Qx40H Dc High-Speed Input Module (Positive Common Type) - Mitsubishi QX10 User Manual

2 INPUT MODULE SPECIFICATIONS

2.7 QX40H DC High-Speed Input Module (Positive Common Type)

Type
Specifications
Number of input points
Isolation method
Rated input voltage
Rated input current
Input derating
ON voltage/ON current
OFF voltage/OFF current
Input impedance
SW1 (noise filter)
1
Set value 2
Response
TYP.
time OFF to ON
MAX.
TYP.
ON to OFF
MAX.
Function
SW2 4
setting
Dielectric withstand voltage
Insulation resistance
Noise immunity 5
Protection degree
Common terminal
arrangement
Number of occupied I/O
points
Interrupt processing condition
Operation indicator
External connections
Applicable wire size
Applicable crimping terminal
Internal current consumption
(5VDC)
Weight
1: If the noise filter selector switch (switch 1) on the bottom of the module (refer to Chapter 10) is turned on, the noise filter takes effect.
The off-status noise filter disables I/O response time setting.
After switching on or off the switch 1, reset the power supply of the CPU module.
2: Set an input response time in "I/O response time" combo box of PLC parameter in GX Developer. (Default: 0.2ms)
A response time setting value can be changed in GX Developer (SW6D5C-GPPW or later).
For the setting details, refer to Section 1.3.1.
3: The actual response time is 5
For the details of the CPU overhead time, refer to manuals for the CPU module used (Function Explanation, Program Fundamentals).
4: The module function can be changed according to the status of the function selector switch (switch 2) on the bottom of the module
(refer to Chapter 10).
ON: High-speed input
OFF: Interrupt
If the function selector switch (switch 2) setting is changed while the CPU module is in RUN, an error (error code: 2100) occurs.
5: Indicates the noise immunity when the noise filter takes effect (the noise filter selector switch (switch 1) is turned on).
6: For the setting method, refer to Section 1.3.3.
2 - 7
DC high-speed input module (Positive common type)
24VDC (+20/-15%, ripple ratio within 5%)
Refer to the derating chart.
13V or higher/3mA or higher
8V or lower/1.6mA or lower
OFF
Invalid 0.1
0ms 3 0.04ms
- 3 0.05ms
0ms 3 0.04ms
- 3 0.05ms
OFF: Interrupt, ON: High-speed input
560VAC rms/3 cycles (altitude 2000m)
10MΩ or more by insulation resistance tester
By noise simulator of 500Vp-p noise voltage, 1
and 25 to 60Hz noise frequency
8 points/common (common terminal: TB9, TB18)
16 points (I/O assignment is set as a 16-point high-speed input module or 16-
point interrupt module.)
Set by Switch setting in GX Developer
18-point terminal block (M3
0.3 to 0.75mm
R1.25-3 (Sleeved crimping terminals cannot be used.)
80mA (TYP. all points ON)
s delay when turning on, 10
QX40H
16 points
Photocoupler
Approx. 6mA
Approx. 3.9kΩ
ON
0.2 0.4
0.10ms 0.25ms 0.50ms
0.15ms 0.30ms 0.60ms
0.10ms 0.25ms 0.50ms
0.15ms 0.30ms 0.60ms
IP2X
4
ON indication (LED)
6 screws)
2
core (2.8mm OD max.)
0.16kg
s delay when turning off, because the hardware response time is added.
0.6 1
0.95ms
1.00ms
0.95ms
1.00ms
s noise width
4 6
MELSEC-Q
Appearance
2 - 7