Page 1
JCY-1800/1850 VDR/S-VDR VDR/S-VDR VDR/S-VDR Real Time Monitor VDR/S-VDR Real Time Monitor Installation Manual Installation Manual Version 1.2 Version 1.2...
Page 3
Record of Revisions Record of Revision Description Date Approved by Checked by First Edition 07-Feb-1 M.Takayama R.Uchijima Added example of connection 07-Jul-23 M.Takayama R.Uchijima VDR/S-VDR Real Time Monitor / Installation Manual...
Page 4
Before Using < Before Using > Icons This manual and product employ various icons to enable users to use the product safety and correctly, and to prevent any harm to users or others, and to prevent damage to the property. The icons and the meanings are indicated below.
Page 5
Notes on Using < Notes on Using > Do not disassemble or remodel this equipment. Such action may cause fire, electric shock, or an equipment fault. Do not use any AC/DC adaptor other than attachment. Such action may cause fire, electric shock, or an equipment fault. Do not use any power supply voltage other than the specified voltages.
Page 6
Before Using CAUTION Do not install the equipment in the location affected by water, humidity, dust, or soot. It may become the cause of fire, electric shock, or a fault. Do not put in from a vent foreign substance, such as metal or a thing which is easy to burn.
2.3 In case of connecting with Radar IF (NWP-46) ................5 Chapter3 Wiring Diagrams .......................7 Chapter 4 Wiring ........................11 4.1 In case of JCY-1800 VDR ......................11 4.2 In case of JCY-1850 S-VDR......................12 4.3 Wiring to VDR IF(Router)......................13 Chapter5 Setup VDR/S-VDR by Maintenance software ............15...
Contents Chapter9 Appendix.........................61 9.1 How to eject CF card from VDR/S-VDR ..................61 9.2 Example of connection ........................ 63 9.2.1 Example1 In case of only one VDR/S-VDR Real Time Monitor............65 9.2.2 Example2 In case of connecting with Client PC ................70 9.2.3 Example3 In case of connecting with Client PC and Radar IF ............
Chapter1 Installation Procedure Chapter1 Installation Procedure General Procedure (1) Mounting the necessary unit (2) Wiring the cable connected unit in according with installation drawings (3) Checking wiring condition (4) Setup of VDR/SVDR by Maintenance software (5) Setup of PC in which the VDR/S-VDR Real Time Monitor is installed (6) Final check This installation manual is described for version 1.2 of VDR/S-VDR Note...
Page 10
Chapter1 Installation Procedure Blank Page VDR/S-VDR Real Time Monitor / Installation Manual...
Chapter2 System Composition Chapter2 System Composition Since the system configuration is possible various combinations, it explains here by some typical compositions. 2.1 Basic Composition Voyage Data VDR/S-VDR JCY-1800/1850 Radar Image Audio(VHF) Capsule Record Data VDR Network Real Time Monitor Fig. 2.1-1 Table 2.1-1...
In that case, one Server PC is necessary to deliver data to the Client PCs. In addition, the number of monitor terminal as Client PC that can be connected with Server PC is three or less. Voyage Data User LAN VDR/S-VDR JCY-1800/1850 Radar Image Audio (VHF) Monitor (Server)
Radar, ECDIS and Conning by Radar IF in the VDR/S-VDR Real Time Monitor. And, VDR IF (Router) is needed to separate the Radar IF from user LAN. Voyage Data Radar Image VDR/S-VDR JCY-1800/1850 Audio Radar IF Capsule Record...
Page 14
Chapter2 System Composition Blank Page VDR/S-VDR Real Time Monitor / Installation Manual...
PC (*2) NOTE 1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply 2. *2 PC : Owner supply 3. *3 JCY-1800 : EXT-LAN JCY-1850 : JRC-LAN VDR/S-VDR Real Time Monitor INTERCONNECTION DIAGRAM Fig. 3.1 Basic Composition VDR/S-VDR Real Time Monitor / Installation Manual...
Page 16
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply Client PC3 (*2) 2. *2 PC : Owner supply 3. *3 JCY-1800 : EXT-LAN JCY-1850 : JRC-LAN VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM Fig. 3.2 In case of connecting with user LAN...
Page 17
Client PC2 (*2) NOTE 192.168.0.248 1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply 2. *2 PC : Owner supply 3. *3 JCY-1800 : EXT-LAN VDR/S-VDR JCY-1850 : JRC-LAN Real Time Monitor Client PC3 (*2) VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM Fig.
Page 18
Chapter3 Wiring Diagrams Blank Page VDR/S-VDR Real Time Monitor / Installation Manual...
Chapter4 Wiring Chapter 4 Wiring 4.1 In case of JCY-1800 VDR Open the door of VDR, and connect LAN cables as following. Maintenance PC: Connect LAN cable to “VDR-LAN” (Not used port) of MCB. VDR/S-VDR Real Time Monitor PC: Connect LAN cable to “EXT-LAN” port of RMB.
Open the door of S-VDR, and connect LAN cables as following. Maintenance PC: Connect LAN cable to “VDR-LAN” (Not used port) of MCB. VDR/S-VDR Real Time Monitor PC: Connect LAN cable to “JRC-LAN” port of MCB. Maintenance PC: VDR-LAN へ VDR/S-VDR Real Time Monitor PC:...
