Table of contents Tools needed page Parts involved page Contents of the Danalock box page 1. Remove the old cylinder page 2. Pull out the old cylinder page 3. Adjust the new cylinder page 4. Unscrew the small screws page 5.
Page 4
13. Fit the tailpiece page 14. Align the plate marks page 15. Fasten the Danalock page 16. Activate batteries page 17. Before downloading the Danalock app page 18. Download the Danalock app page 19. Dismount instructions page 20. LED-Signals page 21.
Tools needed: To mount the Danalock you need a Philips screwdriver and two pliers or a wire cutter. Parts involved: Mortise plat e Cylinder Lock screw Rosette plate Page 5...
1. Remove the old cylinder First you have to remove your current cylinder. Unscrew the lock-screw in the mortise-plate on the side of the door. Page 7...
3. Adjust the new cylinder Measure the back part (on the outside of your door) of the old cylinder from the middle of the screwhole and away (see illustration). In the Danalock box you’ll find an adjustable lock cylinder. Back part...
4. Unscrew the small screws on both sides of the cylinder and pull it apart. Page 10...
Page 11
5. Insert the same size of spacer piece and brass tube to make the adjustable cylinder match the old cylinder. Please look at the size guide on the next pages to find the right length for the spacer piece and the brass tube. Page 11...
Size guide - When you adjust the size of the Danalock cylinder to the old cylinder you’ll have to exchange the brass tube in the center with another that fits the spacer piece. Here are the different combinations: Fits min. 35 mm...
Page 13
Size guide - last part Fits min. 50 mm 15 space piece Fits min. 55 mm 22 space piece Fits min. 60 mm 25 space piece Page 13...
7. Insert the adjustable cylinder Insert the new cylinder, and re-insert the lock-screw in the mortise-plate to fix the cylinder. (b) Do not tighten the screw to hard - make sure the cylinder is working by locking and unlocking with your hand. Page 15...
8. The right rosette spacer To avoid pulling the cylinder out of place you need to find the right spacer or a spacer combination between the rosette and the back plate. Unscrew the two breakable screws that holds the spacers together with the adjustable cylinder.
IMPORTANT! Avoid pulling the cylinder out of place. It is important that the spacer flushes or sticks out from the hole in the rosette plate. Page 17...
9. Break the screws to the right length Depending on which spacer or spacer combination you chose, it is now important that the screws that fasten the cylinder to the backplate have the right length. Use this chart to find the right length: 30 mm No spacers cut 30 mm...
IMPORTANT! Check that the lock still works! Make sure that the lock still works properly by turning the tailpiece. If you can’t lock and unlock this way please loosen the cylinder screws. (b) Page 20...
11. Give the tailpiece the right length To avoid damaging the Danalock you will have to shorten the new cylinder tailpiece to max. 35 mm from the door sur- face. Use two pliers or a wire cutter to shorten the tailpiece.
12. Attach the tailpiece adaptor Insert the green tailpiece adaptor in the center tube on the backside of the Danalock. Press on the adaptor until a click ensures it is fixed firmly to the Danalock. Page 22...
13. Fit the tailpiece to the middle of the housing base Fit the Danalock over the back plate. Make sure the tailpiece hits the slide in the middle of the adaptor. Page 23...
14. Align the plate marks Find the small marking on the edge of the backplate and align the mark on the back of the Danalock baseplate with it. Now you are sure to hit the notches on the backplate with the Danalock.
15. Fasten the Danalock Turn the Danalock clockwise until it clicks to fasten it to the back plate. NOTE: If you need to unfasten and retry, see “Uninstall instructions” at the end of the manual. Page 25...
16. Activate batteries Pull out the plastic tab to activate the batteries. A light will flash to confirm the Danalock is ready. Note: If the batteries are disconnected, you will have to re-calibrate the Danalock. Page 26...
17. Before downloading the Danalock app Your Danalock is now attached to the door. Download and open the Danalock app to finish setting it up. Leave the door open, so the lock isn’t influenced when calibrated. Page 27...
18. Download the Danalock App Go to Google Play or App Store and download the Danalock App. When the App is installed you create a user profile by pressing the blue ring. You will use this profile each time you sign into the App.
19. Dismount instructions If you need to dismount the Danalock from your door, insert a pen tip into the hole at the top inner edge of the lock and press while turning the lock counter-clockwise until the lock releases. This will not reset the...
20. LED-Signals A LED light on the Danalock indicates the status of several operations with different colours: LED-Mode LED colour Status indication Constant red till light finishes Lock has successfully locked Constant green till light finishes Lock has successfully unlocked Constant white for 3 seconds Power on.
Danalock into locked position and click once. White Auto calibration Turn the Danalock manually until the door is unlocked and leave the door open while calibrating. Lift the handle if needed. Now click 3 times, after 5 seconds the Danalock will calibrate.