danalock V3 SCANDI Mounting Manual
Hide thumbs
Also See for V3 SCANDI:
- Instructions manual (20 pages) ,
- Easy install (2 pages) ,
- Quick manual (8 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for danalock V3 SCANDI
Summary of Contents for danalock V3 SCANDI
- Page 1 Danalock V3 SCANDI Mounting guide www.danalock.com...
-
Page 2: Table Of Contents
5. Remove the paper from the stickers page 6. Mounting the backplate on the door page 7. Give the tailpiece the right length page 8. Attach the tailpiece adaptor page 9. Fit and fasten the Danalock page Page 2... - Page 3 12. Activate batteries page 13. Before downloading the app page 14. Download the Danalock app page 15. Open the Danalock app page 16. Dismount instructions page 17. LED-Signals page 18. How to operate the Danalock V3 with click-commands page Page 3...
-
Page 4: Tools Needed
Tools needed: Page 4... -
Page 5: Parts Involved
Parts involved: Tailpiece plate Tailpiece Thumb-turn Page 5... -
Page 6: Secure The Front Lock
1. Secure the front lock Before removing your existing lock, use tape to secure the outside keyhole. This will keep it in place as you remove the screws on the inside. Page 6... -
Page 7: Remove The Inside Thumb-Turn
2. Remove the inside thumb-turn First you have to remove the inside thumb-turn. Set aside the screws. You’ll reinstall them in step 5. Page 7... -
Page 8: Normal Tailpiece Length
3. Normal tailpiece length Most doors have tailpieces that extend 10 mm from the doorplate. They will fit the Danalock without need for any adjustments to their lenght! If the tailpiece is less than 10 mm from the door surface, an extra tailpiece can be found in the Danalock box. -
Page 9: Tailpiece Too Short - Insert A New
If the tailpiece is less than 10 mm you have to remove the plate that holds the tailpiece and replace it with the tailpiece from the Danalock box. You then need to shorten the new tailpiece after you have mounted the back plate. (Read more on p. 12). -
Page 10: Remove The Paper From The Stickers
5. Remove the paper from the stickers Find the backplate in the Danalock box and remove the paper from the three stickers on the backside of the backplate. Page 10... -
Page 11: Mounting The Backplate On The Door
6. Mounting the backplate on the door Place the backplate where the thumb-turn used to be. The round hole in the middle is for the tailpiece. Use the 2 screws from the thumb-turn to attach the backplate. Page 11... -
Page 12: Give The Tailpiece The Right Length
7. Give the tailpiece the right length To avoid damaging the Danalock you will have to shorten the new tailpiece to max. 35 mm from the door surface. Use two pliers or a wire cutter to shorten the tailpiece. max. -
Page 13: Attach The Tailpiece Adaptor
Choose the green tailpiece adaptor from the Danalock box and insert the tailpiece adaptor in the center tube on the backside of the Danalock. Press on the adaptor until a click ensures it is fixed firmly to the Danalock. Page 13... -
Page 14: Fit And Fasten The Danalock
9. Fit and fasten the Danalock Fit the Danalock over the backplate with the battery cover facing down, the tailpiece sliding into the adapter and the backplate notches into the back of the lock. Page 14... -
Page 15: Align The Platemarks
10. Align the platemarks Find the small marking at the edge of the backplate and align it with the hole in the cover ring surrounding the Danalock. Now you are sure to hit the notches on the backplate with the Danalock. -
Page 16: Fasten The Danalock
11. Fasten the Danalock Turn the Danalock clockwise until it clicks to fasten it to the backplate. NOTE: If you need to unfasten and retry, see “Uninstall instructions” on p. 22. Page 16... -
Page 17: Activate Batteries
12. Activate batteries Pull out the plastic tab to activate the batteries. A light will flash to confirm the Danalock is ready. Note: If the batteries are disconnected, you will have to re-calibrate the Danalock. Page 17... -
Page 18: Before Downloading The App
13. Before downloading the app Your Danalock is now attached to the door. Download and open the Danalock app to finish setting it up. Leave the door open, so the lock isn’t influenced when calibrated. Page 18... -
Page 19: Download The Danalock App
14. Download the Danalock app Go to Google Play or App Store and download the Danalock app. When the app is installed you create a user profile by pressing the blue ring. You will use this profile each time you sign into the app. -
Page 20: Open The Danalock App
15. Add the lock in the Danalock app When you have logged in you will see your empty keychain. Press ”Add lock” at the bottom of the screen. A guide will now lead you through the installation and configuration of your Danalock. -
Page 21: Dismount Instructions
16. Dismount instructions If at any time you need to dismount the Danalock from your door, insert a pen tip into the hole at the top inner edge of the lock and press while turning the lock counter-clockwise until the lock releases. -
Page 22: Led-Signals
17. LED-Signals A LED light on the Danalock indicates the status of several operations with different colours: LED-Mode LED colour Status indication Constant red till light finishes Lock has successfully locked Constant green till light finishes Lock has successfully unlocked Constant white for 3 seconds Power on. -
Page 23: How To Operate The Danalock V3
Danalock into locked position and click once. White Auto calibration Turn the Danalock manually until the door is unlocked and leave the door open while calibrating. Lift the handle if needed. Now click 3 times, after 5 seconds the Danalock will calibrate. - Page 24 www.danalock.com...