Chapter4 Wiring 4.3 Wiring to VDR IF(Router) It is necessary to connect VDR IF (Router) for connecting the Radar IF (NWP-46) to VDR/S-VDR. VDR/S-VDR JCY-1800/1850 Server PC Radar IF NWP-46 Client PC The power cable for the object for AC100 and AC200V is Note attached to the VDR IF.
Page 22
Chapter4 Wiring RCU upside is recommended as installation place. To wire AC power cable of the VDR IF, secure 7cm for back space of the VDR IF, and fix it. 【Note】 If the VDR IF is fixed as the following figure, backs space of the VDR IF will be secured 7cm. In order to fix the VDR IF, please use the attached magic tape in the VDR IF kit.
(1)Click the”JCY1800 Maintenance” icon, and start the maintenance software. (2)Select “VDR” or “S-VDR” in the Setup Equipment block of Login screen, and log in the software. In case of JCY-1800: Select VDR In case of JCY-1850: Select S-VDR Select VDR or S-VDR.
Page 24
Chapter5 Setup VDR/S-VDR by Maintenance software (3)Click the [Option PC(VDR Real Time Monitor)] button in the Home screen. [Option PC(VDR Real Time Monitor)] button (4)Click the [Receive] button in the Option screen, and read current setup data. [Receive] button VDR/S-VDR Real Time Monitor / Installation Manual...
Page 25
Chapter5 Setup VDR/S-VDR by Maintenance software (5) Check the IP Address of the Option PC and VDR WAN. VDR WAN :IP Address of VDR LAN port for connecting the Option PC Option PC :Destination IP Address of real time data If the IP Address is changed, click the [Edit] button, and change it in the Network screen.
Page 26
Chapter5 Setup VDR/S-VDR by Maintenance software (6) Input check for real time output of necessary data. Every data can be selected, and moreover all output can be set up by package with the [All Enable] button and [All Disable] button. [All Enable]: “✓”...
Chapter6 PC (Server/Client) Setup Chapter6 PC (Server/Client) Setup 6.1 PC Specification Confirm that the specification of an installed PC is the following performance equivalent model. Windows XP Professional or Home Edition Pentium M Processor 730 Clock=1.6GHz 512MB 40GB Resolution 1024×1024 dots (More than XGA) CD drive CD-ROM Card drive...
Page 28
Chapter6 PC (Server/Client) Setup (1) Click the “Network and Internet Connections” in the Control Panel screen. Network and Internet Connections (2) Click the “Network Connections”. Network Connections (3) Right-click the “Local Area Connection”, and select the Properties menu. VDR/S-VDR Real Time Monitor / Installation Manual...
Page 29
Chapter6 PC (Server/Client) Setup (4) Select the “Internet Protocol (TCP/IP)”, and click the [Properties] button. (5) Enter the IP address and the Subnet mask, and click the [OK] button. If the IP address which is different from default is already assigned in the user LAN, click the [Advance] button and go to (6).
Page 30
Chapter6 PC (Server/Client) Setup (6) Register the IP address shown in the Table 6.2-1. IP address Server=192.168.0.251 Client1=192.168.0.250 Client2=192.168.0.249 Client3=192.168.0.248 The IP address setup is completion. VDR/S-VDR Real Time Monitor / Installation Manual...
Chapter6 PC (Server/Client) Setup 6.2.2 Stop automatic synchronization with an Internet time server Shows how to stop automatic synchronization with an Internet time server. (1) Click the clock indication at the lower right of a screen. (2) The “Date and Time Properties” screen is indicated, and select the “Internet Time” tab. (3) Remove the “Automatically synchronize with an Internet time server”...
Chapter6 PC (Server/Client) Setup 6.2.3 Stop the Remote Assistance (1) Click the “Performance and Maintenance” in the Control Panel screen. Performance and Maintenance (2) Click the “System”. System VDR/S-VDR Real Time Monitor / Installation Manual...
Page 33
Chapter6 PC (Server/Client) Setup (3) Select the Remote tab. (4) Remove the “Remote Assistance” check, and click the [OK] button. The Remote Assistance is stopped. VDR/S-VDR Real Time Monitor / Installation Manual...
Chapter6 PC (Server/Client) Setup 6.2.4 Stop the Automatic Updates (1) Click the “Performance and Maintenance” in the Control Panel screen. Performance and Maintenance (2) Click the “System”. System VDR/S-VDR Real Time Monitor / Installation Manual...
Page 35
Chapter6 PC (Server/Client) Setup (3) Select the Automatic Updates tab. (4) Select the “Turn off Automatic Updates”, and click the [OK] button. The Automatic Updates is stopped VDR/S-VDR Real Time Monitor / Installation Manual...
Chapter6 PC (Server/Client) Setup 6.2.5 Stop the Error Reporting (1) Click the “Performance and Maintenance” in the Control Panel screen. Performance and Maintenance (2) Click the “System”. System VDR/S-VDR Real Time Monitor / Installation Manual...
Page 37
Chapter6 PC (Server/Client) Setup (3) Select the “Advanced” tab. (4) Click the [Error Reporting] button. [Error Reporting] button VDR/S-VDR Real Time Monitor / Installation Manual...
Page 38
Chapter6 PC (Server/Client) Setup (5) Select the “Disable error reporting”, and remove the “But notify me when critical errors occur” check. And click the [OK] button. (6) Click the [OK] button, and close the System Properties screen. The Error Reporting” is stopped. VDR/S-VDR Real Time Monitor / Installation Manual...
