Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Avigilon 1.3C-H4SL-D1
Summary of Contents for Avigilon 1.3C-H4SL-D1
-
Page 2: Fcc Notice
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications made to this equipment not expressly approved by Avigilon Corporation or parties authorized by Avigilon Corporation could void the user’s authority to operate this equipment. -
Page 3: Legal Notices
The absence of the symbols ™ and ® in proximity to each trademark in this document is not a disclaimer of ownership of the related trademark. Avigilon Corporation protects its innovations with patents issued in the United States of America and other jurisdictions worldwide: http://www.avigilon.com/patents. -
Page 4: Table Of Contents
Table of Contents Overview Cover View NPT Adapter View Pendant Wall Mount Bracket View Pendant Wall Mount View Camera Base Bottom View Camera Base Front View Camera Base Rear View Installation Required Tools and Materials Package Content Installation Steps Removing the Dome Cover Inserting Cables through the Sealing Grommet Mounting the Dome Camera to a Pipe (Optional) Mounting the Dome Camera to the Pendant Wall Mount... -
Page 5: Overview
Overview Cover View 1. NPT adapter Used to mount the dome camera to NPT pipes. 2. Pendant wall mount (optional) Used with the NPT adapter to mount the dome camera to a wall in pendant installations. 3. Tamper resistant screws Torx captive screws to fix the dome cover to the base. -
Page 6: Npt Adapter View
NPT Adapter View 1. Camera housing clips Snaps to hold camera module during installation. 2. Lanyard Connects to the lanyard anchor on the dome camera base. 3. 1-1/2” NPT thread mount Standard male 1-1/2” NPT thread mount for mounting the dome camera to a pole or bracket. NPT Adapter View... -
Page 7: Pendant Wall Mount Bracket View
Pendant Wall Mount Bracket View 1. Bracket mounting holes Points for mounting the pendant wall mount bracket to a mounting surface. 2. Mounting tabs Tabs for placing the pendant wall mount onto the bracket. 3. Mounting points Points for securing the pendant wall mount to the mounting bracket. Pendant Wall Mount Bracket View... -
Page 8: Pendant Wall Mount View
Pendant Wall Mount View 1. 1-1/2” NPS thread mount Female NPS thread mount for pendant camera installations. 2. Pendant wall mount screws Screws for securing the pendant wall mount to the mounting bracket. 3. NPT pipe entry hole A 3/4” NPT threaded hole for NPT pipe conduits. Pendant Wall Mount View... -
Page 9: Camera Base Bottom View
Camera Base Bottom View 1. Cable entry hole An entry hole for the cables required for camera operation. 2. Lanyard anchor The safety lanyard attaches to the anchor to prevent the camera from falling during installation. 3. Vent Vent to allow moisture vapor to escape the sealed housing and equalize pressure. Only available on H4SL-DO models. -
Page 10: Camera Base Front View
Camera Base Front View 1. IR illuminator Provides scene illumination in the IR spectrum. Only available on -IR models. 2. Ethernet port Accepts power and Ethernet connection to the network. The camera can only be powered by Power over Ethernet (PoE). Server communication and image data transmission also occur over this connection. -
Page 11: Camera Base Rear View
Provides a locking mechanism for the image pan adjustment 4. Micro USB port Accepts a micro USB to USB adapter. Only required when using the Avigilon USB Wi-Fi Adapter. 5. Serial number tag Device information, product serial number and part number label. -
Page 12: Installation
No. 2 Phillips screwdriver — for attaching the pendant wall mount bracket to the mounting surface. Package Content Ensure the dome camera package contains the following: Avigilon H4 SL Dome Camera (Indoor model — H4SL-D) Provided accessories that are not required for this installation: Mounting template sticker... -
Page 13: Installation Steps
4 screws (#8 x 1.25) RJ-45 grommet piercing cap Teflon sealing tape Installation Steps Complete the following steps to install the camera: Removing the Dome Cover Inserting Cables through the Sealing Grommet Mounting the Dome Camera to a Pipe (Optional) Mounting the Dome Camera to the Pendant Wall Mount Installing the Camera Base to the Mounting Adapter (Optional) Using the USB Wi-Fi Adapter Assigning an IP Address... -
Page 14: Inserting Cables Through The Sealing Grommet
Inserting Cables through the Sealing Grommet Always use the provided sealing grommet to prevent dust and debris from entering the camera. 1. Remove the sealing grommet from the camera base. 2. Push the Ethernet cable through the grommet. If you are installing the indoor model (H4SL-D), you should be able to simply push the cable, crimped or uncrimped, through the grommet by hand. -
Page 15: Mounting The Dome Camera To A Pipe
connector then push the cable through the grommet. Ensure that the orientation of the cable and grommet matches the one shown in the image. Mounting the Dome Camera to a Pipe If the dome camera needs to be installed to a pipe for a pendant installation, you can discard the surface mount adapter that is provided with the dome camera and use the NPT adapter. -
Page 16: (Optional) Mounting The Dome Camera To The Pendant Wall Mount
(Optional) Mounting the Dome Camera to the Pendant Wall Mount If the dome camera will be using the pendant wall mount, you will need to install the NPT adapter as well. 1. Determine where the cable will enter the pendant wall mount. If the cable will be pulled from inside the mounting surface, use the cable entry hole at the rear of the pendant wall mount. - Page 17 3. Fasten the pendant wall mount bracket to the mounting surface. 4. Insert the pendant wall mount over the bracket mounting tabs. 5. Pull the required cables through the preferred cable entry hole on the pendant wall mount: If you are using the pipe entry hole, pull the cables through the pipe conduit then the wall mount. Next, apply thread seal tape to the pipe conduit and screw it into the pipe entry hole.
