Steam Distribution; Carel Jet Distributors (Sdpoem00**); Carel Linear Distributors For Air Ducts (Dp***Dr0); Carel Steam Blowers (Vsdu0A*, Models Ue003 To Ue015 Only) - Carel humiSteam UE005 User Manual

ENG

3.1 CAREL jet distributors (SDPOEM00**)

These can be fitted horizontally or vertically (hole facing upwards).
See page 31 for the models of distributors.
Assembly instructions (see Fig.3.a ):
•
make a series of holes on the wall according to the distributor drilling
template;
•
insert the distributor;
•
fasten the flange using 4 screws.
50
31,5
A
B
Key:
A. steam inlet
B. condensate drain
C. steam outlet.
the dimensions of the hole vary depending on the models of
distributor:
model SDPOEM0000: hole made manually, up to 30 mm (1.2") in
diameter);
model SDPOEM0012: diameter of the hole 12 mm (0.5");
model SDPOEM0022: diameter of the hole 22 mm (0.9").
D drilling template
Note: if steam hoses with an inside diameter of 30 mm (1.2") are
used, remove the 22 mm (0.9") steam inlet section.
3.2 CAREL linear distributors for air ducts
(DP***DR0)
Install away from obstacles (curves, branches, changes in cross-section,
grills, filters, fans).
Minimum distance between the distributor and the obstacle: 1/1.5 m
(3.3/4.9 ft). Increase the distance if:
•
the air speed increases in the duct,
•
the relative humidity of the air increases before and after
humidification,
•
the turbulence decreases.
See page 33 for installation examples.
Assembly instructions (see Fig.3.b ):
•
make a series of holes on the wall according to the distributor drilling
template (included in the packaging with the distributor);
•
insert the distributor with the steam hole
"UE BASIC" +08C0042EZ - rel. 1.0 - 16.10.2017

3. STEAM DISTRIBUTION

50
31,5
D
C
C
B
A
Fig. 3.a
3
4
5
X
Key:
1 "L"-shaped mounting support (where featured)
2 flange gasket
3 steam inlet (ØA)
4 condensate drain (ØB)
5 screw diameter (see the instruction sheet supplied with the distributor)
6 length (depending on the model of distributor, see par. "10.5" page 38)
7 angle (around 2°) for draining the condensate.
8 diameter of the hole on the wall (ØY)
Dimensions in mm (in)
DP***D22R0
ØA 22 (0.9")
ØB 10 (0.4")
ØY 58 (2.3")
Ø 35 (1.4")
X 68 (2.7")
Important:
1. fit the distributor at a slight incline (at least 2°, to prevent the return
of condensate);
2.
the "L"-shaped mounting support (see part 1 Fig. 3.c) is supplied with
steam distributor models from DP085* to DP025*. For shorter lengths,
the support can be supplied as an option (code 18C478A088).
3.3 CAREL steam blowers (VSDU0A*,
models UE005 to UE015 only)
Steam distributors for humidifiers with flow rates up to 15 kg/h. Can be
connected on top of the humidifier, or separately in another location (see
the figure below).
D
C
DIMENSIONS (m) A B C
>0,5 >5 ≥2,1 >1
Important: For correct distribution of the steam, observe
the distance shown in the figure above.
12
1
2
6
7
8
Y
B
Fig. 3.b
CAREL linear distributors
DP***D30R0 DP***D40R0
30 (1.18") 40 (1.57")
10 (0.4") 10 (0.4")
68 (2.7") 89 (3.5")
45 (1.8") 60 (2.4")
77 (3.0") 99 (3.9")
Tab. 3.bTab. 3.a
G
D DIMENSIONS (m) E F
>0,5 >5 >1
Fig. 3.c
di
G