Specifications; Ec Declaration Of Conformity - Makita TM3000C Instruction Manual

SPECIFICATIONS

Oscillation per minute
Oscillation angle, left/right
Overall length
EPTA-Procedure 01/2014, are shown in the table.
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
DOUBLE INSULATION
Wear safety glasses.
Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of the European Directive,
on Waste Electric and Electronic
Equipment and its implementation in
accordance with national law, electric
equipment that have reached the end of
their life must be collected separately and
returned to an environmentally compatible
recycling facility.
Intended use
The tool is intended for sawing and cutting wood,
plastic, gypsum, non-ferrous metals, and fastening
elements (e. g. unhardened nails and staples). It is also
intended for working soft wall tiles, as well as dry sand-
ing and scraping of small surfaces. It is especially for
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841:
Work mode: Sanding
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Work mode: Cutting with plunge cut saw blade
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model
Net weight
Safety class
) : 74 dB (A)
pA
) : 78 dB (A)
pA
6,000 - 20,000 (min
Work mode: Cutting with segmental saw blade
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Work mode: Scraping
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841:
Work mode: Sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: Cutting with plunge cut saw blade
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: Cutting with segmental saw blade
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: Scraping
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration emission value may
also be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared emission
value depending on the ways in which the tool is used.
WARNING:
Be sure to identify safety measures to pro-
tect the operator that are based on an estimation of exposure
in the actual conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
2 ENGLISH
TM3000C
-1
)
1.6 ° (3.2 ° total)
275 mm
1.4 - 1.5 kg
/II
) : 76 dB (A)
pA
) : 77 dB (A)
pA
2
) : 2.5 m/s or less
h
2
2
) : 6.5 m/s
h
2
2
) : 3.0 m/s
h
2
2
) : 5.5 m/s
h
2