Figures - IBM Storwize V7000 Quick Installation Manual

Figures

|
1. This figure shows 12 drives and two end caps
| |
(model 2076-112). .
|
2. This figure shows 24 drives and two end caps
| |
(model 2076-124). .
3. Rear view of a model 2076-112 or a model
2076-124 control enclosure .
4. This figure shows the data ports in the rear of
the control enclosure..
5. 10 Gbps Ethernet ports on the rear of the
Storwize V7000 enclosure .
6. Rear view of a model 2076-212 or a model
2076-224 expansion enclosure .
7. SAS ports and LEDs in rear of expansion
enclosure. . .
8. Front view of file module .
9. Rear view of file module
10. Recommended rack locations.
11. Securing an enclosure to a rack cabinet
12. Hole locations in the front of the rack .
13. Hole locations in the back of the rack .
14. Removing the enclosure end cap
15. Securing an enclosure to a rack cabinet
16. Cable management arm box contents. .
17. Friction rail box contents. .
18. Locate a 2U space in the lower section of the
rack. . . . . .
19. Open the rear slide rail hooks. .
20. Install the rear end of the slide rails. .
21. Install the front end of the slide rails. .
22. Install the front end of the slide rails. .
23. Install the file module on the slide rails.
24. Slide the file module into the rack. .
25. Install the cable management support arm. It
can be installed on either side (left or right).
The graphic shows the rear of the rack. .
26. Install the cable management arm. .
27. Adjust the location of the cable management
arm. . . . . .
© Copyright IBM Corp. 2011, 2012
. . . . . . . .
. . . . . . . .
. . . . .
. . . . . . .
. . . . .
. . . .
. . . . . . . . .
. . . . .
. . . . . .
. . . . .
. .
. .
. . . .
. .
. . . . . .
. . . . . . . . .
. . . .
. .
. .
. .
. . .
.
. . .
. . . . . . . . .
28. Connect and route the cables.
. . 4 29. Secure the cable management arm and the file
module in the rack for shipping if needed. .
. . 4 30. Install the front screws.
31. Internal cabling connections between file
. . 4 modules (A & B), control enclosure (C), and
expansion enclosures (D & E). .
. . 5 32. Attaching an expansion enclosure to the
control enclosure .
. . 6 33. Adding a second expansion enclosure.
34. Attaching SAS cables to the enclosures
. . 6 35. Control enclosure Ethernet network
connections. .
. . 7 36. 10 Gbps Ethernet ports on the rear of the
. . 8 Storwize V7000 enclosure .
. . 8 37. File module node Ethernet network
. 11 connections. .
14 38. Diagram showing how to connect the file
. 15 modules to the control enclosure using Fibre
. 16 Channel cables. Refer to previous table. .
. 17 39. Unlocking the cable retention bracket .
18 40. Sliding the cable retention bracket directly
. 19 behind the power cord .
| |
. 20 41. 24 drives and two end caps .
| | 42. 12 drives and two end caps .
. 20 | 43. LEDs on the power supply units of the
. 21 | | expansion enclosure.
. 21 44. LEDs on the power supply units of the control
. 22 enclosure .
. 22 45. Here are examples of IP addresses, machine
23 names, and so forth. The expansion enclosures
. 23 are not shown.
46. Initialization tool welcome panel .
47. Here are examples of IP addresses, machine
. 24 names, and so forth. The expansion enclosures
. 24 are not shown.
. 25
. . .
. . . . .
. .
. . . . . . .
. . . . . . . .
. . . .
. . . . . . . .
. . . . .
. . .
. . .
. . . . . .
. . . . . . . . .
. . . . . . . .
.
. . . . . . . .
. . . 25
. 26
. . . 26
. . . 28
. . . 29
. . . 30
31
. . . 32
. . . 33
. . . 34
. . 37
. . . 38
. . . 39
. . . 40
. . . 40
. . . 41
. . . 42
. . . 45
. . . 49
. . . 52
v