Qy82P Transistor Output Module (Source Type) - Mitsubishi QX10 User Manual

3 OUTPUT MODULE SPECIFICATIONS

3.17 QY82P Transistor Output Module (Source Type)

Specifications
Number of output points
Isolation method
Rated load voltage
Maximum load current
Maximum inrush current
Leakage current at OFF
Maximum voltage drop at ON
OFF to ON
Response time
ON to OFF
Surge suppressor
Fuse
Voltage
External supply
power
Current
Dielectric withstand voltage
Insulation resistance
Noise immunity
Protection degree
Common terminal arrangement
Number of occupied I/O points
Protection function
Operation indicator
External connections
Applicable wire size
Applicable connector
Applicable connector/terminal
block converter module
Internal current consumption
(5VDC)
Weight
External connection
The above diagram shows the first half of 32 points (F).
The latter half of 32 points (L) are similar.
1: Pin number of 1
side connector.
2: Selection of left-hand (F) side provides the first half (Y00 to Y1F) LED indications, and selection of right-hand (L) side provides the
latter half (Y20 to Y3F) LED indications.
3: When using A6CON2 or A6CON3, refer to Chapter 7.
3 - 19
Type
0.1A/1point, Pilot Duty, 2A/common
0.1VDC (TYP.) 0.1A, 0.2VDC (MAX.) 0.1A
1ms or less (rated load, resistive load)
12-24VDC (+20/-15%) (ripple ratio within 5%)
560VAC rms/3 cycles (altitude 2000m)
10MΩ or more by insulation resistance tester
By noise simulator of 500Vp-p noise voltage, 1
First transient noise IEC61000-4-4: 1kV
32 points/common (common terminal: 1B01, 1B02, 2B01, 2B02)
64 points (I/O assignment is set as a 64-point output module.)
Yes (overheat protection function, overload protection function)
• Overheat protection function is activated in increments of 2 points.
• Overload protection function is activated in increments of 1 point.
ON indication (LED), 32 point switch-over using switch
0.088 to 0.3mm
A6CON1, A6CON2, A6CON3, A6CON4 (optional)
indicates that of the left-hand side connector, and pin number of 2
Transistor Output Module (Source Type)
QY82P
64 points
Photocoupler
12-24VDC (+20/-15%)
0.7A, 10ms or less
0.1mA or less
1ms or less
Zener diode
No
40mA (at 24VDC)/common
and 25 to 60Hz noise frequency
IP2X
40-pin connector
2
(For A6CON1 or A6CON4)
A6TBXY36, A6TBXY54
160mA (TYP. all points ON)
0.17kg
Pin-Outs
B20 A20
B19 A19
B18 A18
B17 A17
B16 A16
B15 A15
B14 A14
B13 A13
B12 A12
B11 A11
B10 A10
B9 A9
B8 A8
B7 A7
B6 A6
B5 A5
B4 A4
B3 A3
B2 A2
B1 A1
Module front
view
s noise width
3
Pin Pin Pin
Signal Signal
No. No. No.
No. No.
1 1
1B20 Y00 1A20 Y10 2B20
1B19 Y01 1A19 Y11 2B19
1B18 Y02 1A18 Y12 2B18
1B17 Y03 1A17 Y13 2B17
1B16 Y04 1A16 Y14 2B16
1B15 Y05 1A15 Y15 2B15
1B14 Y06 1A14 Y16 2B14
1B13 Y07 1A13 Y17 2B13
1B12 Y08 1A12 Y18 2B12
1B11 Y09 1A11 Y19 2B11
1B10 Y0A 1A10 Y1A 2B10
1B09 Y0B 1A09 Y1B 2B09
1B08 Y0C 1A08 Y1C 2B08
1B07 Y0D 1A07 Y1D 2B07
1B06 Y0E 1A06 Y1E 2B06
1B05 Y0F 1A05 Y1F 2B05
1B04 Vacant 1A04 Vacant 2B04 Vacant 2A04 Vacant
1B03 Vacant 1A03 Vacant 2B03 Vacant 2A03 Vacant
1B02 COM1 1A02 0V 2B02 COM2 2A02
1B01 COM1 1A01 0V 2B01 COM2 2A01
indicates that of the right-hand
MELSEC-Q
Appearance
Pin
Signal Signal
No.
No. No.
1 1
Y20 2A20 Y30
Y21 2A19 Y31
Y22 2A18 Y32
Y23 2A17 Y33
Y24 2A16 Y34
Y25 2A15 Y35
Y26 2A14 Y36
Y27 2A13 Y37
Y28 2A12 Y38
Y29 2A11 Y39
Y2A 2A10 Y3A
Y2B 2A09 Y3B
Y2C 2A08 Y3C
Y2D 2A07 Y3D
Y2E 2A06 Y3E
Y2F 2A05 Y3F
0V
0V
3 - 19