Table Of Contents - Barco ZEUS Installation And Safety Manual

Table Of Contents

Software License Agreement3
Welcome7
About This Manual8
Safety9
General Considerations10
Safety Training To Be Provided By The Installer11
Important Safety Instructions12
Light Beam Hazard Distance (Hd)16
Hd In Function Of The Lens Throw Ratio (Tr)18
Getting Started19
Installation Requirements21
Projector Weight22
Unpacking The Projector23
Initial Inspection25
Installation Process27
Installation Process Overview28
Physical Installation29
Positioning The Zeus Projector At Port Window30
Projector Tilting31
Installation Of The Exhaust System33
Connecting The Projector With The Power Net35
Lenses & Lens Selection37
Available Lenses38
Lens Selection39
Lens Installation40
Lens Removal41
Lens Shift, Zoom & Focus42
Input & Communication45
Introduction46
Local Keypad47
Projector Status49
Integrated Cinema Processor (Icp)50
Hd-Sdi Input Module (Optional)51
Integrated Media Block/Server (Optional)54
Cinema Controller55
Icmp57
Icmp Introduction58
Icmp Hdd59
Icmp Communication Ports60
Icmp Source Input Ports62
Icmp Reset Button And Status Leds65
Icmp Hdd Status Leds66
Icmp Device Certificate68
Icmp Configuration Via Communicator70
Obtaining The Barco Icmp Certificate71
Removing A Hdd Form The Icmp72
Installing A Hdd Into The Icmp73
Communicator Touch Panel75
Installing The Touch Panel Interface78
Repositioning The Touch Panel Interface80
Starting Up81
Switching The Zeus Projector On82
Switching The Zeus Projector Off83
Scheimpflug85
Scheimpflug Introduction86
Scheimpflug Adjustment88
Fixation Of The Lens Holder Front Plate90
Back Focal Length Adjustment92
Convergence97
Convergence Controls98
Preparing For Convergence Adjustment100
Converging The Blue Pattern Onto The Red Pattern101
Converging The Green Pattern Onto The Red Pattern102
Closing Off The Light Processor Compartment103
Lamp House & Lamp Replacement105
Supported Xenon Lamps108
Lamp Replacement Process109
Removal Of The Lamp House111
Removal Of The Xenon Lamp From The Lamp House112
Installation Of The Xenon Lamp Into The Lamp House117
Installation Of The Lamp House122
Resetting The Lamp Parameters123
Realignment Of The Lamp In Its Reflector126
Preventative Maintenance Actions129
Month Maintenance Actions130
Lamp Change Maintenance Actions132
Maintenance Procedures133
Check The Large Dust Filter134
Check The Small Dust Filter136
Vacuum Cleaning Of The Dust Filters138
Washing And Drying The Dust Filters139
Cleaning The Lens140
Cleaning The Exterior Of The Projector141
Cleaning The Uv Blocker Of The Lamp House142
Cleaning The Reflector Of The Lamp House143
Authorization To Clear Security Warning On The Projector144
Removal And Installation Of The Projector Covers145
Removal Of The Lamp House Cover146
Removal Of The Rear Cover147
Removal Of The Top Cover148
Removal Of The Left Side Cover149
Removal Of The Top Cover Plate Of The Light Processor Compartment150
Removal Of The Side Cover Plate Of The Light Processor Compartment152
Installation Of The Side Cover Plate Of The Light Processor Compartment153
Installation Of The Top Cover Plate Of The Light Processor Compartment154
Installation Of The Left Side Cover156
Installation Of The Top Cover157
Installation Of The Rear Cover158
Installation Of The Lamp House Cover159
Specifications161
Specifications Of The Zeus Projector162
Specifications Of The Icmp164
Specifications165
Dimensions Of The Zeus Projector166
Dimensions Of The Universal Pedestal167
Technical Regulations168
Pin Configurations169
About General Purpose Inputs & Outputs (Gpio)170
Pin Configurations Of The Cinema Controller Communication Ports172
Pin Configurations Of The Icmp Communication Ports173
Environmental Information177
Disposal Information178
Rohs Compliance179
Hazards181
Production Address182
Importers Contact Information183
Glossary185
Index187