Pentair IntelliFloXF Installation And User Manual page 12

8
MENU
Pump Menu: Settings
SETTINGS
Pump Address
The default pump address is #1 and only needs to be
changed when there is more than one IntelliFloXF
IntelliProXF ® (or IntelliFlo ®
Pump on an automation system. Change the address to
allow the automation system to send a command to the
correct pump.
Use this setting if your pump is connected via the RS-485
COM port to an IntelliTouch
Control System or IntelliComm
For EasyTouch, SunTouch or IntelliComm systems, the
pump only communicates with address #1. The pump
address can be set from 1-16. The IntelliTouch system
can communicate only to four (1-4) pumps.
Note: IntelliFloXF and/or IntelliProXF pumps cannot be
connected in series with other pumps.
1. Be sure the green power LED is on and the pump
is stopped.
2. Press Menu.
3. Press Select for "Settings". Press Select again to
select "Pump Address".
4. To change the pump address, press Select.
5. Press Up or Down arrows to change the address
number from 1-16.
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press Escape to exit.
Set Time
The time controls all scheduled times, functions, and
programmed cycles and stores the correct time for up
to 96 hours after power is turned off. Reset if the power
is off longer than 96 hours.
1. Check that the green power LED is on.
2. Press Menu.
3. Press Select to select "Settings".
4. Use the Up or Down arrows to scroll to "Set Time"
and press Select.
5. Use Up or Down arrows to set the time.
Note: To change AM/PM, increase or decrease
numbers until the desired time is displayed.
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press Escape to exit.
XF
®
INTELLIFLO and INTELLIPRO
and IntelliPro ® ) Variable Speed
, EasyTouch , SunTouch
® ®
Communication Center.
®
XF
®
Variable Speed Pump Installation and User's Guide
Set AM/PM or 24 Clock
To change the time from a 12 hour clock (AM/PM) to a
24 hour clock:
1. Press Menu.
or
®
2. Press Select to select "Settings".
3. Use the Up or Down arrows to scroll to "AM/PM."
4. Press Select to change the setting.
5. Press Up or Down arrows to choose between 24
hr. and AM/PM.
®
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press Escape to exit.
Set Temperature Unit
The default setting is Fahrenheit (°F). The pump can be
set to either Celsius (°C) or Fahrenheit (°F). The Anti
Freeze protection feature (see page 16) can be set to
either Fahrenheit or Celsius.
1. Check that the green power LED is on.
2. Press Menu.
3. Press Select to select "Settings".
4. Use the Up or Down arrows to scroll to "Temperature
Units" menu item. Press Select.
5. Use Up or Down arrows to choose Celsius (°C) or
Fahrenheit (°F).
6. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
7. Press Escape to exit.
Set Screen Contrast
The default setting for the LCD screen is 3. Screen
contrast levels can be adjusted from 1 to 5 units for low
or high lighting conditions.
1. Check that the green power LED is on.
2. Press Menu.
3. Press Select to select "Settings".
4. Use the Up or Down arrow to scroll to "Contrast
Level".
5. Press Select. Screen will show current contrast
setting number.
6. Use Up or Down to change number.
7. Press Enter to save. To cancel any changes, press
Escape to exit without saving.
8. Press the Escape button to exit.