Specifications - Makita DTM40 Instruction Manual

ENGLISH
(Original instructions)
1 Button
2 Red indicator
3 Battery cartridge
4 Star marking
5 Indicator lamps
6 Check button
7 Slide switch
8 Dial
9 Front lamp

SPECIFICATIONS

Oscillation per minute
Oscillation angle, left/right
Overall length
Net weight
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heaviest
combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of resi-
dence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for sawing and cutting wood, plastic,
gypsum, non-ferrous metals, and fastening elements (e.
g. unhardened nails and staples). It is also intended for
working soft wall tiles, as well as dry sanding and scrap-
ing of small surfaces. It is especially for working close to
edge and flush cutting.
General Power Tool Safety Warnings
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future ref-
erence.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Explanation of general view
10 Indication lamp
11 Application tool installation bolt
12 Holes in the application tool
13 Protrusions of the tool flange
14 Hex wrench
15 Tighten
16 Adapter (required for some
application tools)
17 Nozzle band
Model
D.C. 14.4 V Model
D.C. 18 V Model
DTM40
1.7 – 2.0 kg
D.C. 14.4 V
BL1415N / BL1430B / BL1440 / BL1460B
BL1815N / BL1820B / BL1830B / BL1840B / BL1850B /
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE /
DC18SF / DC18SH / DC18WC
ENE080-1
CORDLESS MULTI TOOL SAFETY WARNINGS
1. This power tool is intended to function for saw-
ing, cutting, grinding and sanding. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
GEA010-2
2. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
3. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
4. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
18 Dust nozzle
19 Dust attachment
20 Felt ring (ø 37 mm)
21 Pad (with OIS marking)
22 Holes in the tool
23 Protrusions on the nozzle band
24 Spacer
25 Felt ring (ø 47 mm)
26 Pad (with STARLOCK marking)
DTM50
–1
6,000 – 20,000 (min )
1.6° (3.2° total)
307 – 324 mm
1.8 – 2.2 kg
D.C. 18 V
BL1860B
GEB094-2
5