Table of Contents
Advertisement
Quick Links
Wood & Glass TV Stand
for TVs up to 75"
NS-HWG1865
Before using your new product, please read these instructions to prevent any damage.
USER GUIDE
SAFETY INFORMATION AND SPECIFICATIONS .2
PACKAGE CONTENTS: PARTS ..................................3
PACKAGE CONTENTS: HARDWARE .......................4
ASSEMBLY INSTRUCTIONS ......................................6
CARE AND MAINTENANCE ................................... 21
Advertisement
Table of Contents
Related Manuals for Insignia NS-HWG1865
Summary of Contents for Insignia NS-HWG1865
- Page 1 USER GUIDE Wood & Glass TV Stand for TVs up to 75” NS-HWG1865 SAFETY INFORMATION AND SPECIFICATIONS .2 PACKAGE CONTENTS: PARTS ........3 PACKAGE CONTENTS: HARDWARE .......4 ASSEMBLY INSTRUCTIONS ........6 CARE AND MAINTENANCE ........21 Before using your new product, please read these instructions to prevent any damage.
-
Page 2: Safety Information And Specifications
NS-HWG1865 SAFETY INFORMATION AND SPECIFICATIONS CAUTION: The console’s top work surface is designed for use with a product weighing no Maximum overall weight: 335 lbs (151.9 kg) more than 135 lbs. (61.2 kg) and having a width that permits it to sit evenly on the Maximum top panel weight: 135 lbs (61.2 kg) -
Page 3: Tools Needed
Wood & Glass TV Stand Tools needed: Phillips screwdriver Hammer 3/8” drill bit Rubber mallet Power drill PACKAGE CONTENTS: PARTS Make sure that you have all the parts necessary to assemble your new TV stand. B Left side panel (1) C Right side panel (1) A Top panel (1) Note: Keep the stopper template attached to the top panel. -
Page 4: Package Contents: Hardware
NS-HWG1865 PACKAGE CONTENTS: HARDWARE Note: You may receive extra hardware. Make sure that you have all the hardware necessary to assemble your new TV stand. Label Hardware Qty. Label Hardware Qty. Shelf support Wood dowel M8 x 30 mm Cam pin... - Page 5 Wood & Glass TV Stand INSTALLATION TIPS Gluing wood dowels (N) When using a wood dowel (N), put one drop of glue (CC) in the hole before you insert the wood dowel (N). Insert the wood dowel (N), then gently tap it with a rubber mallet to secure it in place. FINAL Locking cam pins (P) and cam locks (Q) 1 One end of a cam pin (P) is threaded so that it screws into place.
-
Page 6: Assembly Instructions
NS-HWG1865 ASSEMBLY INSTRUCTIONS Step 1: Screw cam pins onto the top panel, bottom shelf, and skirtings Tip: Assemble your stand on a carpeted floor or the empty TV stand carton to avoid scratching it. • Securely screw the cam pins (P) into the designated small holes on the top panel (A), bottom shelf (E), front skirting (F) and side skirtings (H and I) using a Phillips screwdriver. - Page 7 Wood & Glass TV Stand Step 2: Attach the back skirting between the side skirtings 1 Glue two wood dowels (N) into the drilled holes on the ends of the back skirting (G). Tip: See “Gluing wood dowels (N)“ on page for more information.
- Page 8 NS-HWG1865 Step 3: Attach the front skirting to the side skirtings 1 Glue two wood dowels (N) into the drilled holes on the front skirting (F). 2 Attach the front skirting (F) to the side skirtings (H and I) by inserting two cam locks (Q) and tightening with a screwdriver.
- Page 9 Wood & Glass TV Stand Step 4: Attach the assembled base to the bottom shelf 1 Glue 10 wood dowels (N) into the drilled holes on the bottom shelf (E). 2 Position the assembled base onto the wood dowels (N) and cam pins (P) on the bottom shelf (E). Make sure that the pilot holes for the corner connectors face the front of the bottom shelf.