Chapter6 PC (Server/Client) Setup 6.2.6 Invalidate the Windows Firewall The setup screen for the Windows Firewall changes with versions of Service Pack of Windows XP. Invalidate the Firewall after confirming version of Service Pack. It is possible to confirm version of Service Pack by the following Note operations.
Page 40
Chapter6 PC (Server/Client) Setup (3) Right-click the “Local Area Connection”, and select the Properties menu. (4) Select the Advanced tab, and remove the Windows Firewall check. The Firewall is invalidated. VDR/S-VDR Real Time Monitor / Installation Manual...
Page 41
Chapter6 PC (Server/Client) Setup 6.2.6.2 In case of Service Pack2 (1) Click the “Network and Internet Connections” in the Control Panel screen. Network and Internet Connections (2) Click the Windows Firewall. Windows Firewall VDR/S-VDR Real Time Monitor / Installation Manual...
Page 42
Chapter6 PC (Server/Client) Setup (3) The Windows Firewall screen is indicated, and select “Off (Not recommended)”, and click the [OK] button. The Firewall is invalidated. VDR/S-VDR Real Time Monitor / Installation Manual...
Chapter6 PC (Server/Client) Setup 6.2.7 Set the Power Options In case of Server PC, it is necessary to prevent a system standby, a system hibernation, etc during employment. (1) Click the “Performance and Maintenance” in the Control Panel screen. Performance Maintenance (2) Click the “Power Options”...
Page 44
Chapter6 PC (Server/Client) Setup (3) Select “Never” in the all items of the “Turn off hard disks”, the “System Standby” and the “System hibernates”, and click the [OK] button. The Power Options setup is completion. VDR/S-VDR Real Time Monitor / Installation Manual...
Chapter6 PC (Server/Client) Setup 6.3 Install the VDR/S-VDR Real Time Monitor software Install the VDR/S-VDR Real Time Monitor software in a PC in accordance with the following operation. (1) Insert the Install CD-ROM in a CD drive. (2)After a while, Installer starts and the following web screen opens automatically by AUTORUN.
Page 46
Chapter6 PC (Server/Client) Setup (4) The installer for the VDR Real Time Monitor starts, and the preparation for the installation is started. (5) The opening screen is indicated, and click the [Next] button. (6) The InstallShield Wizard for the VDR Real Time Monitor starts, and click the [Next] button. VDR/S-VDR Real Time Monitor / Installation Manual...
Page 47
Serial Number field, and click the [Next] button. Note License number is composed by ”JRC-****-****”. The number is displayed in the place of “The license number for Real Time Monitor is as follows:” of the install CD-ROM.
Page 48
Chapter6 PC (Server/Client) Setup (9) Install is started, and progress bar is indicated. (10) Click the [Server] button or the [Client] button in accordance with the content shown in the "6.2.1 IP address Setup". (11) The InstallShield Wizard completion screen is indicated, and click the [Finish] button. Installation of the VDR/S-VDR Real Time Monitor software is completion.
To uninstall the VDR/S-VDR Real Time Monitor software, operate as follows. (1) Click the “Add or Remove Programs” in the Control Panel screen. (2) Select the “JCY-1800 VDR_Monitor”, click the [Remove] button. (3) Since some files are remained in the installation folder, remove the folder with the My Computer.
Chapter6 PC (Server/Client) Setup 6.5 Initial setup for the VDR/S-VDR Real Time Monitor Initial setup for the VDR/S-VDR Real Time Monitor is set up with the Setup software of VDR/S-VDR Real Time Monitor software attachment. Shows the setup flow. Server and Client PC) VDR/S-VDR configuration reading by communication (2) Various setups Completion...
Chapter6 PC (Server/Client) Setup 6..5.1 Setup Please initialize in accordance with the following operations. (1) Click the [Setup] button in the VDR Launcher. (2) Select the “Serviceman”, and log in after inputting serviceman information and the following password. Password:“jrcvdr”(Input everything by the small letter.) VDR/S-VDR Real Time Monitor / Installation Manual...
Page 52
Chapter6 PC (Server/Client) Setup (3) Reading of the VDR configuration. Server and Client PC) Eject a CF card from VDR/S-VDR, and insert it into the CF card slot of used PC. Then, to import VDR/S-VDR configuration data, select the “SysInfo.dat” file in the CF card and click the [Import] button.
Page 53
Chapter6 PC (Server/Client) Setup Blank Page VDR/S-VDR Real Time Monitor / Installation Manual...
Page 54
Chapter6 PC (Server/Client) Setup (4) Input the necessary items in the System tab. Refer to the Table6.3 for setup contents. ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ VDR/S-VDR Real Time Monitor / Installation Manual...
Page 55
Chapter6 PC (Server/Client) Setup Table6.3 Setup Contents in the System Tab Block Content Setup*1 Note “✓” Sensor contents gotten ① Existing of A/D and Dry Contact is indicated. If the unit exists, displayed. from the VDR configu- ration. “✓” Audio Monitor ②...
Page 56
Chapter6 PC (Server/Client) Setup Explains how to set up the Visual block. Connection) Set the connection type of Radar unit. Shows the detail of connection type the following table so that select a type and set. Connection Connection Connection Type Note FGB1(VDR)...
Page 57
If the FGB2 is clicked, the input screen for the Radar IF information is displayed. Refer to the input example, and input the information. ・Connection :Case5 ・Model :NWP-46 ・Maker :JRC ・Serial No :MBXXXXX FGB2 (Option) VDR/S-VDR Real Time Monitor / Installation Manual...
