Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Barco R5976907/00
Summary of Contents for Barco R5976907/00
- Page 1 R5976907/00 02/11/2005 D-Cine Premiere DP100 User’s manual R9010111 R9010118...
- Page 2 Barco nv Digital Cinema Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.84.93 Fax: +32 56.36.88.62 E-mail: info.bdc.bps@barco.com Visit us at the web: www.barco.com Printed in Belgium...
- Page 3 The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period.
-
Page 5: Table Of Contents
Installation of the lamp unit in the projector head ....... . - Page 6 Table of contents R5976907 D-CINE PREMIERE DP100 02/11/2005...
-
Page 7: Safety Instructions
Always have service on this projector performed by authorized Barco service personnel. 1.3 Ventilation Slots and Openings Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the projector and to protect it from overheating, NEVER cover or block these openings. Projector room Projection room must be well ventilated or cooled in order to avoid build up of heat. -
Page 8: Service
Refer all projector servicing to a qualified Barco service center. Replacement Parts When replacement parts are required, be sure the service technician has used original Barco replacement parts or authorized re- placement parts which have the same characteristics as the Barco original parts. -
Page 9: Check Up The D-Cine Premiere Dp100
In order to ensure that correct internal airflow is maintained, and that the projector complies with Electro-Magnetic Compatibility requirements, it should always be operated with all of it’s covers in place. Never operate the projector with the cover removed, the arc lamp power supply has a 35kV strike pulse mechanism, which is active during lamp switch-on. -
Page 10: Power Connection To Wall Outlet
Reading out the pressure value on the manometer At the top, inside the projector head, a manometer is provided, being part of the cooling circuit. The value in normal operation condition must be approximately 1 Bar with a minimum of 0.5 Bar. -
Page 11: Exhaust On Dirt
A rapid/significant drop in system pressure indicates leakage. Verify whether the circuit shows any visible signs of liquid leakage. Refer the problem to a qualified Barco service center. Minor drops in pressure over time are to be expected. Once the minimum pressure is reached, pre-pressurize to approximately 1 bar (projector off). - Page 12 2. Check up the D-Cine Premiere DP100 R5976907 D-CINE PREMIERE DP100 02/11/2005...
-
Page 13: Starting Up The D-Cine Premiere Dp100
Note: Ensure that the power tumbler switch on the input panel on the projector head is in the ON state After power On switching, the projector boots up for a while (±30s) and the final status of the projector is as follows: (image 3-2,... - Page 14 MACRO 05 MACRO 07 MACRO 09 MACRO 11 MACRO 13 Image 3-2 Control panel status after switching on Image 3-3 Status lights on projector head MACRO 02 MACRO 04 MACRO 06 MACRO 08 MACRO 10 MACRO 12 MACRO 14 R5976907 D-CINE PREMIERE DP100 02/11/2005...
-
Page 15: Starting Image Projection
The dowser opens, indicated by the built-in Green LED ON (B2). 3. Press the desired selection button (D),1 to 14 (image 3-4) The selected button is indicated by the built-in Green LED ON (D1). The projector starts executing the macro actions. Image 3-4... -
Page 16: Using The Touch Screen Panel
About stored Macro’s Many macro’s can be programmed with the D-Cine communicator and stored in the projector. Because the touch screen can display maximum 8 different macro’s, the number of macro’s (if more than 8) is split over more pages. -
Page 17: Cinema Operation
4. CINEMA OPERATION Introduction This section explains how trained operators can use the projector for presenting cinema events such as first-run movies stored an a digital media storage device. The digital media storage device or cinema server is connected to one of the A or B input port on the input panel. - Page 18 4. Cinema Operation The assigned macro is activated resulting in a full image display according the cinema processing procedure (pre-defined by the producers). Image 4-3 Macros selection R5976907 D-CINE PREMIERE DP100 02/11/2005...
