Related Manuals for Seco SECOCQ7-mITX2.0
Summary of Contents for Seco SECOCQ7-mITX2.0
- Page 1 SECOCQ7-mITX2.0 ® and μQseven ® Carrier Board for Qseven modules, Rel.2.0 compliant, on mini ITX form factor SECOCQ7-mITX2.0...
-
Page 2: Revision History
SECO S.r.l. is prohibited. Every effort is been made to ensure the accuracy of this manual; however, SECO S.r.l. accepts no responsibility for any inaccuracies, errors or omissions herein. SECO S.r.l. reserves the right to change precise specifications without prior notice to supply the best product possible. - Page 3 3.3.17 SPI Pin Header ..........................35 3.3.18 SPI Flash socket .......................... 36 3.3.19 LPC Pin Header ........................... 36 3.3.20 FAN Connector ..........................36 3.3.21 Front Header Interface ......................... 37 3.3.22 MFG Connector ........................... 37 Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0...
-
Page 4: Chapter 1 Introduction
User Manual - Rev. First Edition: 1.0 - Last Edition: 1.0 - Author: S.B. - Reviewed by G.M. Chapter 1 INTRODUCTION Warranty Information and assistance RMA number request Safety Electrostatic Discharges RoHS compliance Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0... -
Page 5: W Arranty
Costs for replaced components will be calculated aside. Warning! All changes or modifications to the equipment not clearly approved by SECO S.r.l. could impair equipment’s functionality and lead to the expire of the warranty Copyright © 2013 SECO S.r.l. -
Page 6: I Nformation And Assistance
In most of the cases you can find useful information to resolve your problem. SECO reseller: the reseller or agent can help you in determining the exact cause of the problem and search the best solution for it. -
Page 7: E Lectrostatic D Ischarges
So whenever handling a SECOCQ7-mITX2.0 board, take care to ground yourself through an anti- static wrist strap. Placement of the board on an anti-static surface is also highly recommended. -
Page 8: Chapter 2 Overview
Page 8 User Manual - Rev. First Edition: 1.0 - Last Edition: 1.0 - Author: S.B. - Reviewed by G.M. Chapter 2 OVERVIEW Introduction Technical Specifications Mechanical specifications Electrical specifications Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0... -
Page 9: I Ntroduction
Page 9 User Manual - Rev. First Edition: 1.0 - Last Edition: 1.0 - Author: S.B. - Reviewed by G.M. 2.1 Introduction SECOCQ7-mITX2.0 is a carrier board, designed in mini-ITX form factor, intended for the use with ® any Qseven CPU modules Rel. -
Page 10: T Echnical S Pecifications
ATX Standard Power connector (AT mode configurable) Temperature Range: 0 to 60° C 170 x 170 mm (6.693” x 6.693”) Dimensions: ® and μQseven ® Support for Qseven CPU modules ® Compliant to Qseven Specifications rel. 2.0 Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0... -
Page 11: M Echanical Specifications
® In order to fix the Qseven module to the carrier board, on SECOCQ7-mITX2.0 have been soldered four metallic spacers, height 4mm, 2.5mm diameter. Two spacers (those closer to MXM connector) are always present, the other two spacers can be ®... -
Page 12: E Lectrical Specifications
User Manual - Rev. First Edition: 1.0 - Last Edition: 1.0 - Author: S.B. - Reviewed by G.M. 2.4 Electrical specifications SECOCQ7-mITX2.0 board needs to be supplied using a standard ATX Power Supply. The board, however, can also be configured to work in AT mode. - Page 13 CAUTION: handling batteries incorrectly or with not-approved devices may present a risk of fire or explosion. Batteries supplied with SECOCQ7-mITX2.0 board are compliant to requirements of European Directive 2006/66/EC regarding batteries and accumulators. When putting out of order SECOCQ7- mITX2.0 board, remove the batteries from the board in order to collect and dispose them according to the requirement of the same European Directive above mentioned.
