YASKAWA V1000 Technical Manual page 373

No. Name
Output Frequency after Soft
U1-16
Starter
U1-18 oPE Fault Parameter
MEMOBUS/Modbus Error
U1-19
Code
U1-24 Input Pulse Monitor
U1-25 Software No. (Flash)
U1-26 Software No. (ROM)
U1-27 Operator Message ID
U1-28 Drive Message ID
U2-01 Current Fault
U2-02 Previous Fault
Frequency Reference at
U2-03
Previous Fault
Output Frequency at
U2-04
Previous Fault
Output Current at Previous
U2-05
Fault
Motor Speed at Previous
U2-06
Fault
Output Voltage at Previous
U2-07
Fault
DC Bus Voltage at Previous
U2-08
Fault
Output Power at Previous
U2-09
Fault
Torque Reference at
U2-10
Previous Fault
Input Terminal Status at
U2-11
Previous Fault
Output Terminal Status at
U2-12
Previous Fault
Drive Operation Status at
U2-13
Previous Fault
Cumulative Operation Time
U2-14
at Previous Fault
Soft Starter Speed Reference
U2-15
at Previous Fault
Motor q-Axis Current at
U2-16
Previous Fault
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
Description
Displays output frequency with ramp time and S-curves.
Units determined by o1-03.
Displays parameter no. for oPEoo or Err where error
occurred.
Displays the contents of a MEMOBUS/Modbus error.
CRC Error
Data Length Error
Not Used
Parity Error
Overrun Error
Framing Error
Timed Out
Not Used
Displays the Pulse Train input RP frequency.
Flash ID
ROM ID
Displays the numeric code of the remote operator (for use
by the manufacturer).
Displays the numeric code of the drive (for use by the
manufacturer)
U2: Fault Trace
Use U2 monitors to view fault trace data.
Displays the current fault.
Displays the previous fault.
Displays the frequency reference at the previous fault.
Displays the output frequency at the previous fault.
Displays the output current at the previous fault.
Displays the motor speed at the previous fault.
Displays the output voltage at the previous fault.
Displays the DC bus voltage at the previous fault.
Displays the output power at the previous fault.
Displays the torque reference at the previous fault.
Displays the input terminal status at the previous fault.
Displayed as in U1-10.
Displays the output status at the previous fault. Displays
the same status displayed in U1-11.
Displays the operation status of the drive at the previous
fault. Displays the same status displayed in U1-12.
Displays the cumulative operation time at the previous
fault.
Displays the run speed after a soft start when a previous
fault occurred. Displayed as in U1-16.
Displays the q-axis current for the motor at the previous
fault.
B.2 Parameter Table
Analog Output
Unit
Level
10 V: Max 0.01
frequency Hz
No output signal
–
available
No output signal
–
available
32000 1 Hz A A A
No signal output
–
avail.
No signal output
–
avail.
No signal output
–
avail.
No signal output
–
avail.
<3>
No signal output
–
avail.
No signal output
–
avail.
No signal output 0.01
avail. Hz
No signal output 0.01
avail. Hz
<1>
No signal output
avail.
<2>
No signal output 0.01
avail. Hz
No signal output
0.1 V A A A
avail.
No signal output
1 V
avail.
No signal output 0.1
avail. kW
No signal output
0.1% − Α −
avail.
No signal output
–
avail.
No signal output
–
avail.
No signal output
–
avail.
No signal output
1 H
avail.
No signal output 0.01
avail. %
No signal output 0.10
avail. %
Control
Mode
Addr.
O
Hex
V/ P
L
f M
V
A A A 53
A A A 61
A A A 66
7D
A A A 4D
A A A 5B
A A A 7A8
A A A 7A9
A A A 80
A A A 81
A A A 82
A A A 83
A A A 84
− A − 85
86
A A A 87
A A A 88
89
A A A 8A
A A A 8B
A A A 8C
A A A 8D
B
A A A 7E0
A A A 7E1
373