-
Page 19: Non-Cinema Operation
This section explains how to display “alternative content” originating from a standard definition or high definition non-cinema source. Such a source routes to a DVI (Digital Visual Interface) port in the D-Cine Premiere DP100 projector head, and bypass cinema processing when selected. -
Page 20: Selecting An Acsar 2 Source
About Macro’s files For any display, the projector interprets incoming signal data according to a selectable “Macro file” defined at the time of installation or later (e.g. with each subsequent release of a new digital cinema feature), and stored in projector memory. -
Page 21: Remote Control Functionality
On the front of the button panel, a window (A) is provided behind which an infra red reception diode is mounted. To send commands to the projector head, point the front of the Remote Control to that window. Image 5-5 Pointing the Remote Control Function of the control LED’s below touch button panel... -
Page 22: Remote Control Functions
Press pause key to stop image display. The image disappear but full power is retained for immediate restart when pause key is pressed again. After power on the projector, pressing this key starts ignition of the lamp. Pressing again, turns of the lamp. -
Page 23: Adjusting The Non-Cine Display
Image keys 5.4.3 Adjusting the Non-Cine Display Overview The projector has a box like menu structure which allows easy access to different menu items for setting up source loading, image layout and projector parameters. Main Menu Image 5-7 Overview Menu structure For more detail about setting up the different items, please refer to the installation manual of the D-Cine Premiere DP100. - Page 24 5. Non-Cinema Operation R5976907 D-CINE PREMIERE DP100 02/11/2005...
-
Page 25: Switching Off The D-Cine Premiere Dp100
1. Press the tumbler switch (A) in the “O” position (OFF state) (image 6-2) All parts of the projector have been powered off. 2. If the projector will not be used for a long period, pull out the power connector from wall outlet. R5976907 D-CINE PREMIERE DP100 02/11/2005... - Page 26 6. Switching Off the D-Cine Premiere DP100 Image 6-2 Powering off the projector R5976907 D-CINE PREMIERE DP100 02/11/2005...
-
Page 27: Maintenance Of The D-Cine Premiere Dp100
How to remove the Lamp unit 1. Loosen the 2 spring screws (A) securing lamp assembly to projector base. 2. Grip the lamp assembly by the bottom handle (B)and partially slide it out of the projector main frame. (image 7-2) Caution: Beware of the weight of the lamp assembly. -
Page 28: Installation Of The Lamp Unit
How to install the lamp unit 1. Place the lamp unit on the lamp base in the projector, lining up the lamp unit foot with the slots on the base. (image 7-3) 2. Push the lamp unit foot fully into the slots. (image 7-4) 3. -
Page 29: Closing The Lamp House Door
Before using the lamp, Insert the lamp parameters via the D-Cine Communicator software. 7.1.2.2 Closing the Lamp house door Installation of a new lamp requires alignment of the lamp position when installed in the projector head. There- fore, first proceed to lamp alignment before closing the lamp house door. - Page 30 7. Maintenance of the D-Cine Premiere DP100 R5976907 D-CINE PREMIERE DP100 02/11/2005...
-
Page 31: Cleaning Air Duct
These items should be cleaned monthly under normal environment conditions. Equipment in very dusty or otherwise contaminated areas may require more frequent maintenance. If the air filters are not regularly cleaned, the air flow inside the projector could be disrupted and cause over- heating. Overheating may lead to the projector shutting down during operation. - Page 32 1. Front air filter: grasp the decorative bar of the filter (A) and pull out the air filter of the projector front cover. 2. Side air filter projector head (A): loosen the 2 screws securing the air filter frame to the side cover and remove the filter.
-
Page 33: Image Control
: jump to bottom of the test pattern list. 3. Press touch button Enable Test Pattern to activate the selected test pattern. Projector displays the selected pattern and the name of the pattern appears in the screen field just below Active test pattern. (image 9-2) 4. -
Page 34: Preparation Of The Projector
Right side cover removal Loosen the dust sock around the lens 1. Pull out the sock fixations from the lens holder and slide it to the front of the projector (only a few points are indicated on the image). (image 9-4) -
Page 35: Lens Focus
Image 9-5 Lens Zoom 9.2.3 Lens Focus The focus adjustment is located just below the lens on the left side (C on image 9-6). Remove the side cover nearest the lens and open the dust sock around the lens. How to focus? 1. - Page 36 9. Image Control 2. Shift the image by turning the knurled torque knob (A2) clockwise or counter clockwise until the image is on the desired position. 3. Secure this position by fastening nut A1 again. 4. For a horizontal shift, loosen first fixation nut B1. 5.