-
Page 14: Chapter 3 Connectors
Page 14 User Manual - Rev. First Edition: 1.0 - Last Edition: 1.0 - Author: S.B. - Reviewed by G.M. Chapter 3 CONNECTORS Connectors placement - Overview Connectors overview Connectors Description Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0... -
Page 15: C Onnectors Placement - O Verview
User Manual - Rev. First Edition: 1.0 - Last Edition: 1.0 - Author: S.B. - Reviewed by G.M. 3.1 Connectors placement - Overview In the following picture, it is shown the connectors placement of SECOCQ7-mITX2.0 carrier board. Standard connectors are placed on the same side of PCB, so that it is possible to place them on a panel of an eventual enclosure. -
Page 16: C Onnectors Overview
CN33 External Camera Interface CN15 LVDS/eDP connector CN34 CSI interface CN16 Display EEPROM socket CN37 Optional USB 2.0 type A port #0 CN17 Backlight connector CN38 Optional USB 2.0 ports# 6-7 CN18 Feature connector Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0... -
Page 17: C Onnectors D Escription
SATA0_Tx- SATA1_Tx- SATA_ACT# SATA0_Rx+ SATA1_Rx+ SATA0_Rx- SATA1_Rx- BOOT_ALT# (*) SDIO_CLK# SDIO_CD# SDIO_LED SDIO_CMD SDIO_WP SDIO_PWR# SDIO_DAT1 SDIO_DAT0 SDIO_DAT3 SDIO_DAT2 SDIO_DAT5 SDIO_DAT4 SDIO_DAT7 SDIO_DAT6 RSVD HDA_SYNC/I2S_WS SMB_CLK HDA_RST#/I2S_RST# SMB_DAT HDA_BITCLK/I2S_CLK SMB_ALERT# HDA_SDI/I2S_SDI GP0_I2C_CLK HDA_SDO/I2S_SDO GP0_I2C_DAT Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0... - Page 18 LVDS_BLT_CTRL GP_1-Wire_Bus LVDS_DID_DAT eDP0_HPD# LVDS_DID_CLK eDP1_HPD# CAN0_TX CAN0_RX DP_LANE3+/TMDS_CLK+ RSVD_132 DP_LANE3-/TMDS_CLK- RSVD_134 DP_LANE1+/TMDS_LANE1+ 138 DP_AUX+ DP_LANE1-/TMDS_LANE1- DP_AUX- DP_LANE2+/TMDS_LANE0+ 144 RSVD_144 DP_LANE2-/TMDS_LANE0- RSVD_146 DP_LANE0+/TMDS_LANE2+ 150 HDMI_CTRL_DAT DP_LANE0-/TMDS_LANE2- HDMI_CTRL_CLK DP_HDMI_HPD# RSVD_154 PCIE_CLK_REF+ PCIE_WAKE# PCIE_CLK_REF- PCIE_RST# Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0...
- Page 19 (*)BOOT_ALT# Signal: this signal can be necessary to the Qseven onboard BIOS (x86 modules) or enable different boot devices (most of all, for ARM modules). For this reason, on SECOCQ7-mITX2.0 carrier board there is a dedicated jumper, JP10, which allows external driving of BOOT_ALT# signal.
-
Page 20: Lvds / Embedded Display Port Connector
User Manual - Rev. First Edition: 1.0 - Last Edition: 1.0 - Author: S.B. - Reviewed by G.M. 3.3.2 LVDS / embedded Display Port Connector SECOCQ7-mITX2.0 board can be interfaced to LCD displays using its LVDS/eDP interface, which allows the connection of displays with a colour depth of 18 or 24 bit, single or dual channel. -
Page 21: Display Id Eeprom Socket
C EEPROM programmed with correct data. For this purpose, an 8-pin DIP socket p2.54mm, type TE p/n 2-1571552-2 or equivalent is provided, with the following pinout: Display ID EEPROM socket – CN16 Signal Signal +3.3V_S LVDS_DID_CLK LVDS_DID_DAT Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0... -
Page 22: Displayport / Hdmi Connector
IC, Texas Instruments SN75DP122A DisplayPort 1:2 Switch With Integrated TMDS Translator. In this factory configuration, it is necessary to configure properly jumpers JP1 and JP2 for switching between Display Port and HDMI. JP1 jumper position JP2 jumper position HDMI Use Display Port Use Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0... -
Page 23: Camera Interfaces
SECOQseven modules has an additional FFC/FPC connector on a side, always in the same position, with a standardised pinout. On SECOCQ7-mITX2.0 carrier board, therefore, there is an identical FFC/FPC connector, type ® HIROSE p/n FH12A-36-S-0.5SH(55), near the position of Qseven module Camera connector, to allow the connection of module’s ISP to an external camera directly through dedicated connector... - Page 24 40G-415 or equivalent. External Camera Connector – CN33 Signal Signal Cam_External_Clock_A CAM_EXP0 Cam_External_Clock_B CAM_EXP1 CAM_PCLK CAM_EXP2 CAM_VS CAM_EXP3 CAM_HS CAM_EXP4 CAM_FIELD CAM_EXP5 CAM_D0 CAM_EXP6 CAM_D1 CAM_EXP7 CAM_D2 CAM_EXP8 CAM_D3 CAM_EXP9 CAM_D4 CAM_EXP10 CAM_D5 CAM_EXP11 CAM_D6 CAM_EXP12 Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0...
- Page 25 CSI_DATA1- CAM_EXP11 CSI_DATA1+ CAM_EXP12 ---- CSI_CLK- CAM_EXP7 RSVD_132 CSI_CLK+ CAM_EXP8 RSVD_134 CSI_DATA0- CAM_EXP9 RSVD_144 CSI_DATA0+ CAM_EXP10 RSVD_146 CSI_PWWDN CAM_EXP4 ---- CSI_XCLK CAM_External_Clock_A RSVD_154 CSI_SCL CAM_I2C_SCL GP0_I2C_CLK CSI_SDA CAM_I2C_SDA GP0_I2C_DAT CSI_RESET# CAM_RESETB LPC_RST# Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0...
