Thank you for purchasing Black Horse Model products. With over 18 years experience in production and fly testing, Black Horse Model is committed to bring the best quality products and good service to customers. Along with a team of creative engineers and skilled workers, we will always accompany with customers by our great experiences, fully enthusiasm...
In that Black Horse Model has no control over the final assembly or material used for final assembly, SUGGESTION Black Horse Model is not responsible for loss of use , or other incidental or consequential damages. To avoid scratching your new airplane, do not...
SBACH 342 Item code: BH174 Instruction Manual FLIGHT WARNINGS ADHESIVES AND REQUIRED TOOLS When ready to fly, first extend the transmitter aerial. Thin CA Switch on the transmitter. 30-minute epoxy Switch on the receiver. 6-minute epoxy Check that the wings are correctly fitted to the Threadlocker thread locking cement fuselage.
Page 5
SBACH 342 Item code: BH174 Instruction Manual • Officially designated AMA Air Show Teams (AST) are authorized to use devices and practices as defined within the Team AMA Program Document. (AMA Document #718.) (j) Not operate a turbine-powered aircraft, unless in compliance with the AMA turbine regulations. (AMA Document #510-A.)
SBACH 342 Item code: BH174 Instruction Manual SUGGESTION FOR ENGINE AND SERVO PREPARATIONS Use a covering iron with a covering sock on • ENGINE: DLE 35 RA; OS 33GT high heat to tighten the covering if necessary. • SERVO: Two Options...
SBACH 342 Item code: BH174 Instruction Manual Make certain the hinges are adequately secured with glue. If they come loose in flight accidents may result. Apply epoxy glue INSTALLING THE AILERONS SERVOR 1. Install the rubber grommets and brass eyelets onto 4.
Page 10
SBACH 342 Item code: BH174 Instruction Manual < Aileron servo > Servo ARM Hitec 24T.2’’ < Bottom view > 1.5mm Warning! Set all scerws securely. If they come off during flight you will lose control of your aircraft! Must be purchased <...
SBACH 342 Item code: BH174 Instruction Manual INSTALLING THE AILERON LINKAGES 4. Center the aileron and hold it in place using a couple of pieces of masking tape. Adjust the 1. Install the control horn into the aileron. linkage until the aileron and the servo arm are both centered and then tighten the nut against.
Page 12
SBACH 342 Item code: BH174 Instruction Manual < Bottom view > Assemble left and right sides the same way Apply threadlocker (screw cement).
SBACH 342 Item code: BH174 Instruction Manual INSTALLING THE MAIN LANDING 5 x 50mm 4 x 15mm Cap Screw - - - - 2 M5 Blind Nut 4mm Washer Collar 4mm Spring Washer 85mm 5mm Washer - - - - - - - - - - - 6 3 x 10mm Button Screw <...
Page 15
SBACH 342 Item code: BH174 Instruction Manual 5x50mm Washer M5 Blind Nut Washer M5 Blind Nut Collar 85mm Wheel Main gear Wheel Pant Main gear M5 Blind Nut 5x50mm Washer Assemble left and right Collar sides the same way. Wheel...
Page 16
SBACH 342 Item code: BH174 Instruction Manual 3 x 10mm 85mm Wheel Button Screw Main gear Apply threadlocker (screw cement). Assemble left and right Wheel Pant sides the same way < Bottom view >...
SBACH 342 Item code: BH174 Instruction Manual SECURE THE WING TO THE FULSELAGE 6 x 25mm Plastic Screw Attach the wings to the fuselage and secure the wing panels. 6 x 25mm < Top view >...
SBACH 342 Item code: BH174 Instruction Manual HORIZONTAL STABILIZER INSTALLATION 1. Using a modeling knife, cut away the covering When you are sure that everything is aligned from the fuselage for the stabilizer and remove it. correctly, mix up a generous amount of 30 minute epoxy.
Page 20
SBACH 342 Item code: BH174 Instruction Manual Top view 4 x 15mm Socket Head Cap Screw Bottom view...
SBACH 342 Item code: BH174 Instruction Manual RUDDER INSTALLATION Pinned Hinge < Top view > Pinned Hinge - - - - 5 90 Degree Cut off shaded portion Apply epoxy glue 9. Attach the clevis to the rudder servo. There should be...
Page 22
SBACH 342 Item code: BH174 Instruction Manual < Bottom view > Aluminum ball 3x12mm Cable Cable rod 3x35mm 3x12mm 3.2mm Servo ARm Hitec 24T.4’’ Cut off shaded portion Must be purchased separately! Pay close attention here...
SBACH 342 Item code: BH174 Instruction Manual Rudder servo INSTALLING THE ELEVATOR SERVO INSTALLING THE ELEVATOR LINKAGES 1. Remove the covering from both size of the Repeat these step as installing the aileron linkages. fuselage. 2. Install two servo to the fuselage as shown.
Page 24
SBACH 342 Item code: BH174 Instruction Manual < Bottom view > 3x12mm Elevator rod Servo ARm 3x12mm Must be purchased Hitec 24T.2’’ separately! Apply threadlocker Assemble left and right Pay close attention here (screw cement). sides the same way...
SBACH 342 Item code: BH174 Instruction Manual Assemble left and right sides the same way INSTALLING THE TAIL WHEEL 3 x 15mm Cap Screw #2-Tail wheel set 3 x 15mm < Bottom view > 3 x 15mm TP Screw 3mm Spring Washer...