-
Page 37: Status Of The D-Cine Premiere Dp100
Status lights On top of the projector head, rear side, status lights are built-in in the corners. When no errors, e.g. fan failure, overheating.. are detected, the color of the status lights is GREEN. When an error occurs, the color of the status lights changes to RED. Information about the type of error can be retrieved using the D-Communicator or the Touch panel menu. -
Page 38: Temperature Overview
10. Status of the D-Cine Premiere DP100 Image 10-4 Status start up Overview of the Status menu The status menu contains the following items: • Temperature overview • Voltage overview • Fan speeds overview 10.2 Temperature overview To get DMD temperatures and lamp house temperature 1. - Page 39 The switched mode power supply temperatures are listed. (image 10-11) Switched mode power supply 1 primary side Switched mode power supply 1 secondary side Switched mode power supply 2 primary side Switched mode power supply 2 secondary side Image 10-8 More temperature overviews selected Image 10-10 More temperature overviews selected...
-
Page 40: Voltage Overview
10. Status of the D-Cine Premiere DP100 Image 10-12 10.3 Voltage overview First voltage overview 1. Push Voltages. (image 10-13) The first voltage menu will be displayed. (image 10-14) The following voltages are monitored: 5V standby 12V standby 3.3V Image 10-13 Status voltages selected Second voltage overview 1. -
Page 41: Fan Speed Overview
The second voltage overview window will be displayed. (image 10-16) The following voltages are monitored: Lamp fan Top Lamp fan Anode Lamp fan Cathode Electronic fans Image 10-15 Selecting second voltage overview Third voltage overview 1. Push More →. (image 10-17) The third voltage overview window will be displayed. - Page 42 10. Status of the D-Cine Premiere DP100 Image 10-19 Fan speed selected Second fan speed window 1. Push More →. (image 10-21) The second fan speed overview window will be displayed. (image 10-22) The following fans are monitored: Fan sealing Fan lamp top Fan lamp anode Fan lamp cathode...
-
Page 43: D-Cine Premiere Dp100 Info
11.1 Starting up the Menu How to select! 1. On the touch screen panel, starting from the Home screen, consecutively press touch button Home and Projector. (image 11-1) On the touch screen appears two fields, named the Lamp Info and the projector Properties. -
Page 44: Projector Properties
Version of the lamp module Serial number Serial number of the actual installed lamp Image 11-6 More lamp info 11.3 Projector properties Overview • Projector properties start up • IP addresses projector • IP cinema • Communication • Touch panel... -
Page 45: Projector Properties Start Up
IP address when a computer is plugged into a different place in the network. Overview 1. Push IP Projector. (image 11-10) R5976907 D-CINE PREMIERE DP100 02/11/2005 11. D-Cine Premiere DP100 Info Image 11-9... -
Page 46: Ip Cinema
: fixed IP address used for the projector Note: An enabled DHCP, ALWAYS requires an installed network connection to the projector. Without network connection, the projector goes down in network error, by which the operation of the projector is no more guaranteed. -
Page 47: Communication
This panel gives the software version of the touch panel. R5976907 D-CINE PREMIERE DP100 02/11/2005 Image 11-13 IP cinema overview communication address of the projector communication velocity RS232 or RS422 ON or OFF. Only used when Mode is RS422. Image 11-15 Communication properties 11. - Page 48 11. D-Cine Premiere DP100 Info Image 11-16 Touch panel overview selected Image 11-17 Touch panel software version R5976907 D-CINE PREMIERE DP100 02/11/2005...
-
Page 49: Index
R5976907 D-CINE PREMIERE DP100 02/11/2005 Removal Lamp house door Closing Lamp unit 23–24 Access Installation Removal Replacement Lens adjustment 29–31 Focus Projector preparation Zoom 30–31 Lens focus Maintenance Projector Non-Cine display Adjusting Non-Cinema operation Power connection Powering off Projector Pressure... - Page 50 Index Image projection Switching off Projector Switching On Projector Touch panel 33–34, 36–37, 39–43 Projector functions 39–43 Communication IP addresses projector IP cinema Lamp info Properties Properties start up Touch panel properties Status 33–34, 36–37 Fan speed Startup Temperature Voltage...
- Page 51 Revision Sheet Barco nv Digital Cinema/Documentation Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.84.93, Fax: +32 56.36.88.62 E-mail: service.digitalcinema@barco.com, Web: www.barco.com From: Date: Please correct the following points in this documentation (R5976907/00): page wrong R5976907 D-C DP100 02/11/2005 REMIERE correct...