-
Page 26: Audio Section
+5V_S S/PDIF_OUT In order to give the maximum audio capabilities to SECOCQ7-mITX2.0 carrier board, it is also available a dedicated 9-pin 2.54mm pitch Pin header for external connection of a second Line In and a second Mic In (these are managed by the same Realtek ALC886-GR HD Audio Codec). -
Page 27: Usb 2.0 + Gigabit Ethernet Combo Connector
USB_P2+ USB_P2- +5V_S USB_P3+ USB_P3- On the connectors there are also two LEDS. Left LED is bicolour, Green/Orange, and shows 10/100 or 1000 connection. Right LED is Orange, and shows ACTIVITY on the LAN. Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0... -
Page 28: Factory Alternatives Usb 2.0 / Usb 3.0 Connectors
USB3.0 ports on the golden finger connector, by sharing the Superspeed lanes of USB3.0 ports with pre-existing USB2.0 ports 4÷7. For this reason, it is given the possibility of ordering SECOCQ7-mITX2.0 carrier board in the following configurations: A) With one type A USB3.0 port or B) With one additional type A USB2.0 port + 2 internal USB2.0 ports... - Page 29 In case the port is set to work in Client Mode, then +5V voltage CLIENT must come from external Host (it is used to recognize when the host is connected to the carrier board). USB port #1 mode Inserted Host Not inserted Client Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0...
-
Page 30: Pci Express X16 Expansion Slot
User Manual - Rev. First Edition: 1.0 - Last Edition: 1.0 - Author: S.B. - Reviewed by G.M. 3.3.10 PCI Express x16 Expansion Slot SECOCQ7-mITX2.0 board offer the possibility of expansion using a standard PCI Express x16 card edge connector (PCI-e x4 electrical), type TYCO p/n 2-1612163-4 or equivalent. - Page 31 B66 --- B67 --- B68 GND B69 GND B70 --- B71 --- B72 GND B73 GND B74 --- B75 --- B76 GND B77 GND B78 --- B79 --- B80 GND B81 PRSNT#2 B82 --- Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0...
-
Page 32: Serial Ports
Serial port (TX/RTS#/RX/CTS# signals, pins 171, 172, 177, 178 of the connector) at TTL level. Since most common use of Serial ports require that they are available at RS-232 electrical level, on SECOCQ7-mITX2.0 Carrier board it has been integrated an RS-232 transceiver. -
Page 33: Sd/Mmc Card Connector
Since Qseven standard contemplates signals for Secure Digital Input/Output and MultiMedia Cards, on SECOCQ7-mITX2.0 board there is also a socket, for the use of standard SD or MMC ® cards, to be used as Mass Storage Device and/or Boot Device (if the Qseven module you are using with this carrier board implements this functionality). -
Page 34: Msata Slot
For this purpose, connected to I2C bus, there is an 8-pin DIP socket p.54mm, type TE p/n 2- 1571552-2 or equivalent, with the following pinout: I2C EEPROM socket – CN20 Signal Signal +3.3V_S GP0_I2C_CLK GP0_I2C_DAT Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0... -
Page 35: Feature Connector
10 pin, P2.54mm standard pin header, with the following pinout. SPI Pin Header – CN24 Signal Signal +3.3V_S +3.3V_S SPI_CS0# SPI_MOSI SPI_CS1# SPI_MISO 1-Wire_Bus SPI_SCK Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0... -
Page 36: Spi Flash Socket
Qseven module used and, eventually, on BSP programming. 3.3.20 FAN Connector SECOCQ7-mITX2.0 carrier board is able to manage both +5VDC and +12VDC fans, with speed ® control (speed control can be used only if your Qseven module supports this feature, using signals FAN_TACHOIN and FAN_PWMOUT). -
Page 37: Front Header Interface
+5V_S 3.3.21 Front Header Interface To allow the integration of a SECOCQ7-mITX2.0 based system inside a box PC-like, there is a connector on the Carrier Board that allows to remote signals for the Power Button (to be used to put the system in a Soft Off State, or awake from it), for the Reset Button, and the signal for an optional LED signalling activity on SATA Channel. - Page 38 JP8 jumper position UART1_RX (RS-232 level) JTAG_TDI Please notice that for correct working of the module, both JP8 and JP9 must be in the same position (i.e., both in 1-2 or in 2-3 position). Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0...
- Page 39 SECOCQ7-mITX2.0 Page 39 User Manual - Rev. First Edition: 1.0 - Last Edition: 1.0 - Author: S.B. - Reviewed by G.M. www.seco.com Copyright © 2013 SECO S.r.l. SECOCQ7-mITX2.0...