Table of Contents
Advertisement
Paper type can be changed
in the configuration menu.
Paper types and grades
available:
Type 0 - Monochrome grades
Type 4 - Two-color grades
Type 5 - Two-color grades
See page 48
and
Programming
guide
for more information.
When the printer is configured
for USB, this location will show
either: "USB Driver Type: Printer
Class" or "USB Driver Type:
Comm Class. "
Sample diagnostic menu and print test for serial connection(show approximately 60% of size). Ethernet diagnostic printout
not shown. Ethernet parameters can not be changed in the configuration menu.
189-9200303 Rev. E
*** A760 - Diagnostics Form ***
*** A760 – Diagnostics Form ***
Model number
: A760-1215
Model number
:
Serial number
: 0000000000
Serial number
:
Boot Firmware
Boot Firmware
Revision
: V3.02
Revision
:
CRC
: 9288
CRC
:
P/N
:
P/N
: 189-7600281A
Flash Firmware
Flash Firmware
Revision
:
Revision
: V3.01
CRC
:
CRC
: 3846
P/N
:
P/N
: 189-7600279A
H/W parameters
H/W parameters
Flash Memoriy Size
:
Flash Memory Size
: 2 Mbytes
Flash Logos/Fonts
:
Flash Logos/Fonts
: 960 kbytes
Flash User Storage
:
Flash User Storage
: 64 kbytes
SRAM Size
:
Head setting
Flash Journal Size
:
: 64 kbytes
Paper Type setting
:
SRAM Size
: 512 kbytes
Color Density Adj
:
Head settting
: D
Print Density (Mono)
:
Motor ID
: 0
Max Speed
:
Paper Type Setting
: Type 0, Monochrome
Max Power
:
Color Density Adj
: n/a
Alternate Reset
:
Print Density, Mono
: 100%
Knife
:
Max Speed
: 180 mm/sec
Paper Low Sensor
:
Max Power
: 55 W
MICR
:
Knife
: Enabled
MICR Dual Pass
:
Paper Low Sensor
: Enabled
MICR DC offset
:
Check Flip
Paper Low Extension
:
: Disabled
MICR
: Enabled
Comm. Interface
MICR Dual Pass
: Disabled
RX Buffer Size
:
MICR DC o set
: 7F
Interface type
:
MICR Discriminate
: Auto
Parameters
Check Flip
: Disabled
Baud Rate
:
Slip Alignment
: 13h/19d
Data Bits
:
Stop Bit
:
Comm. Interface
Parity
:
RX Bu er Size
: 4096
Flow Control
:
Interface Type
: RS232/USB
Reception Errors
:
Alternative DTR/DSR :
Parameters
Baud Rate
: 115200
USB Driver Type
:
Data Bits
: 8
Stop Bit
: 1
Resident Code Pages
:
Parity
: NONE
Flow Control
: DTR/DSR
Available Paper Types
:
Reception Errors
: Ignore
USB Driver Type
: Printer Class
USB Packet w/Error
: Reject
Logo(s) defined
:
User Char(s) defined
:
To enter Printer Config Menu :
1) Flip DIP switch #1 up
2) Reset the printer, while holding
the Paper Feed button down
12/2012
Chapter 3: Setting up the Printer
*** A760 – Printer Config Menu ***
This config menu allows you to set general printer
parameters
A760-1125
A012451679
Sub-menus are entered and selections are made using
the Paper Feed Button
V1.03
– short click : Feed Button is quickly depressed
FFDE
189-7600118A
– long click : Feed button is held down for more
V1.03
7196
CAUTION!!
189-7600117A
The settings are predetermined in factory and
should generally not be changed.
If you must change the settings do so carefully
1 Mbyte
to avoid changing other functions.
320 kbytes
0 kbytes
****************
256 kbytes
D
**************************************
Type 1, Version 0
100%
**************************************
100%
Select a sub-menu :
100 mm/sec
– EXIT
55 W
– Print Current Configuration
Disabled
– Set Communication Interface
Enabled
– Set Diagnostics Modes
Enabled
– Set Emulation/Software Options - >
Enabled
– Set Hardware Options
Disabled
– Set Paper Type
80
Enabled
Enter code, then hold Button DOWN
at least 1 second to validate
4096
RS232/USB
115200
Important: Ensure that the
8
1
configuration settings match
NONE
DTR/DSR
your host computer; if not, enter
Ignore
Disabled
the configuration menu to make
Printer Class
changes.
437, 850, 852. 858
860, 863, 865, 866
1252, 862, 737
00.00 01.00 05.00
Current printer tallies are
YES
printed after the diagnostic
NO
information and will vary per
printer use.
A760 Two-Color Thermal/Impact Hybrid Printer: User Guide
then released
than 1 second then released
MAIN MENU
- >
1 click
- >
2 clicks
- >
3 clicks
- >
4 clicks
5 clicks
- >
6 clicks
- >
7 clicks
23
Advertisement
Table of Contents