Page 58
Refer to the input example, and input the information. To record the Radar image, input “✓” in the Record check box of Radar3 and Radar4. ・Connection :Case5 ・Model :JAN-701 ・Maker :JRC ・Serial No :KEXXXXX Record VDR/S-VDR Real Time Monitor / Installation Manual...
Page 59
Chapter6 PC (Server/Client) Setup Blank Page VDR/S-VDR Real Time Monitor / Installation Manual...
Page 60
Chapter6 PC (Server/Client) Setup (5) It is not necessary to change the Ethernet tab normally. Refer to the Table 6.4 for more detail. ① ② ③ ④ ⑤ ⑥ VDR/S-VDR Real Time Monitor / Installation Manual...
Page 61
Chapter6 PC (Server/Client) Setup Table6.4 Setup Contents in the Ethernet Tab Block Content Setup*1 Note Option PC LAN1 (VDR Side) It is the IP address for communication with the ① VDR. LAN2 (Terminal Side) It is the IP address for connecting with Client PC in the user LAN.
Page 62
Chapter6 PC (Server/Client) Setup (6) Check the quantity of engine, rudder, thruster and propeller, Trans-Keel and sentence from sensors in the Configuration tab. Quantity Note If a setup content is wrong, the VDR/S-VDR Real Time Monitor can not indicate a data correctly of the wrong content. Please set the wrong setup correctly by the Maintenance software.
Page 63
Chapter6 PC (Server/Client) Setup Note About Keel – Trans It means distance from keel to transducer as the following figure. Echo sounder outs depth under transducer, so that depth under keel can be indicated always by registration the distance. (7) Set the inputted contents In case of Server PC)...
Page 64
Chapter6 PC (Server/Client) Setup (9) Return the CF card to the VDR/S-VDR. Caution When data copying is finished, please be sure to insert a CF card to the VDR/S-VDR. If the CF card is continued to eject more than 10 minutes, “MEDIA” alarm occurs in the VDR/S-VDR.
Chapter7 Final Check Chapter7 Final Check When the installation is completion, start the VDR Real Time Monitor by the [MONITOR] button of the VDR_Launcher. Please check the operation of the VDR/S-VDR Real Time Monitor in accordance with the checklist of the Table 7.1. When the VDR/S-VDR Real Time Monitor is installed with the record function, in order to prevent record missing, the Back Up screen is indicated at opening.
Page 66
Chapter7 Final Check Table 7.1 Checklist for the VDR Real Time Monitor VDR Real Time Monitor Judgment Item Content Server Client1 Client2 Client3 Real time Is the indication of sensor data possible? indication Is the audio monitoring possible? Is the monitor prevented depending on a customer demand? Is the indication of the FGB1 image possible? Is the indication of the FGB2 image possible?
Chapter8 Trouble Shooting Chapter8 Trouble Shooting Table8.1 In case of Server Symptom Cause Action The real time indication is not Faulty wiring of a LAN cable Check the connections. possible. Initial setup for real time Set the Option PC setup by the output is not completed by Maintenance software.
Page 68
Chapter8 Trouble Shooting Table6-2 In case of Client (Monitor Terminal) Symptom Cause Action The real time indication is not Faulty wiring of a LAN cable Check the connections. possible. The IP address setup of the Correct the IP address of the terminal by the Server side is terminal by the Setup software wrong.
Chapter9 Appendix Chapter9 Appendix 9.1 How to eject CF card from VDR/S-VDR (1) Push the [CARD STOP] button. (2) The CARD LED blinks for 5 sec and goes out. Then ejection of CF card becomes possible. (3) Push the [EJECT] button, and eject a CF card. CF card Slot EJECT button CARD LED (Green)...
Page 70
Chapter9 Appendix Blank Page VDR/S-VDR Real Time Monitor / Installation Manual...
Real Time Monitor PC (*2) NOTE 1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply 2. *2 PC : Owner supply 3. *3 JCY-1800 : EXT-LAN JCY-1850 : JRC-LAN VDR/S-VDR Real Time Monitor INTERCONNECTION DIAGRAM VDR Real Time Monitor / Installation Manual...
Page 74
Chapter9 Appendix STEP 1 Set by Maintenance software (1)Open the Option PC(VDR Real Time Monitor)screen (2)Click the [All Enable] button (3)Check that the following addresses in VDR WAN and Option PC ・ VDR WAN=192.168.0.254 ・ Option PC=192.168.0.251 VDR WAN /Option PC [All Enable] button (4) If the IP address is different, open the Network screen by the [Edit] button, and change IP...
Page 75
Chapter9 Appendix STEP 2 Set IP Address Open the properties screen of Internet protocol (TCP/IP) in the Windows control panel, and set the following IP address to the VDR/S-VDR Real Time Monitor PC. ・IP Address =192.168.0.251 ・Subnet Mask =255.255.255.0 It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor. IP Address /Subnet Mask And then set the VDR/S-VDR Real Time Monitor PC in accordance with the “6.2 Setup Items of...
Page 76
Chapter9 Appendix STEP 4 Set by the Setup software (1) System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・ Input “✓” when connection or record in the FGB block is needed, and input the Radar information.
