YASKAWA V1000 Technical Manual page 344

B.2 Parameter Table
No. Name
Motor 2 Max
E3-04
Output Frequency
E3-05
Motor 2 Max
<1>
Voltage
Motor 2 Base
E3-06
Frequency
Motor 2 Mid Output
E3-07
Freq.
E3-08
Motor 2 Mid Output
<1>
Freq. Voltage
Motor 2 Min.
E3-09
Output Freq.
Motor 2 Min.
E3-10
Output Freq.
<1>
Voltage
E3-11
Motor 2 Mid Output
<7>
Frequency 2
E3-12
Motor 2 Mid Output
<1>
Frequency Voltage
<13> 2
E3-13
Motor 2 Base
<1>
Voltage
<9>
Motor 2 Rated
E4-01
Current
Motor 2 Rated
E4-02
Slip
Motor 2 Rated No-
E4-03
Load Current
Motor 2 Motor
E4-04
Poles
Motor 2 Line-to-
E4-05
Line Resistance
Motor 2 Leakage
E4-06
Inductance
Motor 2 Motor
Iron-Core
E4-07
Saturation
Coefficient 1
Motor 2 Motor
Iron-Core
E4-08
Saturation
Coefficient 2
Motor 2
E4-09
Mechanical Loss
E4-10 Motor 2 Iron Loss
Motor 2 Rated
E4-11
Capacity
344
Description
To set linear V/f characteristics, set the same values for
E3-07 and E3-09. In this case, the setting for E3-08 will be
disregarded.
Ensure that the five frequencies are set according to these
rules to prevent triggering an oPE10 fault:
E3-09 ≤ E3-07 < E3-06 ≤ Ε3−11 ≤ E3-04
Note: Setting E3-11 to 0 disables both E3-11 and E3-12,
and the above conditions do not apply.
VACrms Out (V)
E3-05
E3-12
E3-13
E3-08
E3-10
E3-09 E3-07
Frequency (Hz)
E4: Motor 2 Parameters
Use E4 parameters to control a second motor operating on the same drive.
Sets the motor 2 nameplate full load current in amperes
(A). This value is automatically set during Auto-Tuning.
Sets the motor 2 rated slip in Hz. Automatically set during
Auto-Tuning.
Sets the magnetizing current of motor 2 in Ampere.
Automatically set during Rotational Auto-Tuning.
Sets the number of poles of motor 2. This value is
automatically set during Auto-Tuning.
Sets the phase-to-phase resistance of motor 2 in ohms.
Automatically during Auto-Tuning.
Sets the voltage drop due to motor leakage inductance as a
percentage of rated voltage of motor 2. Automatically set
during Auto-Tuning.
Set to the motor iron saturation coefficient at 50% of
magnetic flux. Automatically set during Rotational
Auto-Tuning.
Set to the motor iron saturation coefficient at 75% of
magnetic flux. This value is automatically set during
Rotational Auto-Tuning.
Sets the motor mechanical loss as a percentage of motor
rated power (kW) capacity.
Adjust in the following circumstances:
• When there is a large amount of torque loss due to motor
bearing friction.
• When there is a large amount of torque loss.
Sets the motor iron loss in watts.
Sets the motor rated capacity in kW. Automatically set
during Auto-Tuning.
E3-06 E3-11 E3-04
10 to 200%
than E4-01
0.0 to 40.0
Setting for
E4-07 to
0 to 65535
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
Control
Mode
Range Def.
O
V/f
LV
60 Hz
40.0 to
A A
<19>
400.0
0.0 to
200.0 V A A
255.0
60 Hz
0.0 to
A A
<19>
E3-04
3.0 Hz
0.0 to
<12>
A A
E3-04
<19>
16.0 V
0.0 to
<6>
A A
255.0
<12>
1.5 Hz
0.0 to
<12>
A A
E3-04
<19>
12.0 V
0.0 to
<6>
A A
255.0
<12>
0.0 to
0.0 Hz A A
E3-04
0.0 to
255.0
0.0 Vac A A
<1>
0.0 to
255.0
0.0 Vac A S
<1>
of drive
<10>
A A
rated
current
0.00 to
<10>
A A
20.00
0 to less
<10>
A A
<9>
2 to 48 4 poles A A
0.000 to
65.000
<10>
A A
<11>
<10>
A A
0.00 to
0.50 − A
0.50
0.75 − A
0.75
0.00 to
0.0 − A
10.0
<10>
Α −
0.00 to
<6>
A A
650.00
Addr. Hex Pg.
PM
− 31A 167
− 31B 167
− 31C 167
− 31D 167
− 31E 167
− 31F 167
− 320 167
− 345 167
− 346 167
− 347 167
− 321 168
− 322 168
− 323 169
− 324 169
− 325 169
− 326 169
− 343 169
− 344 169
− 33F 169
− 340 170
− 327 170