General Operation - Toro Workman 07390 Operator's Manual

•
Do not remove the fuel cap or add fuel with the
engine running.
•
Allow the engine to cool before refueling.
•
Do not refuel the machine indoors.
•
Do not store the machine or fuel container where
there is an open flame, spark, or pilot light, such
as on a water heater or on other appliances.
•
If you spill fuel on your clothing, change your
clothing immediately.
•
Do not overfill the fuel tank. Replace the fuel cap
and tighten it securely.

General Operation

•
The operator and passenger should remain seated
whenever the machine is in motion. The operator
should keep both hands on the steering wheel,
whenever possible, and the passenger should use
the handholds provided. Keep your arms and legs
within the machine body at all times.
•
Drive slower and turn less sharply when you
are carrying a passenger. Remember that your
passenger may not be expecting you to brake
or turn, and may not be ready. Do not carry
passengers in the cargo bed or on attachments.
•
Do not overload the machine. The name plate
(located under the seat assembly) shows the
load limits for the machine. Do not overfill the
attachments or exceed the machine maximum
gross vehicle weight (GVW).
•
When starting the engine, do the following:
1. Park the machine on a level surface.
2. Engage the parking brake.
3. Disengage the PTO (if equipped) and return
the hand-throttle lever to the O
equipped).
4. Ensure that the hydraulic-lift lever is in the
center position.
5. Press in the brake pedal.
6. Keep your foot off the accelerator pedal.
7. Turn the key switch to the S
•
Failure to operate the machine safely may result in
an accident, tip-over of the machine, and serious
injury or death. Drive carefully. To prevent tipping
or loss of control, take the following precautions:
– Use extreme caution, reduce the speed of
the machine, and maintain a safe distance
around sand traps, ditches, creeks, ramps, any
unfamiliar areas, or other hazards.
– Watch for holes or other hidden hazards.
– Use caution when operating the machine on
a steep slope. Normally, travel straight up
position (if
FF
•
position.
TART
•
•
5
and down slopes. Reduce the speed of the
machine when making sharp turns or when
turning on hillsides. Avoid turning on hillsides
whenever possible.
– Use extra caution when operating the machine
on wet surfaces, at higher speeds, or with a full
load. Stopping time increases with a full load.
– Avoid sudden stops and starts. Do not go
from reverse to forward or forward to reverse
without first coming to a complete stop.
– Do not attempt sharp turns or abrupt
maneuvers or other unsafe driving actions that
may cause a loss of control of the machine.
– When dumping, do not let anyone stand behind
the machine and do not dump the load on
anyone's feet.
– Keep all bystanders a safe disaway from the
machine. Before backing up, look to the rear
and ensure that no one is behind the machine.
Back up slowly.
– Watch out for traffic when near or crossing
roads. Always yield the right of way to
pedestrians and other machines. Always
signal your turns or stop early enough so that
other persons know what you plan to do. Obey
all traffic rules and regulations.
– Do not operate the machine in or near an
area in which there is dust or fumes in the air
that are explosive. The electrical and exhaust
systems of the machine can produce sparks
capable of igniting explosive materials.
– Always watch out for and avoid low overhangs
such as tree limbs, door jambs, overhead
walkways, etc. Ensure that there is enough
room overhead to easily clear the machine and
your head.
– If you are ever unsure about the safe operation
of the machine, stop your work, and ask your
supervisor.
Before getting off the seat, do the following:
1. Park the machine on a level surface.
2. Engage the parking brake.
3. Lower the cargo bed.
4. Shut off the engine and remove the key.
Note:
If the machine is on an incline, block the
wheels after getting off the machine.
Do not touch the engine, transmission, muffler, or
muffler manifold while the engine is running, or
soon after you stop the machine, because these
areas may be hot enough to cause burns.
If the machine ever vibrates abnormally, stop the
machine immediately, shut off the engine, wait for
all movement to stop, and inspect for damage.