Page 77
Chapter9 Appendix (2) Ethernet tab screen Check that the following IP address is set. ・LAN1(VDR Side)=192.168.0.251 ・VDR IF(Router) Connect=None 192.168.0.251 None (3) Click the [All Set] button, and setting of the VDR/S-VDR Real Time Monitor is completion. VDR Real Time Monitor / Installation Manual...
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply Client PC3 (*2) 2. *2 PC : Owner supply 3. *3 JCY-1800 : EXT-LAN JCY-1850 : JRC-LAN VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM VDR/S-VDR Real Time Monitor / Installation Manual...
Page 79
Chapter9 Appendix STEP 1 Set by Maintenance software (1)Open the Option PC(VDR Real Time Monitor)screen. (2)Click the [Receive] button to receive the VDR/S-VDR configuration data. (3)Click the [All Enable] button. (4)Check that the following addresses in VDR WAN and Option PC. ・...
Page 80
Chapter9 Appendix STEP 2 Set IP Address of Server PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set the following IP address to the Server PC. ・IP Address =192.168.0.251 ・Subnet Mask =255.255.255.0 It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor. IP Address /Subnet Mask And then set the Server PC in accordance with the “6.2 Setup Items of PC”.
Page 81
Chapter9 Appendix STEP 3 Set by the Setup software of Server PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for Server PC”, and set by the Setup software. (1) System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・...
Page 82
Chapter9 Appendix (2)Ethernet tab screen Check that the following IP address is set. ・LAN1(VDR Side)=192.168.0.251 ・VDR IF(Router) Connect=None 192.168.0.251 None (3) Click the [All Set] button, and setting of the Server PC is completion. VDR/S-VDR Real Time Monitor / Installation Manual...
Page 83
Chapter9 Appendix STEP 4 Set IP Address of Client PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set the following IP address to the Client PC. ・IP Address Client1=192.168.0.250 Client2=192.168.0.249 Client3=192.168.0.248 ・Subnet Mask =255.255.255.0 It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
Page 84
Chapter9 Appendix STEP 5 Set by the Setup software of Client PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client PC”, and set by the Setup software. (1)System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・...
Page 85
Chapter9 Appendix (2)Ethernet tab screen There is no setup in the Ethernet tab screen. (3)Click the [All Set] button, and setting of the Client PC is completion. Please set up other Client PC similarly. VDR Real Time Monitor / Installation Manual...
Client PC2 (*2) NOTE 1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply 192.168.0.248 2. *2 PC : Owner supply 3. *3 JCY-1800 : EXT-LAN VDR/S-VDR JCY-1850 : JRC-LAN Real Time Monitor Client PC3 (*2) VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM...
Page 87
Chapter9 Appendix STEP 1 Set by Maintenance software (1)Open the Option PC(VDR Real Time Monitor)screen. (2)Click the [Receive] button to receive the VDR/S-VDR configuration data. (3)Click the [All Enable] button. (4)Check that the following addresses in VDR WAN and Option PC. ・...
Page 88
Chapter9 Appendix STEP 2 Set IP Address of Server PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set the following IP address to the Server PC. ・IP Address =192.168.0.251 ・Subnet Mask =255.255.255.0 It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor. IP Address /Subnet Mask And then set the Server PC in accordance with the “6.2 Setup Items of PC”.
Page 89
Chapter9 Appendix STEP 3 Set by the Setup software of Server PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for Server PC”, and set by the Setup software. (1) System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・...
Page 90
Chapter9 Appendix (2)Ethernet tab screen Check that the following IP address is set. ・LAN1(VDR Side)=192.168.0.251 ・VDR IF(Router) Connect=”✓” WAN (FGB2 Side) = 192.168.111.100 LAN (Real Time Monitor Side) = 192.168.0.100 192.168.0.251 ”✓” (3) Click the [All Set] button, and setting of the Server PC is completion. VDR/S-VDR Real Time Monitor / Installation Manual...
Page 91
Chapter9 Appendix STEP 4 Set IP Address of Client PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set the following IP address to the Client PC. ・IP Address Client1=192.168.0.250 Client2=192.168.0.249 Client3=192.168.0.248 ・Subnet Mask =255.255.255.0 It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
Page 92
Chapter9 Appendix STEP 5 Set by the Setup software of Client PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client PC”, and set by the Setup software. (1)System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・...
Page 93
Chapter9 Appendix (2)Ethernet tab screen There is no setup in the Ethernet tab screen. (3)Click the [All Set] button, and setting of the Client PC is completion. Please set up other Client PC similarly. VDR Real Time Monitor / Installation Manual...
Page 94
Chapter9 Appendix STEP 6 Set firewall of the VDR IF(Router) The firewall of VDR IF is canceled when shipped from a factory. Please validate firewall by the following operation of telnet communication from the Server PC of the VDR/S-VDR Real Time Monitor. (1) To communicate by telnet from the Server PC of the VDR/S-VDR Real Time Monitor, input as follows on the command prompt screen.
Page 95
Chapter9 Appendix (6) Write the attached IP address seal as follows, and stick it on the VDR IF. WAN:192.168.111.100 LAN:192.168.0.100 VDR IF setup is completion above. Note To set firewall invalid, select the "18firof.cfg" as script file at the (3) and cancel firewall of the VDR IF.
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply Client PC3 (*2) 2. *2 PC : Owner supply 3. *3 JCY-1800 : EXT-LAN JCY-1850 : JRC-LAN VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM VDR/S-VDR Real Time Monitor / Installation Manual...