- Page 10 NS-HWG1865 Step 5: Install two floor levelers to the assembled base 1 Using the pilot holes as a guide, fasten two corner connectors (Z) to the joints where the front skirting (F) meet with the side skirtings (H and I) with eight 15 mm flat head screws (S).
- Page 11 Wood & Glass TV Stand Step 6: Attach two door stoppers to the top panel Note: Keep the stopper template attached to the top panel (A). • Using the pilot holes as a guide, attach two door stoppers (U) onto the front supports on the top panel (A) with two 15 mm flat head screws (S) per stopper.
- Page 12 NS-HWG1865 Step 7: Align and attach the side panels to the top panel 1 Glue two wood dowels (N) into the holes on the top edge of the left side panel (B). 2 Attach the left side panel to the top panel (A) by inserting two cam locks (Q) and tightening with a screwdriver.
- Page 13 Wood & Glass TV Stand Step 8: Attach the partition panel to the top panel 1 Glue two wood dowels (N) into the inner holes on the top edge of the partion panel (D). 2 Attach the partition panel to the top panel (A) by inserting two cam locks (Q) and tightening with a screwdriver. Door hinge mounting bases point towards the front of the unit You’ll need:...
- Page 14 NS-HWG1865 Step 9: Attach the bottom shelf to both side panels and partition panel 1 Glue six wood dowels (N) into the holes on the bottom edge of side panels (B and C) and partition panel (D). 2 Align the drilled holes on the bottom shelf (E) with the installed wood dowels (N) on both side panels (B and C) and partition panel (D), then press them together.
- Page 15 Wood & Glass TV Stand Step 10: Attach the back panel to the assembled console frame 1 Go back and tighten all cam locks and screws. Make sure that all the parts are tight and there are no gaps between the pieces. This will help keep the unit square. 2 Turn the assembled unit over so that its back is facing up.
- Page 16 NS-HWG1865 Step 11: Attach adjustable shelves 1 Stand the assembled unit upright. 2 Insert the cam lock covers (V) into the cross slots on the visible cam locks on the vertical panels (B, C, and D). 3 Insert eight shelf supports (W) into the holes in the sides of the compartments. Make sure that you place the shelf supports at the same level so the shelves are not tilted.
- Page 17 Wood & Glass TV Stand Step 12: Attach doors to the vertical panels 1 Push the knob bolts (Y) through the inside of each door (L), then screw on the knobs (X). 2 Attach a door (L) to the right side panel (C) by engaging both door hinges together as shown: A Extend both hinges of the door (L) to the open position, if needed.
- Page 18 NS-HWG1865 Step 13: Attach the stopper to the top panel To prevent your TV from tipping, you must follow these instructions if you place a TV on top of your stand. Otherwise, skip to “Step 14: Change the door panel” on page 19.
- Page 19 Wood & Glass TV Stand Step 14: Change the door panel Follow these steps if you want to change your TV stand’s door panels from glass to wood. Otherwise, skip to “Step 15: Position the TV stand and install the tipping restraint hardware kit”...
- Page 20 NS-HWG1865 Step 15: Position the TV stand and install the tipping restraint hardware kit 1 Position the assembled stand against the wall where you plan to use it. 2 Adjust the leveling feet to level the TV stand. 3 Follow the instructions printed on the bag containing the tipping restraint hardware kit (EE) to attach the restraint hardware to the wall and the stand.
-
Page 21: Care And Maintenance
Wood & Glass TV Stand CARE AND MAINTENANCE Wood/Laminate • Use your favorite type of furniture polish. • Do not spray polish directly onto the stand. Spray onto a soft cloth then wipe the stand. • Clean spills immediately with a soft, damp cloth. •... - Page 22 DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND Insignia and are not returned to you. If service of Products or NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY parts are required after the Warranty Period expires, you must AFTER THE WARRANTY PERIOD.
- Page 23 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies. Registered in some countries. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2017 Best Buy. All rights reserved.