (H)
Character display
Remote Menu
↓
Press the b key.
>RS232C
The Remote Control menu item selected when you left the
menu the last time is displayed.
The setting shown in bold characters in the Layer 3 or 4
column of the table is the standard setting and is displayed
with an asterisk on the monitor screen.
Contents
For setting the baud rate for the RS-232C interface.
n = 1200/2400/4800/9600/19200/38400
For assigning a function to each input pin (24 inputs) of the
PARALLEL I/O connector on the rear panel.
m = 1 to 24, n = pin number 2 to 13, 21 to 32
Ignores the input signal.
Command inputs corresponding to the tape transport
control keys on the front panel (Active L)
Series-recording signal input (Active L)
Clock set signal input (Active L).
The internal clock will be set to 00 minute 00 second within ±15
minutes when the signal is input.
Alarm return input (Active L)
Alarm input common to all cameras (Active L)
Independent alarm input to camera n (Active L)
n = Camera No. 1 to 16
Alarm input common to all cameras (Active H)
Independent alarm input to camera n (Active H)
n = Camera No. 1 to 16
(Continued)
4-13
Chapter 4 Menu Operations