Page 97
Chapter9 Appendix STEP 1 Set by Maintenance software (1) Open the Option PC(VDR Real Time Monitor)screen. (2) Click the [Receive] button to receive the VDR/S-VDR configuration data. (3) Click the [All Enable] button. (4) Check that the following addresses in VDR WAN and Option PC. ・...
Page 98
Chapter9 Appendix STEP 2 Set IP Address of Server PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set the following IP address to the Server PC. If the IP address automatically is assigned by DHCP in the user LAN, cancel the DHCP. And register an unused fix IP address in the user LAN and add above IP address.
Page 99
Chapter9 Appendix (2) Click [Add] button, and add the following IP address and subnet mask. ・IP Address =192.168.0.251 ・Subnet Mask =255.255.255.0 It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor. And then set the Server PC in accordance with the “6.2 Setup Items of PC”. VDR Real Time Monitor / Installation Manual...
Page 100
Chapter9 Appendix STEP 3 Set by the Setup software of Server PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for Server PC”, and set by the Setup software. (1) System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・...
Page 101
Chapter9 Appendix (2)Ethernet tab screen Check that the following IP address is set. ・LAN1(VDR Side)=192.168.0.251 ・VDR IF(Router) Connect=None 192.168.0.251 None (3) Click the [All Set] button, and setting of the Server PC is completion. VDR Real Time Monitor / Installation Manual...
Page 102
Chapter9 Appendix STEP 4 Set IP Address of Client PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set the following IP address to the Client PC. If the IP address automatically is assigned by DHCP in the user LAN, cancel the DHCP. And register an unused fix IP address in the user LAN and add above IP address.
Page 103
Chapter9 Appendix (2) Click [Add] button, and add the following IP address and subnet mask. ・IP Address =192.168.0.251 ・Subnet Mask =255.255.255.0 It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor. And then set the Server PC in accordance with the “6.2 Setup Items of PC”. VDR Real Time Monitor / Installation Manual...
Page 104
Chapter9 Appendix STEP 5 Set by the Setup software of Client PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client PC”, and set by the Setup software. (1)System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・...
Page 105
Chapter9 Appendix (2) Ethernet tab screen There is no setup in the Ethernet tab screen. (3) Click the [All Set] button, and setting of the Client PC is completion. Please set up other Client PC similarly. VDR Real Time Monitor / Installation Manual...
Page 106
Chapter9 Appendix 9.2.5 Example5 In case of connecting with Client PC and Radar IF Server and Client PC already is assigned different IP address (192.168.20.xxx) from default value, and explains how to set when Server PC is connected to Client 1, Client 2, Client3 PC and Radar IF.
Page 107
Chapter9 Appendix STEP 1 Set by Maintenance software (1) Open the Option PC(VDR Real Time Monitor)screen. (2) Click the [Receive] button to receive the VDR/S-VDR configuration data. (3) Click the [All Enable] button. (4) Check that the following addresses in VDR WAN and Option PC. ・...
Page 108
Chapter9 Appendix STEP 2 Set IP Address of Server PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and add registration of IP address and subnet mask to the Server PC. If the IP address automatically is assigned by DHCP in the user LAN, cancel the DHCP. And register an unused fix IP address in the user LAN and add above IP address.
Page 109
Chapter9 Appendix (2) Click [Add] button, and add the following IP address and subnet mask. ・IP Address =192.168.0.251 ・Subnet Mask =255.255.255.0 It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor. And then set the Server PC in accordance with the “6.2 Setup Items of PC”. VDR Real Time Monitor / Installation Manual...
Page 110
Chapter9 Appendix STEP 3 Set by the Setup software of Server PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for Server PC”, and set by the Setup software. (1) System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・...
Page 111
Chapter9 Appendix (2) Ethernet tab screen Check that the following IP address is set. ・LAN1(VDR Side)=192.168.0.251 ・VDR IF(Router) Connect=”✓” WAN (FGB2 Side) = 192.168.111.100 LAN (Real Time Monitor Side) = 192.168.0.100 192.168.0.251 ”✓” (3) Click the [All Set] button, and setting of the Server PC is completion. VDR Real Time Monitor / Installation Manual...
Page 112
Chapter9 Appendix STEP 4 Set IP Address of Client PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and add registration of IP address and subnet mask to Client PC. If the IP address automatically is assigned by DHCP in the user LAN, cancel the DHCP. And register an unused fix IP address in the user LAN and add above IP address.
Page 113
Chapter9 Appendix (2) Click [Add] button, and add the following IP address and subnet mask. ・IP Address Client1=192.168.0.250 Client2=192.168.0.249 Client3=192.168.0.248 ・Subnet Mask =255.255.255.0 It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor. VDR Real Time Monitor / Installation Manual...
Page 114
Chapter9 Appendix STEP 5 Set by the Setup software of Client PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client PC”, and set by the Setup software. (1)System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・...
Page 115
Chapter9 Appendix (2) Ethernet tab screen There is no setup in the Ethernet tab screen. (3) Click the [All Set] button, and setting of the Client PC is completion. Please set up other Client PC similarly. VDR Real Time Monitor / Installation Manual...
Page 116
Chapter9 Appendix STEP 6 Set firewall of the VDR IF(Router) The firewall of VDR IF is canceled when shipped from a factory. Please validate firewall by the following operation of telnet communication from the Server PC of the VDR/S-VDR Real Time Monitor. (1) To communicate by telnet from the Server PC of the VDR/S-VDR Real Time Monitor, input as follows on the command prompt screen.
