Related Manuals for Optimum B16 H Vario
Summary of Contents for Optimum B16 H Vario
- Page 1 M A S C H I N E N - G E R M A N Y Operating Manual Version 1.0.2 Bench drilling machine B16 H Vario Keep for future reference! 21 / 10 / 2008 Bench drill B16 H Vario ; Version 1.0.2 Page 1...
-
Page 2: Table Of Contents
Mounting the drilling machine table ............. 18 3.4.3 Mounting the drill head ................19 Installation ........................19 3.5.1 Fixing ......................19 First use ........................20 4 Operation Safety ......................... 21 Page 2 Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... - Page 3 There- fore, no claims may be derived from the indications and descriptions. Errors excepted! 21 / 10 / 2008 Bench drill B16 H Vario ; Version 1.0.2 Page 3...
-
Page 4: Safety
Risk: A danger that might cause serious injury or death WARNING! to a person. Danger or unsafe procedure that might cause injury to CAUTION! people or damage to property. Page 4 Safety Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 5: Further Ideograms
Pull the main plug! Use safety Use ear Use protective forbidden! glasses! protection! gloves! Use protective Wear a safety suit! Protect the Contact address boots! environment! 21 / 10 / 2008 Safety Bench drill B16 H Vario ; Version 1.0.2 Page 5... -
Page 6: Proper Use
If the bench drill is used in any way other than prescribed above, modified without authorization of Optimum Maschinen Germany GmbH, then the bench drill is being used improperly. We do not take liability for damage caused through improper use. -
Page 7: Qualification Of Employees
/ instructions by means of a signature, check if the staff is aware of safety rules and dangers in the workplace so that they observe the operating manual. 21 / 10 / 2008 Safety Bench drill B16 H Vario ; Version 1.0.2 Page 7... -
Page 8: Safety Devices
EMERGENCY-STOP switch, a drilling machine table with T-grooves to fasten the workpiece or a vice, a protective cover for the pulleys with positioning switch. Page 8 Safety Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 9: Safety Check
V-belts drill chuck protection The bench drill must only switch on when the drill chuck protection is closed. Date: Inspector (signature): 21 / 10 / 2008 Safety Bench drill B16 H Vario ; Version 1.0.2 Page 9... -
Page 10: Emergency-Stop-Button
INFORMATION YOU CANNOT START THE MACHINE IF THE PROTEC- TIVE COVER IS NOT CLOSED. Img.1-3: Protective cover Page 10 Safety Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 11: Drill Chuck Protection
Use protective gloves when lifting or handling pieces with sharp edges. Wear safety shoes when fitting, dismantling or transporting heavy components. 21 / 10 / 2008 Safety Bench drill B16 H Vario ; Version 1.0.2 Page 11... -
Page 12: Safety During Operation
All machine components and hazardous voltages are disconnected. Only the points marked with this pictogram are not included. Page 12 Safety Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 13: Use Of Lifting Equipments
Check if they are working properly! 1.15 Accident report Inform your superiors and Optimum Maschinen Germany GmbH immediately in case of acci- dents, possible sources of danger and any action which almost lead to an accident "Near misses". "Near misses" may have many possible causes. -
Page 14: Technical Data
B16 H Vario height [mm] 1500 depth [mm 1200 width [mm 1000 Speeds B16 H Vario spindle speeds [min 95 - 7500 number of stages Page 14 Technical Data Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 15: Environmental Conditions
Please note that the duration of the acoustic noise expose, the kind and nature of the working area as well as other machines may influence the noise level in the workplace. 21 / 10 / 2008 Technical Data Bench drill B16 H Vario ; Version 1.0.2 Page 15... -
Page 16: Dimensions
M A S C H I N E N - G E R M A N Y 2.10 Dimensions Img.2-1: B16 H Vario Page 16 Technical Data Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 17: Assembly 3.1 Delivery Volume
Store packed or unpacked parts only under the following ambient conditions. „Environmental conditions“ on page 15 Consult Optimum Maschinen Germany GmbH if the bench drill and accessories have to be stored for a period of over three months or under different external conditions than those given here. -