SBACH 342 Item code: BH174 Instruction Manual INSTALLING THE ENGINE May be you also need to trim some wood from the tri-angle Using plate of plywood (supplied with the kit) mark the holes wood for the installation is easy. onto the fire wall for installing the engine mount for DLE-35CC or OS-33CC.
Page 29
SBACH 342 Item code: BH174 Instruction Manual 5mm Flat Washer 16 x 5mm Flat Washer 5 x 100mm Cap Screw - - - - - - - - - - - 4 5mm Spring Washer 16 x 5mm Rubber Washer...
Page 30
SBACH 342 Item code: BH174 Instruction Manual DLE 35 CC Electronic Ignition System Foam Zip tie DLE 35 CC Must be purchased separately!
SBACH 342 Item code: BH174 Instruction Manual Cut off shaded portion INSTALLING THE FUEL TANK 5. When satisfied with the alignment of the stopper assembly tighten the 3mm x 20mm machine screw until the rubber stopper expands and 1. Using a modeling knife, cut one length of silicon seals the tank opening.
SBACH 342 Item code: BH174 Instruction Manual Clunks #6 Fuel Tank Fuel Tank Silicone Tube Zip tie Foam ring INSTALLING THE THROTTLE 1. Plug the throttle servo into the receiver and turn on Connector the radio system. Check to ensure that the throttle servo output shaft is moving in the correct direction.
SBACH 342 Item code: BH174 Instruction Manual 1.5mm Throttle Servo Must be purchased Apply epoxy glue. separately! MOUNTING THE COWL 4. While holding the cowl firmly in position, drill 1. Remove the muffler and needle valve assembly four 1,6mm pilot holes through both the cowl from the engine.
Page 35
SBACH 342 Item code: BH174 Instruction Manual 3 x 12mm TP Screw Cut off shaded portion...
Page 36
SBACH 342 Item code: BH174 Instruction Manual C . A 3x12mm Tp Screw C . A 3x12mm Tp Screw Drill holes using the stated. Apply instant glue (C.A glue, super glue). (in this case 1.5mm 1.5mm C . A...
SBACH 342 Item code: BH174 Instruction Manual INSTALLING THE SPINNER Install the spinner back-plate, propeller and spinner cone. The propeller should not touch any part of the spinner cone. If it dose, use a sharp modeling knife and carefully trim away the spinner cone where the propeller comes in contact with it.
SBACH 342 Item code: BH174 Instruction Manual INSTALLING THE SWITCH INSTALLING THE RECEIVER AND BATTERY 1. Plug the servo leads and the switch lead into the 1. The switch should be mounted on the fuselage receiver. You may want to plug an aileron...
Page 40
SBACH 342 Item code: BH174 Instruction Manual 10 x 40mm 4 mm Spring Washer 4mm Washer 4 x 60mm M5 Blind Nut 16 x 5mm Rubber Washer 16 x 5mm Flat Washer 5 mm Spring Washer 12 x 70mm 5mm Washer...
Page 41
SBACH 342 Item code: BH174 Instruction Manual Battery Cord When rotating clock wise, change the connection of 2 wires. Must be purchased separately!
SBACH 342 Item code: BH174 Instruction Manual INSTALLING CANOPY FUSELAGE Position the canopy so the rear frame on the canopy is aligned with the rear edge of the cockpit opening. Use canopy glue to secure the canopy to the canopy hatch. Use low-tack tape to hold the canopy in position until the glue fully cures.
SBACH 342 Item code: BH174 Instruction Manual Adhesive tape. LATERAL BALANCE BALANCING 1. It is critical that your airplane be balanced correctly. After you have balanced a plane on the C.G. Improper balance will cause your plane to lose You should laterally balance it. Doing this will control and crash.
Page 44
SBACH 342 Item code: BH174 Instruction Manual 6 x 25mm Plastic Screw Plate of plywood 160-165 mm (6.3-6.5 in) Plate of plywood Pay close attention here Cut off excess. Apply instant glue Assemble left and right (CA glue, super glue).
SBACH 342 Item code: BH174 Instruction Manual In order to obtain the CG specified, reposition the receiver and other equipment. If not obtain the CG specified, add a weight and Do not fly before confirming the adjust. correct location of the CG. If the...
SBACH 342 Item code: BH174 Instruction Manual DECORATION 12mm 12mm Aileron Control < Side view > Left 11mm 11mm Elevator Control < Side view > Left 35mm 35mm Rudder Control FOR YOUR RADIO INSTALLATION BASIC CONNECTION FOR AIRPLANE AND ADJUSTMENT OF SERVOS Example of connection For more information, refer to radio system instruction manual.
SBACH 342 Item code: BH174 Instruction Manual DECORATION < Bottom view > < Top view > < Side view > Left < Side view > Right ORACCOVER #21-071 - Black #21-023 - Ferri Red #21-010 - White...
Page 50
I/C FLYING WARNINGS Always operate in open areas, away from NEVER fly near power lines,aerials or AL WAYS adjust the engine from behind factories, hospitals, schools, buildings other dangerous areas including airports, the propeller, and do not allow any part of and houses etc.
Page 51
I/C FLYING GUIDELINES Operate the control sticks on the ALWAYS land the model INTO When ready to fly, first extend transmitter and check that the the wind, this ensures that the the transmitter aerial. control surfaces move freely and in model lands at the slowest possible the CORRECT directions.