Page 117
Chapter9 Appendix (6) Write the attached IP address seal as follows, and stick it on the VDR IF. WAN:192.168.111.100 LAN:192.168.0.100 VDR IF setup is completion above. Note To set firewall invalid, select the "18firof.cfg" as script file at the (3) and cancel firewall of the VDR IF.
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply Client PC3 (*2) 2. *2 PC : Owner supply 3. *3 JCY-1800 : EXT-LAN JCY-1850 : JRC-LAN VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM VDR/S-VDR Real Time Monitor / Installation Manual...
Page 119
Chapter9 Appendix STEP 1 Set by Maintenance software (1) Open the Option PC(VDR Real Time Monitor)screen. (2) Click the [Receive] button to receive the VDR/S-VDR configuration data. (3) Click the [All Enable] button. (4) Check that the following addresses in VDR WAN and Option PC. ・...
Page 120
Chapter9 Appendix STEP 2 Set IP Address of Server PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and check that the following IP address is registered into the Server PC. ・IP Address =192.168.0.10 ・Subnet Mask =255.255.255.0 It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
Page 121
Chapter9 Appendix STEP 3 Set by the Setup software of Server PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for Server PC”, and set by the Setup software. (1) System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・...
Page 122
Chapter9 Appendix (2)Ethernet tab screen Check that the following IP address is set. ・LAN1(VDR Side)=192.168.0.251 ・VDR IF(Router) Connect=None 192.168.0.251 None (3)Set the following IP address in the Terminal block. ・Terminal1=192.168.0.11 ・Terminal2=192.168.0.12 ・Terminal3=192.168.0.13 (4)Click the [All Set] button, and setting of the Server PC is completion. VDR/S-VDR Real Time Monitor / Installation Manual...
Page 123
Chapter9 Appendix STEP 4 Set IP Address of Client PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and check that the following IP address is registered into the Client PC. ・IP Address Client1 =192.168.0.11 Client2 =192.168.0.12 Client3...
Page 124
Chapter9 Appendix STEP 5 Set by the Setup software of Client PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client PC”, and set by the Setup software. (1)System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・...
Page 125
Chapter9 Appendix (2) Ethernet tab screen There is no setup in the Ethernet tab screen. (3) Click the [All Set] button, and setting of the Client PC is completion. Please set up other Client PC similarly. VDR Real Time Monitor / Installation Manual...
Page 126
Chapter9 Appendix STEP 6 Change setup of VDR IF (Router) Change the described IP filter in the script file of VDR/S-VDR. The script file to change is "18firon.cfg." There is the script file in the VDR/S-VDR Real Time Monitor install CD-ROM. Script file VDR/S-VDR Real Time Monitor / Installation Manual...
Page 127
Chapter9 Appendix (1)Open the 18firon.cfg file by text editor (Example: Notepad), and change it. Change part is IP Address which is adding shading, and please input the IP address of Server In this example, since it is “Server PC=192.168.0.10”, it is set to source=”192.168.0.10.” # Command Handler configuration # System configuration set system name="VDR_IF"...
Page 128
Chapter9 Appendix (2) In order to send the Script file to the VDR IF, connect the VDR IF setting cable as follows. (3)Start the Hyper Terminal software, and set as follows. Please refer to “9.3 Hyper Terminal Setup” for more detail. Item Value Bits per second...
Page 129
Chapter9 Appendix (5)Delete the current script file by the “delete” command as follows. Manager vdr_if> delete file=18firon.cfg Enter (6)To send the changed script file, input the “load” command as follows. Manager vdr_if> load method=zmodem asyn=0 destination=flash Enter Router ready to begin ZMODEM file transfers . . . (7) Select menu in order of "Transfer"...
Page 130
Chapter9 Appendix (9) Close the Hyper Terminal software, and restart the VDR IF by power switch. (10) To check that the firewall became valid, input the “show” command as follows. Since the VDR IF is restarted, open the command prompt screen again and check the firewall after logging in the VDR IF.
Client PC2 (*2) NOTE 1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply 192.168.0.13 2. *2 PC : Owner supply 3. *3 JCY-1800 : EXT-LAN VDR/S-VDR JCY-1850 : JRC-LAN Real Time Monitor Client PC3 (*2) VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM...
Page 132
Chapter9 Appendix STEP 1 Set by Maintenance software (1) Open the Option PC(VDR Real Time Monitor)screen. (2) Click the [Receive] button to receive the VDR/S-VDR configuration data. (3) Click the [All Enable] button. (4) Check that the following addresses in VDR WAN and Option PC. ・...
Page 133
Chapter9 Appendix STEP 2 Set IP Address of Server PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and check that the following IP address is registered into the Server PC. ・IP Address =192.168.0.10 ・Subnet Mask =255.255.255.0 It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
Page 134
Chapter9 Appendix STEP 3 Set by the Setup software of Server PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for Server PC”, and set by the Setup software. (1) System tab screen ・ Input “✓” when monitor or record in the Audio block is needed. ・...
Page 135
Chapter9 Appendix (2)Ethernet tab screen Check that the following IP address is set. ・LAN1(VDR Side)=192.168.0.251 ・VDR IF(Router) Connect=None 192.168.0.251 None (3)Set the following IP address in the Terminal block. ・Terminal1=192.168.0.11 ・Terminal2=192.168.0.12 ・Terminal3=192.168.0.13 (4)Click the [All Set] button, and setting of the Server PC is completion. VDR Real Time Monitor / Installation Manual...