Page 18: Mounting The Drilling Machine Table
Clamp the drilling machine table on the tri- Clamping lever pod using the clamping lever. Drilling machine table Tripod Img.3-2: Assembly drilling machine table Page 18 Assembly Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 19: Mounting The Drill Head
If the setscrews are too tight and the base is uneven, the stand of the bench drill may break. 21 / 10 / 2008 Assembly Bench drill B16 H Vario ; Version 1.0.2 Page 19... -
Page 20: First Use
Check the fuse protection (fuse) of your electrical supply according to the technical specifica- tions for the total connected load of the bench drill. Page 20 Assembly Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 21: Operation
EMERGENCY-STOP drill chuck drill chuck protection drilling table Abb.4-1: B16 H Vario 21 / 10 / 2008 Operation Bench drill B16 H Vario ; Version 1.0.2 Page 21... -
Page 22: Control Panel
The push button „OFF“ switches off the rotation of the drilling spindle. Main switch Interrupts or connects the power supply. Switching on the machine Switch on the main switch. Press the hand-actuated auxiliary switch „ON“. Page 22 Operation Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 23: Switching Off The Machine
Put the V-belt on the required gear level. TENSIONED RELEASED Fig.4-3: Lever V-belt tension Retighten the clamping lever and this way tense the belt drive. 21 / 10 / 2008 Operation Bench drill B16 H Vario ; Version 1.0.2 Page 23... -
Page 24: Speed Table
CAUTION! Fasten the drilling machine Clamping screw table before releasing the clamping screw. Drilling machine table Fig.4-6: Table height adjustment Page 24 Operation Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 25: Disassembly, Assembly Of Drill Chucks And Drills
(No. 2) quick action drill chuck tool (drill) Img.4-8: drill chuck ATTENTION! Make sure that the chucked tool is positioned firmly and correctly. 21 / 10 / 2008 Operation Bench drill B16 H Vario ; Version 1.0.2 Page 25... -
Page 26: Cooling
When working with wood, make sure to use an adequate dust extraction unit, as sawdust can constitute a health hazard. Also use a suitable protective mask for any work that generates dust. Page 26 Operation Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 27: During The Working Process
In the case of deep drilling, remove the bit from time to time to remove drilling chips from the bore hole. A few drops of oil will reduce friction and prolong the service life of the bit. 21 / 10 / 2008 Operation Bench drill B16 H Vario ; Version 1.0.2 Page 27... -
Page 28: Determining The Cutting Speed And The Speed
OPTIMUM Determining the cutting speed and the speed M A S C H I N E N - G E R M A N Y Determining the cutting speed and the speed Table cutting speeds / infeed Material table Recommended infeed f... - Page 29 OPTIMUM Determining the cutting speed and the speed M A S C H I N E N - G E R M A N Y in m/min Drill bit Ø Speed n in rpm in mm 1062 1274 1415 1769...
-
Page 30: Examples To Calculatory Determine The Required Speed For Your Drilling Machine
OPTIMUM Determining the cutting speed and the speed M A S C H I N E N - G E R M A N Y in m/min Drill bit Ø Speed n in rpm in mm 39,0 40,0 41,0 42,0... -
Page 31: Maintenance
• long service life of the machine and • the quality of the products you manufacture. Installation and equipment from other manufacturers must be in optimum condition. ENVIRONMENTAL PROTECTION During work on the bit-holder head, make sure that • collector vessels are used, with sufficient capacity for the amount of liquid to be col- lected. -
Page 32: Safety
For this reason, all the intervals are only valid for the authorised conditions Interval Where? What? How? start of shift Examination for outside damages. after each „Safety check“ on page 9 maintenance or repair operation Page 32 Maintenance Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... - Page 33 V-belt Img.6-3: V-belt housing Check the electrical equipment / parts of the drilling every six machine. months „Qualification of employees“ on page 7 21 / 10 / 2008 Maintenance Bench drill B16 H Vario ; Version 1.0.2 Page 33...