- Page 18 6. Tighten the wall mount screws to secure the wall mount to the bracket. Use the T20 Torx key provided in the camera package. 7. Loosely thread the lock nut onto the NPT adapter, then secure the NPT adapter into the pendant wall mount.
-
Page 19: Installing The Camera Base To The Mounting Adapter
8. Carefully tighten the lock nut until the NPT adapter is secured to the wall mount. Installing the Camera Base to the Mounting Adapter After you install the mounting adapter, mount the camera base to the adapter. 1. Attach the lanyard on the mounting adapter to the anchor on the camera base. 2. -
Page 20: (Optional) Using The Usb Wi-Fi Adapter
For more information about configuring the camera from the mobile web interface see Avigilon USB Wi-Fi Adapter System User Guide. NOTE: The camera will reserve the 10.11.22.32/28 subnet for internal use while the USB Wi-Fi Adapter is plugged in. -
Page 21: Aiming The Dome Camera
The mobile web interface using the USB Wifi Adapter. For more information, see (Optional) Using the USB Wi-Fi Adapter on the previous page. Web browser interface: http://< camera IP address>/. Network Video Management software application (for example, the Avigilon Control Center software). NOTE: The default camera username is administrator with no password. Aiming the Dome Camera Reference the camera's live stream as you aim the camera. -
Page 22: (Optional) Configuring Microsd Card Storage
4. Rotate the azimuth control ring to set the image to the correct angle. 5. In the camera web browser interface or the Avigilon Control Center software, adjust the camera’s Image and Display settings. (Optional) Configuring microSD Card Storage To use the camera's SD card storage feature, you must insert an microSD card into the card slot. -
Page 23: Installing The Dome Cover
For more information, see the Avigilon Camera Configuration Tool User Guide. If the camera is connected to the Avigilon Control Center system, you can use the client software to configure the camera. For more information, see the Avigilon Control Center Client User Guide. -
Page 24: For More Information
Additional information about setting up and using the device is available in the following guides: Avigilon Control Center Client User Guide Avigilon High Definition H.264 Web Interface User Guide Avigilon Camera Configuration Tool User Guide The manuals are available on the Avigilon website: http://www.avigilon.com/support-and-downloads. For More Information... -
Page 25: Led Indicators
LED Indicators Once connected to the network, the Connection Status LED will display the progress in connecting to the Network Video Management software. The following table describes what the LEDs indicate: Connection Status Connection State Description One short flash every Obtaining IP Address Attempting to obtain an IP address. -
Page 26: Removing The Dome Camera From The Mounting Adapter
Removing the Dome Camera from the Mounting Adapter 1. Loosen the Torx screws and remove the dome cover. 2. Locate the small orange arrows that point at the camera housing clips. 3. Insert a flat head screwdriver or grommet piercing cap against one of the camera housing clips. 4. -
Page 27: Resetting To Factory Default Settings
Resetting to Factory Default Settings If the camera no longer functions as expected, you can choose to reset the camera to its factory default settings. Use the firmware revert button to reset the camera. The firmware revert button is shown in the following diagram: 1. -
Page 28: Setting The Ip Address Using The Arp/Ping Method
NOTE: The ARP/Ping Method will not work if the Disable setting static IP address through ARP/Ping method check box is selected in the camera's web browser interface. For more information, see the Avigilon™ High Definition H.264 Web Interface User Guide. -
Page 29: Specifications
Specifications Camera Lens 3-9 mm, motorized, varifocal USB Port USB 2.0 microSD/microSDHC/microSDXC slot – minimum class 6; class 10/UHS-1 or better SD Storage recommended Network Network 100Base-TX Cabling Type CAT5 Connector RJ-45 ONVIF® compliance version 1.02, 2.00, Profile S (www.onvif.org) Device Management SNMP v2c Protocols SNMP v3... - Page 30 Electrical H4SL-D — 4 W max Power Consumption H4SL-DO — 7 W max Power Source PoE: IEEE802.3af Class 3 compliant RTC Backup Battery 3V manganese lithium Environmental H4SL-D — 0 °C to 55 °C (32 °F to 131 °F) Operating Temperature H4SL-DO —...
-
Page 31: Limited Warranty And Technical Support
Limited Warranty and Technical Support Avigilon warrants to the original consumer purchaser that this product will be free of defects in material and workmanship for a period of 3 years from date of purchase. The manufacturer’s liability hereunder is limited to replacement of the product, repair of the product or replacement of the product with repaired product at the discretion of the manufacturer.