Page 136
Chapter9 Appendix STEP 4 Set IP Address of Client PC Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and check that the following IP address is registered into the Client PC. ・IP Address Client1 =192.168.0.11 Client2 =192.168.0.12 Client3...
Page 137
Chapter9 Appendix STEP 5 Set by the Setup software of Client PC Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client PC”, and set by the Setup software. (1)System tab screen ・ Input a check when monitor or record in the Audio block is needed. ・...
Page 138
Chapter9 Appendix (2) Ethernet tab screen There is no setup in the Ethernet tab screen. (3) Click the [All Set] button, and setting of the Client PC is completion. Please set up other Client PC similarly. VDR/S-VDR Real Time Monitor / Installation Manual...
Page 139
Chapter9 Appendix STEP 6 Change setup of VDR IF (Router) Change the described IP filter in the script file of VDR/S-VDR. The script file to change is "18firon.cfg." There is the script file in the VDR/S-VDR Real Time Monitor install CD-ROM. Script file VDR Real Time Monitor / Installation Manual...
Page 140
Chapter9 Appendix (1)Open the 18firon.cfg file by text editor (Example: Notepad), and change it. Change part is IP Address which is adding shading, and please input the IP address of Server In this example, since it is “Server PC=192.168.0.10”, it is set to source=”192.168.0.10.” # Command Handler configuration # System configuration set system name="VDR_IF"...
Page 141
Chapter9 Appendix (2) In order to send the Script file to the VDR IF, connect the VDR IF setting cable as follows. (3)Start the Hyper Terminal software, and set as follows. Please refer to “9.3 Hyper Terminal Setup” for more detail. Item Value Bits per second...
Page 142
Chapter9 Appendix (5)Delete the current script file by the “delete” command as follows. Manager vdr_if> delete file=18firon.cfg Enter (6)To send the changed script file, input the “load” command as follows. Manager vdr_if> load method=zmodem asyn=0 destination=flash Enter Router ready to begin ZMODEM file transfers . . . (7) Select menu in order of "Transfer"...
Page 143
Chapter9 Appendix (9) Close the Hyper Terminal software, and restart the VDR IF by power switch. (10) To check that the firewall became valid, input the “show” command as follows. Since the VDR IF is restarted, open the command prompt screen again and check the firewall after logging in the VDR IF.
Page 144
Chapter9 Appendix STEP 6 Change Radar IF setup It is necessary to change destination IP address of UDP output from the Radar IF since the Server PC IP address is changed. To change the IP address, download the IP.txt by the Internet Explorer of the Server PC, and change it.
Page 145
Chapter9 Appendix (1) Input “192.168.111.152” in the Address, and the following screen is displayed. Address IP.txt VDR Real Time Monitor / Installation Manual...
Page 146
Chapter9 Appendix (2) Click the IP.txt menu, and the content of the IP.txt is displayed. Please select “Save As” in the File menu, and save the IP.txt on the desktop. (3) Open the saved Ip.txt file by the Notepad, and set the Server PC IP address as the destination. In this example, destination IP address is 192.168.000.010.
Page 147
Chapter9 Appendix (4) To send the IP.txt file, click the IP.txt upload menu. IP.txt upload VDR Real Time Monitor / Installation Manual...
Page 148
Chapter9 Appendix (5) Click the [Browse] button, and select the changed IP.txt file. To send it, click the [Upload] button. If transfer is finished, “Ip.txt write OK”message is displayed. VDR/S-VDR Real Time Monitor / Installation Manual...
Page 149
Chapter9 Appendix (6) To restart the FGB, click the Reset menu. Reset Radar IF setup is completion above. VDR Real Time Monitor / Installation Manual...
Chapter9 Appendix 9.3 Hyper Terminal Setup 9.3.1 Starting (1) Select from a [start] button in order of "All Programs" => "Accessories" => "Communications" => "Hyper Terminal." (2) Enter a name for the connection, and click the [OK] button. Here, "VDR_IF" is inputted as an example. (3) Select a COM port which connects with the VDR IF, and click the [OK] button.
Page 151
Chapter9 Appendix (5) The Hyper Terminal screen is indicated. (6) Select the Properties in the File menu, and select the Setting tab. Set the following items. ・Backspace key sends ⇒ Delete ⇒ VT100J ・Emulation (7) Click the [Input Translation] button and click the [OK] button after the “Shift-JIS” selection. VDR Real Time Monitor / Installation Manual...
Page 152
Chapter9 Appendix 9.3.2 End (1) If still logged in to the VDR IF, please input the “logoff “ command in order to log off. Manager vdr_if > logoff (2) Click the Exit in the File menu bar. (3) When the confirmation screen is indicated, click the [Yes] button. (4) If you save the connection information, click the [Yes] button.
Page 156
For further information,contact: Not use the asbestos http://www.jrc.co.jp Marine Service Department Telephone : +81-3-3492-1305 Facsimile : +81-3-3779-1420 e-mail : tmsc@jrc.co.jp AMSTERDAM Branch Telephone : +31-20-658-0750 Facsimile : +31-20-658-0755 e-mail : service@jrcams.nl SEATTLE Branch Telephone : +1-206-654-5644 Facsimile : +1-206-654-7030 e-mail : service@jrcamerica.com...