-
Page 34: Repair
The spindle bearing arrangement is prelubricated. It is not required to relubricate it. Repair For any repair work, request the assistance of an employee of Optimum Maschinen Germany GmbH’s technical service or send us the machine. If the repairs are carried out by qualified technical staff, they must follow the indications given in this manual. -
Page 35: Ersatzteile - Spare Parts
OPTIMUM Ersatzteile - Spare parts M A S C H I N E N - G E R M A N Y Ersatzteile - Spare parts Ersatzteilzeichnung - Explosion drawing 7.1.1 Bohrkopf - Drilling head Abb.7-1: Bohrkopf - Drilling head 7.1.2... -
Page 36: Säule Und Bohrtisch - Column And Drilling Table
OPTIMUM Ersatzteile - Spare parts M A S C H I N E N - G E R M A N Y 7.1.3 Säule und Bohrtisch - Column and drilling table Abb.7-3: Säule und Bohrtisch - Column and drilling table 7.1.4... - Page 37 OPTIMUM Ersatzteile - Spare parts M A S C H I N E N - G E R M A N Y B16H Vario Menge Grösse Artikelnummer Bezeichnung Designation Qty. Size Item no. Schild „Spannen“ „Lösen“ Label „spans“ „release“ 0302021830...
- Page 38 OPTIMUM Ersatzteile - Spare parts M A S C H I N E N - G E R M A N Y B16H Vario Menge Grösse Artikelnummer Bezeichnung Designation Qty. Size Item no. Scheibe Washer GB 97.1-85 - 4 Innensechskantschraube...
-
Page 39: Schaltplan - Wiring Diagram
OPTIMUM Ersatzteile - Spare parts M A S C H I N E N - G E R M A N Y 7.1.5 Schaltplan - Wiring diagram 21.10.08 X:\Betriebsanleitungen\drilling_machines\B16H_Vario\B16HVario_parts\B16HVario_parts.fm... -
Page 40: Malfunctions
Locking bolt inserted • Pull out the locking bolt • Drill depth adjustment no • Release drill depth adjustment drilling spindle sleeve released downwards. Page 40 Malfunctions Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... - Page 41 Chuck loose using the adjusting screw • Tool blunt • Check, re-tighten • Piece loose • Sharpen or replace tool • Secure the piece properly 21 / 10 / 2008 Malfunctions Bench drill B16 H Vario ; Version 1.0.2 Page 41...
-
Page 42: Appendix 9.1 Copyright
Page 42 Appendix Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 43: Liability Claims For Defects / Warranty
V-belts, ball bearings, illuminants, filters, sealings, etc. Non reproducible software errors Any services which OPTIMUM GmbH or one of its agents performs in order to fulfill in the frame of an additional guarantee are neither an acceptance of the defects nor an accept- ance of its obligation to compensate. -
Page 44: Rohs , 2002/95/Ce
Optimum Maschinen Germany GmbH Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt Fax: +49 (0) 951 - 96822 - 22 E-Mail: info@optimum-maschinen.de Page 44 Appendix Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008... -
Page 45: Ec - Declaration Of Conformity
OPTIMUM M A S C H I N E N - G E R M A N Y EC - Declaration of Conformity The manufacturer/ Optimum Maschinen Germany GmbH Dr.-Robert-Pfleger-Str. 26 retailer: D - 96103 Hallstadt hereby declares that the following product... - Page 46 Speed table B16 H Vario ........24 Spindle holding fixture ......14 Table cutting speeds / infeed ....28 Technical data ......... 14 Transport ..........17 Page 46 Bench drill B16 H Vario ; Version 1.0.2 21 / 10 / 2008...